reset FORD ESCORT 1996 7.G Owners Manual

27 [SR08200(ALL)06/94]
If your shoulder belts stop working after a
collision, the fuel pump shut-off switch may
have been triggered. Minor parking lot bumping
and severe road impacts (such as potholes) may
trigger the switch even when there is no
apparent body damage. In many instances, you
might not even know that the switch has been
triggered. The shut-off switch cuts power to the
motors that move the shoulder belts in addition
to stopping the flow of fuel to the engine. To
reset the switch, seeEngine, starting after a
collisionin the Index.
[SR08300(ALL)04/93]
If your shoulder belts are not working properly,
get your vehicle serviced as soon as possible.
[SR08400(ALL)04/93]
If the fuel pump shut-off switch is not the cause
for the shoulder belt not moving, have the
system serviced by a qualified technician as soon
as possible.
[SR08450(ALL)04/91]
RWARNING
If the shoulder belt is released from the
emergency release buckle, store the tongue
end away from the seat tracks. Failure to
do this may result in the seat belt being
cut or torn when the seat is adjusted
forward or back. Any damaged shoulder
belt must be replaced.
[SR08500(E )07/93]
Manual Front Lap and Shoulder Belt
(Available only on Canadian vehicles)
[SR08580(E )08/95]
While in motion, the combination lap and
shoulder belt adjusts to your movement.
However, if you brake hard, turn hard, or if
your vehicle receives an impact of 5 mph
(8 km/h) or more, the lap and shoulder belt
locks and helps reduce your forward movement.
The retractor can be made to lock by jerking on
the belt.
File:03ctsre.ex
Update:Tue Sep 19 15:05:35 1995

111
*
[ST09800(ALL)05/95]
NOTE: If your vehicle is equipped with an
automatic transaxle, your vehicle has
an interlock that prevents you from
shifting out of P (Park) unless your
foot is on the brake pedal.
%*
[ST09860(ALL)04/95]
If the engine does not start after two attempts:
*
[ST09880(ALL)03/95]
1. Turn the key to the OFF position and wait
about two minutes.
*
[ST09890(ALL)04/95]
2. Press the accelerator all the way to the floor
and hold it.
*
[ST09900(ALL)04/95]
3. Turn the ignition key to the START position.
*
[ST09910(ALL)04/95]
4. Release the ignition key when the engine
starts.
*
[ST09920(ALL)04/95]
5. Release the accelerator gradually as the
engine speeds up. Then drive away in the
normal manner.
*
[ST09930(ALL)04/95]
If the engine still does not start, the fuel pump
shut-off switch may have been triggered. For
directions on how to reset the switch seeFuel
Pump Shut-Off Switchlater in this chapter.
[ST10200(ALL)06/93]
A computer system controls the engine's idle
RPM. When you start your vehicle, the engine's
idling RPM normally runs higher than when
warm. The engine idle control system should
only be serviced by a qualified technician.
*
[ST10290(ALL)07/95]
If the engine idle speed does not slow down
automatically, do not allow your vehicle to idle
for more than 10 minutes. Have the vehicle
checked.
File:04ctste.ex
Update:Tue Sep 19 14:42:54 1995

113
*
[ST11105(ALL)03/95]
For best results, plug the heater in at least three
hours before you start your vehicle. Using the
heater for longer than three hours will not
damage the engine, so you can plug it in at
night to start your vehicle the following
morning.
%
*
[ST11110(ALL)03/95]
If the Engine Cranks but Does
Not Start or Does Not Start After
a Collision
*
[ST11120(ALL)07/95]
The Fuel Pump Shut-off Switch
*
[ST11130(ALL)07/95]
If the engine cranks but does not start or does
not start after a collision, the fuel pump shut-off
switch may have been triggered. The shut-off
switch is a device intended to stop the fuel
pump when your vehicle has been involved in a
substantial jolt.
[ST11140(ALL)03/95]
Once the shut-off switch is triggered, you must
reset the switch by hand before you can start
your vehicle. The fuel pump shut-off switch is
located behind the right rear trim panel in the
trunk. You can reach the switch to reset it
through the access hole.
File:04ctste.ex
Update:Tue Sep 19 14:42:54 1995

114 [ST11150(E )08/95]
half page art:0070153-BLocation of the fuel pump shut-off switch (location on
wagon similar)
*
[ST11170(ALL)05/95]
RWARNING
If you see or smell fuel, do not reset the
switch or try to start your vehicle. Have
all the passengers get out of the vehicle
and call the local fire department or a
towing service.
*
[ST11180(ALL)03/95]
If your engine cranks but does not start after a
collision or substantial jolt:
[ST11190(ALL)03/95]
1. Turn the key in the ignition to LOCK.
*
[ST11200(ALL)03/95]
2. Check under the vehicle for leaking fuel.
*
[ST11210(ALL)03/95]
3. If you do not see or smell fuel, push the red
reset button down. If the button is already
set, you may have a different mechanical
problem.
File:04ctste.ex
Update:Tue Sep 19 14:42:54 1995

129 [LG20175(ALL)02/94]
4. If the oil level is low, add as much oil as
necessary before you drive your vehicle
again. Do not overfill. Do not operate the
engine when the oil pressure light is on,
even if the oil level is correct. For more
information about adding oil, seeAdding
engine oilin the Index.
%*
[LG20176(ALL)01/95]
Fuel Gauge
*
[LG20177(ALL)06/93]
The fuel gauge displays approximately how
much fuel is in the fuel tank only when the
ignition switch is ON.
[LG20178(ALL)06/93]
For proper fuel gauge indication after adding
fuel, the ignition switch should be in the OFF
position while the vehicle is being refueled.
*
[LG20179(ALL)06/93]
The fuel gauge indicator may vary slightly when
the vehicle is in motion.
[LG20180(ALL)06/93]
With the ignition switch OFF, the fuel gauge
indicator may drift from the ignition switch ON
position.
%*
[LG20181(ALL)01/95]
Speedometer
*
[LG20182(ALL)01/95]
The speedometer tells you how many miles
(kilometers) per hour your vehicle is moving.
%*
[LG20183(ALL)01/95]
Odometer
*
[LG20184(ALL)01/95]
The odometer tells you the total number of miles
(kilometers) your vehicle has been driven.
%*
[LG20185(ALL)11/94]
Trip Odometer
*
[LG20186(ALL)11/94]
The trip odometer tells you how many miles
(kilometers) your vehicle has been driven since
the last reset. Press the reset button to return the
trip odometer to zero.
File:05ctlge.ex
Update:Tue Sep 19 14:44:43 1995

166 [SC08500(ALL)08/95]NOTE: If your vehicle is equipped with an
automatic transaxle, and if your speed
increases above your set speed while
driving ink(Overdrive) on a
downhill grade, you may want to shift
to D (Drive). This will reduce vehicle
speed. Speed control cannot reduce the
vehicle speed if it goes above your set
speed on a downhill grade.
[SC08550(ALL)08/95]
NOTE: If your vehicle is equipped with a
5-speed manual transaxle, and if your
speed increases above your set speed
while driving in 5 (fifth) gear on a
downhill grade, you may want to shift
to 4 (Fourth) gear to reduce vehicle
speed. Depressing the clutch pedal
cancels speed control, therefore speed
control must be reset by pressing the
SET ACCEL or RESUME switches.
Speed control cannot reduce the vehicle
speed if it goes above your set speed
on a downhill grade.
[SC09600(ALL)08/95]
RWARNING
To keep control of your vehicle, do not
use the speed control in heavy traffic or
on roads that are winding, slippery, or
unpaved.
[SC09650(ALL)08/95]
If you want to speed up momentarily or regain
preset speed on hills when the speed control is
operating, accelerate using the accelerator pedal.
Manually accelerating to a higher speed does not
interfere with the speed control; when you take
your foot off the accelerator, the vehicle returns
to the set speed.
File:07ctsce.ex
Update:Tue Sep 19 14:47:40 1995

167 [SC09700(ALL)09/95]
NOTE: Do not shift to N (Neutral) when using
the speed control. This will cause the
engine to overspeed.
[SC09750(ALL)09/95]
When driving uphill, especially with a heavy
load, significant speed drops may occur. If the
speed drops more than 8 to 14 mph
(13-23 km/h) the automatic speed control will
cancel. You may need to control your speed
manually while driving up steep grades in order
to maintain the selected speed.
[SC09800(ALL)08/95]
To turn off the speed control or to reset
speed:
[SC09850(ALL)08/95]
half page art:0070278-A[SC09900(ALL)08/95]
The speed control is turned off each time you
turn off the vehicle.
File:07ctsce.ex
Update:Tue Sep 19 14:47:40 1995

200
*
[AS02600(ALL)08/95]
q
Using the ªSCAN/TUNEº button to scan
radio stations
*
[AS02700(ALL)08/95]
Pressing the ªSCAN/TUNEº button once
enters the scan mode (display will indicate
ªSCNº). Pushing the top
ahalf of the
ªSEEKº button will begin the scan mode up
the frequency band, stopping on each
listenable station for approximately five
seconds. Pushing the bottom
bhalf of the
ªSEEKº button will begin the scan mode
down the frequency band, again stopping on
each listenable station for approximately five
seconds.
*
[AS02800(ALL)08/95]
To stop the scan mode on the presently
sampled station press the ªSCAN/TUNEº
button again.
*
[AS03000(ALL)08/95]
q
Setting the Station Memory Preset buttons
%*
[AS03100(ALL)08/95]
Your radio is equipped with 5 station
memory buttons. These buttons can be used
to select up to 5 preset AM stations and 10
FM stations (5 in FM1 and 5 in FM2). Follow
the easy steps below to set these buttons to
the desired frequencies.
*
[AS03200(ALL)08/95]
1. Select a band, then select a frequency.
*
[AS03400(ALL)08/95]
2. Press one of the memory preset buttons and
hold the button until the sound returns. That
station is now held in memory on that
button.
*
[AS03500(ALL)08/95]
3. Follow the two steps above for each station
memory preset button you want to set.
File:09ctase.ex
Update:Tue Sep 19 14:51:59 1995

201
*
[AS03515(ALL)08/95]
q
Using the Automatic Memory Load feature
*
[AS03520(ALL)03/95]
If no stations are in memory preset, you can
activate theAuto Memory Loadfeature by
pressing and holding the ªAUTO PRESETº
buttonfor approximately three seconds.
Auto Memory Load sets all memory buttons
in AM, FM1 and FM2 sequentially by seeking
out the first six strong stations for the
respective band and storing them in memory
buttons 1-5. (FM2 will store the second set of
strong stations from the FM band.)
*
[AS03525(ALL)08/95]
With Auto Memory Store, you can
continually set strong stations into your
memory buttons without losing your existing
memory presets, which is especially handy
while traveling. Your radio will automatically
set your memory buttons to the strong local
stations so you don't have to continually
manually tune to existing stations.
*
[AS03530(ALL)08/95]
Activate Auto Memory Store by pushing the
ªAUTO PRESETº button once. Your radio
will set the first five strong stations of the
band you are in (AM, FM1 or FM2) into the
memory buttons. The display will show
ªAUTO,º then run through the frequencies,
stopping momentarily on the stations being
set into the memory buttons. The radio is
now in the ªAUTOº mode and the display
will show ªAUTOº each time a preset is
activated.
*
[AS03535(ALL)08/95]
NOTE: If there are fewer than five strong
stations in the frequency band, the
remaining unfilled buttons will store
the last strong station detected on the
band.
File:09ctase.ex
Update:Tue Sep 19 14:51:59 1995

202
*
[AS03540(ALL)08/95]
After all stations have been filled, the radio
will begin playing the station stored on
memory button 1.
*
[AS03545(ALL)08/95]
To deactivate the Auto Memory Store mode
and return to the manually-set memory
button stations (or those stations set using
Auto Memory Load), simply push the
ªAUTO PRESETº button. Display will show
ªAUTOº then ªOFF.º The next time Auto
Memory Store is activated on that band, the
radio will store the next set of five strong
stations.
*
[AS04400(ALL)08/95]
Using the ªAUDIOº button to adjust the
tone balance and speaker output
*
[AS04500(ALL)08/95]
q
Increasing or decreasing bass response
*
[AS04600(ALL)08/95]
Push the ªAUDIOº button repeatedly until
the display reads ªBASS.º Push the ª+º side
of the ªVOLº button to increase bass (more
ªlowsº), and push the ª-º side to decrease
bass (less ªlowsº).
*
[AS04700(ALL)08/95]
q
Increasing or decreasing treble response
*
[AS04800(ALL)08/95]
Push the ªAUDIOº button repeatedly until
the display reads ªTREB.º Push the ª+º side
of the ªVOLº button to increase treble (more
ªhighsº), and push the ª-º side to decrease
treble (less ªhighsº).
*
[AS05050(ALL)08/95]
q
Adjusting speaker balance
*
[AS05100(ALL)08/95]
Balance control allows you to adjust the
sound distribution between the right and left
speakers. Push the ªAUDIOº button
repeatedly until the display reads ªBAL.º
Push the ª+º side of the ªVOLº button to
shift the sound to the right speakers, and
push the ª-º side to shift the sound to the
left speakers.
File:09ctase.ex
Update:Tue Sep 19 14:51:59 1995