service reset FORD ESCORT 1996 7.G Owners Manual

27 [SR08200(ALL)06/94]
If your shoulder belts stop working after a
collision, the fuel pump shut-off switch may
have been triggered. Minor parking lot bumping
and severe road impacts (such as potholes) may
trigger the switch even when there is no
apparent body damage. In many instances, you
might not even know that the switch has been
triggered. The shut-off switch cuts power to the
motors that move the shoulder belts in addition
to stopping the flow of fuel to the engine. To
reset the switch, seeEngine, starting after a
collisionin the Index.
[SR08300(ALL)04/93]
If your shoulder belts are not working properly,
get your vehicle serviced as soon as possible.
[SR08400(ALL)04/93]
If the fuel pump shut-off switch is not the cause
for the shoulder belt not moving, have the
system serviced by a qualified technician as soon
as possible.
[SR08450(ALL)04/91]
RWARNING
If the shoulder belt is released from the
emergency release buckle, store the tongue
end away from the seat tracks. Failure to
do this may result in the seat belt being
cut or torn when the seat is adjusted
forward or back. Any damaged shoulder
belt must be replaced.
[SR08500(E )07/93]
Manual Front Lap and Shoulder Belt
(Available only on Canadian vehicles)
[SR08580(E )08/95]
While in motion, the combination lap and
shoulder belt adjusts to your movement.
However, if you brake hard, turn hard, or if
your vehicle receives an impact of 5 mph
(8 km/h) or more, the lap and shoulder belt
locks and helps reduce your forward movement.
The retractor can be made to lock by jerking on
the belt.
File:03ctsre.ex
Update:Tue Sep 19 15:05:35 1995

111
*
[ST09800(ALL)05/95]
NOTE: If your vehicle is equipped with an
automatic transaxle, your vehicle has
an interlock that prevents you from
shifting out of P (Park) unless your
foot is on the brake pedal.
%*
[ST09860(ALL)04/95]
If the engine does not start after two attempts:
*
[ST09880(ALL)03/95]
1. Turn the key to the OFF position and wait
about two minutes.
*
[ST09890(ALL)04/95]
2. Press the accelerator all the way to the floor
and hold it.
*
[ST09900(ALL)04/95]
3. Turn the ignition key to the START position.
*
[ST09910(ALL)04/95]
4. Release the ignition key when the engine
starts.
*
[ST09920(ALL)04/95]
5. Release the accelerator gradually as the
engine speeds up. Then drive away in the
normal manner.
*
[ST09930(ALL)04/95]
If the engine still does not start, the fuel pump
shut-off switch may have been triggered. For
directions on how to reset the switch seeFuel
Pump Shut-Off Switchlater in this chapter.
[ST10200(ALL)06/93]
A computer system controls the engine's idle
RPM. When you start your vehicle, the engine's
idling RPM normally runs higher than when
warm. The engine idle control system should
only be serviced by a qualified technician.
*
[ST10290(ALL)07/95]
If the engine idle speed does not slow down
automatically, do not allow your vehicle to idle
for more than 10 minutes. Have the vehicle
checked.
File:04ctste.ex
Update:Tue Sep 19 14:42:54 1995

114 [ST11150(E )08/95]
half page art:0070153-BLocation of the fuel pump shut-off switch (location on
wagon similar)
*
[ST11170(ALL)05/95]
RWARNING
If you see or smell fuel, do not reset the
switch or try to start your vehicle. Have
all the passengers get out of the vehicle
and call the local fire department or a
towing service.
*
[ST11180(ALL)03/95]
If your engine cranks but does not start after a
collision or substantial jolt:
[ST11190(ALL)03/95]
1. Turn the key in the ignition to LOCK.
*
[ST11200(ALL)03/95]
2. Check under the vehicle for leaking fuel.
*
[ST11210(ALL)03/95]
3. If you do not see or smell fuel, push the red
reset button down. If the button is already
set, you may have a different mechanical
problem.
File:04ctste.ex
Update:Tue Sep 19 14:42:54 1995

343 %
*
[SV42405(ALL)07/95]
Readiness for Inspection/Maintenance
Testing
*
[SV42410(ALL)07/95]
In some localities it may become a legal
requirement to pass an
Inspection/Maintenance (I/M) test of the
On-Board Diagnostic (OBD) II system. If the
vehicle's powertrain system or its battery has
just been serviced, the OBD II system is reset to
a not ready for I/M testing condition. To
prepare for I/M testing, the law specifies a
ªneed for additional mixed city and highway
driving to complete the checkº of the OBD II
system. As soon as all of the OBD II system
checks are successfully completed, the OBD II
system is set to the ready condition. The amount
of driving required to reach the ready condition
varies with individual driving patterns. To
complete this requirement in the minimum
amount of time, refer to the OBD II Drive Cycle
defined below. If the vehicle owner cannot or
does not want to do the additional driving
required by law, a service center can perform
this drive cycle as it would any other type of
repair work.
[SV42415(ALL)09/95]
OBD II Drive Cycle (1.9L Engine only)
[SV42416(ALL)08/95]
The following steps must be run in the order
shown. If any steps are interrupted, repeat the
preceding step. Any safe driving mode is
acceptable between steps.
[SV42417(ALL)09/95]
NOTE: Always drive vehicle in a safe manner
according to traffic conditions and obey
all traffic laws.
File:15ctsve.ex
Update:Tue Sep 19 14:37:50 1995