light FORD ESCORT 1996 7.G Owner's Guide

208
*
[AS07400(ALL)08/95]
How to eject the disc
*
[AS07500(ALL)08/95]
Push the ªEJECTº button to stop play, eject the
disc and resume radio operation of your audio
system.
*
[AS07600(ALL)08/95]
NOTE: You can eject the disc while the radio
power and/or ignition is on or off.
%*
[AS08100(ALL)08/95]
How To Take Care of and Clean Your CD
Player and Discs
*
[AS08200(ALL)08/95]
To ensure the continued performance of your
Ford Compact Disc Player, carefully read the
following precautions:
*
[AS08300(ALL)08/95]
q
Always handle the disc by its edge. Never
touch the playing surface.
*
[AS08400(ALL)08/95]
q
Before playing, inspect the disc for any
contamination. If needed, clean the disc with
an approved disc cleaner, such as the
DiscwasherHCompact Disc Cleaner or the
Allsop 3HCompact Disc Cleaner, by wiping
from the center out to the edges.Do not use
a circular motion to clean.
*
[AS08500(ALL)08/95]
q
Do not clean discs with solvents such as
benzine, thinner, commercially available
cleaners or antistatic spray intended for
analog records.
*
[AS08600(ALL)08/95]
q
Do not expose the disc to direct sunlight or
heat sources such as defroster and floor
heating ducts. Do not leave any discs in a
parked car in direct sunlight where there may
be a considerable rise in temperature or
damage may result.
File:09ctase.ex
Update:Tue Sep 19 14:51:59 1995

219
*
[AS27600(ALL)08/95]
Tips on Caring for the Cassette Player and
Tapes
*
[AS27700(ALL)08/95]
In order to keep your cassette tape player
performing the way it was meant to, read and
follow these simple precautions:
*
[AS27800(ALL)08/95]
q
Only cassettes that are 90 minutes long or
less should be used. Tapes longer than 90
minutes are thinner and subject to breakage
or may jam the tape player mechanism.
*
[AS27900(ALL)08/95]
q
Protect cassettes from exposure to direct
sunlight, high humidity and extreme heat or
cold. If they are exposed to extreme
conditions, allow them to reach a moderate
temperature before playing.
*
[AS28000(ALL)08/95]
q
Loose labels on cassette tapes can become
lodged in the mechanism. Remove any loose
label material before inserting a cassette.
*
[AS28100(ALL)08/95]
q
If a tape is loose inside the cassette, tighten it
before playing by putting your finger or a
pencil into one of the holes and turning the
hub until the tape is tight.
*
[AS28200(ALL)08/95]
q
Do not leave a tape in the cassette tape
player when not in use. High heat in the
vehicle can cause the cassette to warp.
*
[AS28300(ALL)08/95]
q
Using a Ford Cassette Cleaning Cartridge to
clean the tape player head after 10-12 hours
of play will help maintain the best playback
sound and proper tape operation.
File:09ctase.ex
Update:Tue Sep 19 14:51:59 1995

221
*
[AS36200(ALL)08/95]
Several sources of static are normal conditions
on AM frequencies. These can be caused by
power lines, electric fences, traffic lights and
thunderstorms.
*
[AS36300(ALL)08/95]
Another reception phenomenon isStrong Signal
Capture and Overload. This can occur when
listening to a weak station and when passing
another broadcast tower. The close station may
capture the more distant station, although the
displayed frequency does not change. While
passing the tower, the station may switch back
and forth a few times before returning to the
original station.
*
[AS36400(ALL)08/95]
When several broadcast towers are present
(common in metropolitan areas) several stations
may overload the receiver, resulting in
considerable station changing, mixing and
distortion.
*
[AS36500(ALL)08/95]
Automatic gain control circuitry for both AM
and FM bands has been incorporated into this
system to reduce strong signal capture and
overload.
%
*
[AS36600(ALL)08/95]
All About Radio Frequencies
*
[AS36800(ALL)08/95]
Not all frequencies will be assigned to a given
area. This radio will tune to each of these
frequencies using manual tune and no fine
tuning is necessary as radio stations may not use
other frequencies.
*
[AS36900(ALL)08/95]
Some FM radio stations advertise a
ªrounded-offº frequency which is not the
frequency they actually broadcast on. For
example, a radio station that is assigned a
frequency of 98.7 MHz may call itself ªRadio 99º
even though 99.0 MHz is not an allowable FM
broadcast frequency.
File:09ctase.ex
Update:Tue Sep 19 14:51:59 1995

227
*
[DR05800(ALL)06/95]
When to use D (Drive)
*
[DR06000(ALL)04/95]
D (Drive) eliminates the excessive shifting
between third and fourth gears that your vehicle
sometimes does when you are traveling through
hilly terrain injOverdrive. It also gives more
engine braking to slow your vehicle on
downgrades thanjOverdrive.
[DR06100(ALL)09/95]
When to use L (Low)
[DR06200(ALL)08/93]
Use L (Low) when more power is needed to
drive up steep hills. It also gives more engine
braking than Drive when driving on hilly roads.
[DR06300(ALL)06/95]
Do not go faster than 38 mph (60 km/h) in this
gear. You can upshift from L (Low) to Drive or
from L (Low) to Overdrive at any speed.
[DR06320(ALL)09/95]
Reverse
*
[DR06340(ALL)08/95]
With the gearshift in the R (Reverse) position,
the vehicle will move backward. You should
always come to a complete stop before shifting
into or out of R (Reverse).
[DR06350(ALL)08/95]
Neutral
[DR06379(ALL)09/95]
In N (Neutral), the wheels of the transaxle are
not locked. Your vehicle will roll freely, even on
the slightest incline, unless the parking brake or
brakes are on.
File:10ctdre.ex
Update:Tue Sep 19 14:53:34 1995

231 [DR08700(ALL)06/93]
For cruising, you should upshift at the following
speeds:
[DR08800(ALL)06/93]
ten pica chart:0070155-A[DR09400(ALL)08/95]
Upshift indicator light (If equipped)
[DR09500(ALL)09/93]
After the engine warms up, the upshift light will
come on if you could get better fuel economy by
shifting to the next higher gear. The vehicle will
not be harmed if the transaxle is not shifted
when the light comes on, but the vehicle will
use more fuel.
[DR09600(ALL)09/93]
The shift indicator light can be ignored when
you are downshifting, on steep hills, using the
engine to ºbrakeª the vehicle, or need more
power for a difficult acceleration.
%*
[DR09700(ALL)05/95]
Downshifting
*
[DR09800(ALL)03/95]
When you slow down or climb a steep hill,
always downshift before the engine starts to lose
power. Downshifting reduces the chance of
stalling and gives your vehicle better acceleration
to increase speed again.
*
[DR09900(ALL)03/95]
When you drive down steep hills, downshifting
helps you keep a safe speed and helps prevent
unnecessary wear on the brakes.
File:10ctdre.ex
Update:Tue Sep 19 14:53:34 1995

233
*
[DR16800(ALL)05/95]
If your vehicle does not have anti-lock brakes,
extreme braking can make the wheels lock and
slide, causing you to lose control of the steering.
If the wheels lock, release the brake pedal and
repeat the ºsqueezeª technique.
*
[DR16900(ALL)05/95]
Do not drive with your foot resting on the brake
pedal; you will wear out the linings and increase
your vehicle's stopping distance. Brake rotor
damage may also eventually occur.
*
[DR17000(ALL)05/95]
RWARNING
If you are driving down a long or steep
hill, shift to a lower gear. Do not apply
your brakes continuously, as they may
overheat and become less effective.
*
[DR17100(ALL)02/95]
Occasional brake squeal during light to moderate
stops does not affect the function of the brake
system and is normal. However, if the squeal
becomes annoyingly loud or increases
significantly in frequency of occurrence, return
the vehicle to your dealer for inspection.
[DR17200(ALL)09/89]
The high-mount brakelamp will light when you
apply the brakes.
[DR17300(ALL)05/95]Anti-lock Brake System
(If equipped)
*
[DR17325(ALL)11/94]
Your vehicle may come with the optional
anti-lock brake system. Whenever your wheels
start to lock (which could result in a skid) the
anti-lock brake system prevents the lock-up by
automatically releasing and re-applying the
brakes. The brake pedal will pulsate as a result
of the automatic releasing and re-applying of the
brakes. In spite of this improvement in braking
performance, you should continue to be cautious
in all hazardous driving situations, especially
when driving on hazardous road surfaces. Even
File:10ctdre.ex
Update:Tue Sep 19 14:53:34 1995

234with your anti-lock brake system, you may not
have total control of your vehicle when braking
on roads with loose surfaces such as snow or
gravel, holes in the pavement, or alternating
patches of slippery and dry surfaces.
[DR17350(ALL)04/94]
Each time you turn the ignition key to the ON
position, the anti-lock brake system will function
through one test cycle. When this happens, the
anti-lock light (ABS) will come on for up to six
seconds. If the light stays on longer than six
seconds, shut off the engine and restart. If it
remains on, it means the anti-lock brake system
is disabled and should be serviced immediately
to restore the benefits of the anti-lock feature.
Normal braking is not affected unless the red
brake warning light is also lit.
[DR17400(ALL)02/94]
The anti-lock brake system has self-check
capabilities. As described above, the system
turns on the anti-lock light each time you start
your engine. After the engine is started and the
anti-lock light turns off, the system performs
another test the first time the vehicle reaches
7 mph (11 km/h). The system turns on the ABS
pump motor for approximately 1/2 second. At
this time, a mechanical noise may be heard. This
is a normal part of the self-check feature. If a
malfunction is found during this check the
anti-lock light will come on.
*
[DR17500(ALL)08/95]
Ford Motor Company has not found any
negative effects of mobile radio transmitting
equipment installed on vehicles with the ABS
system providing that the radio is installed
according to the radio manufacturer's
instructions. However, if you have had a mobile
radio transmitter installed and the ABS light
comes on (at any time other than immediately
File:10ctdre.ex
Update:Tue Sep 19 14:53:34 1995

236
*
[DR18400(ALL)06/95]
RWARNING
Always set the parking brake fully and
make sure that the gearshift is securely
latched in P (Park) (automatic transaxle) or
in 1 (First) (manual transaxle).
*
[DR18475(ALL)06/95]
RWARNING
Never leave your vehicle unattended
while it is running.
*
[DR18600(ALL)03/95]
Always check the Brake Warning Light each
time you start your engine. Driving with the
parking brake on will cause the brakes to wear
out quickly and will reduce the fuel economy.
*
[DR18700(ALL)01/93]
RWARNING
If the parking brake is fully released, but
the Brake System light remains on, have
the brakes checked immediately. They
may not be working properly.
*
[DR18800(ALL)11/91]
RWARNING
To prevent personal injury, do not release
the parking brake while outside the
vehicle.
*
[DR19000(ALL)06/95]
The parking brake is not designed to stop a
moving vehicle, but you can use the parking
brake to stop your vehicle in an emergency if
the normal brakes fail. However, since the
parking brake applies only the rear brakes, the
stopping distance will increase greatly and the
handling of your vehicle will be adversely
affected.
File:10ctdre.ex
Update:Tue Sep 19 14:53:34 1995

239
*
[DR20750(ALL)03/95]
RWARNING
If your vehicle has speed control, do not
use it on slippery roads. You could lose
control of your vehicle and could injure
someone.
*
[DR20800(ALL)01/95]
If you have an automatic transaxle and your
vehicle gets stuck (for example, in mud or
snow), you may try to ºrockª it out of the spot.
Shift, in a steady rhythm, between forward and
reverse gears. While in each gear, press lightly
on the accelerator and release.
*
[DR20900(ALL)05/95]
RWARNING
Do not spin the wheels at over 35 mph
(55 km/h). The tires may fail and injure a
passenger or bystander.
*
[DR21000(ALL)03/95]
By moving the vehicle backward and forward,
you may gain enough momentum to move out
of the spot. Do not rock the vehicle for more
than a few minutes. This may overheat the
engine, damage the transaxle, or damage the
tires. If you are still stuck after a minute or two
of rocking, call for a tow truck.
%*
[DR21200(ALL)01/95]
High water
*
[DR21300(ALL)01/95]
Do not drive through flooded areas unless you
are sure that the water is below the bottom of
the wheel rims.
*
[DR21400(ALL)04/94]
If you must drive through high water, drive
slowly. You may have limited traction or wet
brakes, so allow extra stopping distance because
your vehicle will not stop as quickly as usual.
*
[DR21500(ALL)01/95]
After you drive through the standing water,
apply your brakes gently several times as your
vehicle moves slowly. This helps to dry the
brakes.
File:10ctdre.ex
Update:Tue Sep 19 14:53:34 1995

243
Roadside Emergencies
%*
[RE00380(ALL)03/95]
Jump-Starting Your Vehicle
[RE00390(ALL)01/92]
Your vehicle's battery may die if you leave the
lights or any electrical equipment on after you
turn the engine off. If this happens, you may be
able to jump-start from a booster battery to start
your vehicle.
*
[RE00400(ALL)02/95]
RWARNING
The gases around the battery can explode
if exposed to flames, sparks, or lit
cigarettes. An explosion could result in
injury or vehicle damage.
*
[RE00500(ALL)02/95]
RWARNING
To protect yourself when charging a
battery, always shield your face and eyes.
Make sure that you can breathe fresh air.
%*
[RE00600(ALL)06/95]
RWARNING
Applying too much pressure on the ends
when lifting a battery could cause acid to
spill. Lift the battery with a carrier or
with your hands on the opposite corners.
%*
[RE00700(ALL)07/95]
RWARNING
Batteries contain sulfuric acid which burns
skin, eyes, and clothing.
File:12ctree.ex
Update:Tue Sep 19 14:55:16 1995