ABS FORD EXPLORER 1996 2.G User Guide
[x] Cancel search | Manufacturer: FORD, Model Year: 1996, Model line: EXPLORER, Model: FORD EXPLORER 1996 2.GPages: 444, PDF Size: 3.77 MB
Page 394 of 444
![FORD EXPLORER 1996 2.G User Guide 394
*
[SV46300(ALL)03/95]
Removing the headlamp bulb
*
[SV46400(ALL)01/95]1.
Make sure that the headlamp switch is in the OFF position.
[SV46501( X)05/95]2.
Lift the hood, open the hinged headlamp cov FORD EXPLORER 1996 2.G User Guide 394
*
[SV46300(ALL)03/95]
Removing the headlamp bulb
*
[SV46400(ALL)01/95]1.
Make sure that the headlamp switch is in the OFF position.
[SV46501( X)05/95]2.
Lift the hood, open the hinged headlamp cov](/img/11/4952/w960_4952-393.png)
394
*
[SV46300(ALL)03/95]
Removing the headlamp bulb
*
[SV46400(ALL)01/95]1.
Make sure that the headlamp switch is in the OFF position.
[SV46501( X)05/95]2.
Lift the hood, open the hinged headlamp cover, and behind
the headlamp remove the electrical connector by grasping
the wires and pulling rearward.
*
[SV46700(ALL)04/95]3.
Remove the bulb retaining ring by turning it 1/8 of a turn to
free it from the socket. Then slide the ring off the plastic
base.Keep the ring.You must use it again to hold the new
bulb in place.
*
[SV46800(ALL)04/95]4.
Carefully remove the bulb assembly from its socket by
gently pulling it rearward without turning.
*
[SV46900(ALL)03/95]
Installing the headlamp bulb
*
[SV47000(ALL)02/95]1.
With the flat side of the bulb's plastic base facing upward,
insert the glass end of the bulb into the socket. You may
need to turn the bulb left or right to line up the grooves in
the plastic base with the tabs in the socket. When the
grooves are aligned, push the bulb into the socket until the
plastic base contacts the rear of the socket.
*
[SV47100(ALL)08/95]2.
Slip the bulb retaining ring over the plastic base until it
contacts the rear of the socket. Lock the ring into the socket
by rotating it clockwise until you feel a ªstop.º
*
[SV47200(ALL)02/95]3.
Push the electrical connector into the rear of the plastic base
until it snaps, locking it into position.
*
[SV47300(ALL)02/95]4.
Turn the headlamps on and make sure that they work
properly. If the headlamp was correctly aligned before you
changed the bulb, you should not need to align it again.
File:15unsvx.ex
Update:Thu Feb 29 09:20:34 1996
Page 421 of 444

Index
421
A
Accessory position on the ignition............. 67
Accessory power source, power point outlet....... 204
Additives, engine oil.................. 348
Air bag supplemental restraint system
and child safety seats..............26±27, 52
description.................... 24,28
disposal....................... 32
driver air bag................... 24,28
indicator light..................... 83
operation....................... 28
passenger air bag................. 26,28
proper seating.................... 26
service and information labels............. 28
tone generator.................. 30,32
wearing safety belts.................. 25
Air cleaner filter
location...................... 336
specifications.................... 405
Air suspension, check air ride system warning,
message center................. 100
Alarm, activating remote personal............ 162
All wheel drive.................... 258
Ambulance packages................... 5
Antenna, radio (see Electronic sound system). . . 207, 213, 241
Antifreeze (see Engine coolant)............. 352
Antifreeze (see Engine coolant)............. 352
Anti-lock brake system (ABS)
description..................... 261
noise........................ 263
see also Brake.................... 261
Anti-theft system
arming the system.................. 167
description..................... 167
disarming an untriggered system........... 168
disarming a triggered system............. 168
File:unixx.ex
Update:Thu Feb 29 09:21:09 1996