ESP FORD EXPEDITION 1997 1.G User Guide

3. Remove the electrical connector
from the bulb by grasping the wire
and pulling it rearward.
4. Remove bulb retainer ring by
turning it counterclockwise about
1/4 turn, then slide the ring off the
plastic base.
5. Without turning, carefully pull
bulb assembly out of parking lamp
assembly.
6. Insert the glass end of the new
bulb into the parking lamp
assembly socket. When the grooves
in the plastic base are aligned,
push the bulb into the socket until
the plastic base contacts the rear
of the socket.
7. Slip bulb retaining ring over the
plastic base and lock the ring into
the socket by turning it clockwise
until you feel a ªstop.º
8. Push the electrical connector
into the rear of the plastic base
until it ªsnaps.º
9. Align top and bottom ribs of
parking lamp assembly with
corresponding slots on front of
vehicle.
10. Push gently until parking lamp
assembly seats (you will hear a snap).
11. Replace screw removed in step 1.
exd_foglamps
Maintenance and care
202

AIMING THE HEADLAMPS
The alignment of your headlamps
should be checked by a qualified
service technician if:
²Oncoming motorists frequently
signal you to deactivate your
high beams, and your high
beams are not activated.
²The headlamps do not seem to
provide enough light for clear
night vision.
²The headlamp beams are
pointed substantially away from
a slightly down and to the right
position.
CLEANING AND CARING FOR
YOUR VEHICLE
Washing your vehicle
Wash your vehicle regularly with
cold or lukewarm water. Never use
strong detergents or soap. If your
vehicle is particularly dirty, use a
quality car wash detergent. Always
use a clean sponge, washing glove
or similar device and plenty of
water for best results. To avoid
spots, avoid washing when the
hood is still warm, immediately
after or during exposure to strong
sunlight.
During winter months, it is
especially important to wash the
vehicle on a regular basis. Large
quantities of dirt and road salt are
difficult to remove, and they also
cause damage to the vehicle.
Remove any exterior accessories,exd_headlamp_aiming
exd_cleaning_info
com_washing_vehicle.01
Maintenance and care
206

SPECIFICATIONS
Lubricant specifications
Item Ford part nameFord part
numberFord
specification
Windshield
washer fluid
reservoirFord Ultra-Clear
Windshield
Washer Fluid
ConcentrateC9AZ-19550-AA
OR -BAESR-M17P5-A
Body hinges,
latches, door
striker plates
and rotors, seat
tracks, fuel filler
door hinge and
spring, hood
latch, auxiliary
latchMulti-Purpose
GreaseD7AZ-19584-AA
OR
D0AZ-19584-AAESR-M1C159-A
AND
ESB-M1C93-B
Lock cylinders,
swing-away
spare tire carrier
padlockPenetrating
LubricantE8AZ-19A501-B ESB-M2C75-B
Parking brake
linkage pivots
and clevisesPremium Life
Long GreaseXG-1-C ESA-M1C75-B
Brake master
cylinderHigh
Performance
DOT 3 Brake
FluidC6AZ-19542-AA ESZ-M6C25-A
Brake pedal
pivot points and
clevisesEngine Oil
SAE-10W- WSS-M2C153-F
exd_lubricant_specifications
Capacities and specifications
215

Item Ford part nameFord part
numberFord
specification
Speedometer,
parking brake
cableSpeedometer
Cable LubricantE6TZ-19581-A ESF-M1C160-A
Engine oil filter Motorcraft
Long Life
Oil Filter(FL-1A)
D9AZ
-6731-AES-E1ZE
-6714-AA
Disc brake
caliper railsDisc Brake
Caliper Slide
GreaseD7AZ-19590-A ESA-M1C172-A
Accelerator
throttle lever
and
transmission
kickdown lever
ball studsPremium Long
Life GreaseXG-1-C ESA-M1C175-B
Ford
conventional
and traction lock
rear axleMotorcraft High
Performance
Synthetic Rear
Axle LubeF1TZ-19580-B WSL-M2C192-A
Ford front axle Thermally
Stable
Motorcraft Front
Axle LubricantXY-75W90-QL WSP-M2C201-A
Transfer case -
Four wheel
driveMotorcraft
MERCONT
Automatic
Transmission
FluidXT-2-QDX MERCONT
Exhaust control
valveRust penetrant
and inhibitorF219A501-A ESR-M99C56-A
Capacities and specifications
217