power steering FORD EXPEDITION 2015 3.G Quick Reference Guide

1 INTERIOR LAMPS
Press and hold the top of
the control to switch on
the interior courtesy lamps.
Press the bottom of the
control to switch off the
interior lamps.
2 LIGHTING CONTROL
Switches off the
headlamps.
Switches on the
parking lamps.
Switches the
headlamps on.
Autolamps: Automatically turns the exterior lamps on
in low light situations.
Pull the control toward you
to switch the fog lamps on.
3 POWER-ADJUSTABLE
FOOT PEDALS* located
to the left of your steering
column lets you move
your brake and accelerator
pedals closer. Press the

arrow to move the pedals
closer to you or the
arrow
to move the pedals further
away from you. Adjust the
pedals only after you stop
the vehicle and place the
transmission in park (P).
4 TILT AND
TELESCOPING
STEERING COLUMN*
lets you adjust the position
of the steering column.
Use the control on the side
of the steering column.
The column automatically
moves to the full up
position when you switch
the ignition off. It returns to
the previous position when
you switch the ignition on.
You can switch this feature
off in the information
display.
For more details about
your information display
functions, please see your
Owner’s Manual.
5 WINDSHIELD WIPERS
AND WASHERS
Rotate the end of the
control away from you to
increase the wiper speed
and toward you to decrease
the wiper speed.
To use the washer feature,
push the end of the lever.
To operate the rear window
wiper, rotate the control.
For a rear wash cycle, rotate
and hold the rear wiper
control
to either the
top or bottom position.
Note: For optimal wiper
performance, clean your
blades and glass regularly.
6 LEFT VEHICLE
INFORMATION
DISPLAY
provides
important vehicle
information through a
constant monitoring of
vehicle systems. The
system notifies you of
potential vehicle problems
by displaying system
warnings followed by a
long indicator tone.
Use the left-hand, 5-way
controls located on your
steering wheel to scroll
through, highlight and make
minor adjustments within a
selected menu.
For more details about
your information display
functions, refer to your
Owner’s Manual.
7 SERVICE ENGINE
SOON LIGHT lights briefly when
you switch the ignition on.
If it remains on or blinks
after you start the engine,
the On-Board Diagnostics
(OBD-II) system detects
a problem. Drive in a
moderate fashion and
contact an authorized
dealer as soon
as possible.
8 CRUISE CONTROL
To set the speed
A. Press and release ON.
B. Accelerate to the
desired speed.
C. Press SET+ and take your
foot off the accelerator.
To set a higher or lower
speed, either press and hold
or press SET+ or SET-
repeatedly until you reach
the desired speed.
To cancel a set speed, tap
the brake pedal. The set
speed will not be erased.
To return to a previously
set speed, press RES .
To switch off, press OFF or
switch the ignition off.
page 5 page 4*if equipped
INSTRUMENT PANEL
7
2
5
6
6
8
13
4

INSTRUMENT PANEL (CONTINUED)
12 A. POWER LIFTGATE CONTROL* lets you open or
close your power liftgate from the driver seat. To use,
press the control.
B. HILL START ASSIST keeps your vehicle stationary
long enough to move your foot from the brake pedal to
the accelerator pedal when your vehicle is on a slope.
Press the control to switch this feature off. It turns back
on automatically after you re-start your vehicle.
C. ADVANCETRAC® WITH RSC® (ROLL STABILITY
CONTROL™) automatically activates when you start
your engine and helps you keep control of your vehicle
when on a slippery surface. The electronic stability
control portion of the system helps avoid skids and
lateral slides, while the roll stability control helps avoid a
vehicle rollover. The traction control system helps avoid
drive wheel spin and loss of traction.
TRAILER SWAY CONTROL * applies your vehicle
brakes at individual wheels and, if necessary, reduces
engine power. If the trailer begins to sway, the stability
control light flashes and the message TRAILER SWAY
REDUCE SPEED appears in the information display.
The first thing to do is slow down your vehicle, then
pull safely to the side of the road and check for proper
tongue load and trailer load distribution. For more
information, please refer to the Towing chapter in your
Owner’s Manual.
9 RIGHT VEHICLE INFORMATION DISPLAY* provides
information about Entertainment, Phone, Climate and
Navigation*. Use the right-hand, 5-way controls located on
your steering wheel to scroll through, highlight and make minor
adjustments within a selected menu. For more information,
refer to the MyFord Touch chapter in your
Owner’s Manual.
10 STEERING WHEEL CONTROLS
Press VOL+ or VOL– to increase or decrease your
volume level.
Press
to access the previous or next radio station,
CD track or preset satellite radio channel.
Press OK repeatedly to access all possible media sources.
Press
to access voice recognition*.
Press
to access SYNC® phone features.
Note: Some of your steering wheel media controls may vary.
See the Steering Wheel chapter in your Owner’s Manual for
more details.
11 PUSH BUTTON START* allows you to start your vehicle by
pressing the ENGINE START STOP button while fully pressing
down on the brake pedal. If you leave your vehicle idling for an
extended period of time, it automatically shuts down. Before
the engine shuts down, a message appears in the information
display, allowing the driver to override the shutdown feature.
Press the button again to switch the engine off.
Note: Your intelligent access transmitter must be inside the vehicle for
the ignition to start. Keyless warning alert sounds the horn twice when
you exit the vehicle with the intelligent access transmitter and the
keyless vehicle is on.
page 7page 6
9
11
ABC
13 INTEGRATED TRAILER BRAKE
CONTROLLER* assists in smooth and effective
trailer braking by powering the trailer’s electric or
electric over hydraulic brakes with a proportional
output based on the towing vehicle’s
brake pressure.
Use the GAIN adjustment buttons to increase or
decrease the braking feature’s power output to the
trailer. Adjust the GAIN by:

A. Pressing the GAIN + or GAIN – buttons
to increase or decrease the setting to the
desired starting point. A GAIN setting
of 6.0 is a good starting point for
heavier loads.

B. Testing the adjusted GAIN setting.
1. In a traffic-free environment, tow the
trailer on a dry, level surface at a speed of
20-25 mph (30-40 km/h) and squeeze the
manual control lever completely.
2. If the trailer wheels lock up (the tires will
squeal), reduce the GAIN setting. If the trailer
wheels turn freely, increase the
GAIN setting.
3. The proper GAIN setting will be at the point
just below trailer wheel lock-up. If towing a
heavier trailer, trailer wheel lockup may not
be attainable even with the maximum GAIN
setting of 10.
For more information, please refer to the Towing
chapter in your Owner’s Manual.
12
9
10
13
*if equipped *if equipped