trailer FORD EXPLORER 1996 2.G User Guide

Driving Your Explorer
289
%*
[DR36600(ALL)01/93]
Hitches
*
[DR36800(ALL)12/91]
Do not install a single or multi-clamp type bumper hitch, or a
hitch which attaches to the axle. Underbody mounted hitches
are acceptable if installed properly. Follow towing instructions
of a reputable rental agency.
*
[DR37000(ALL)12/92]
Whenever a trailer hitch and hardware are removed, make sure
all mounting holes in the underbody are properly sealed to
prevent noxious gases or water from entering.
[DR37100( X)01/95]
Trailer tow/step bumper
[DR37150( X)03/93]
The rear bumper has an integral hitch and only requires a ball
with a 3/4 inch shank diameter. The bumper has a Class II
capability (3500 lb/1590 kg trailer weight and 350 lb/159 kg
tongue weight).
[DR37250( X)01/95]
Use a frame mounted weight distributing hitch for trailers over
3,500 lb. (1590 kg).
*
[DR37550(ALL)03/91]
NOTE: The rated capacities (as shown in this guide) for
trailer towing with the factory bumper are only valid
when the trailer hitch ball is installed directly into the
ball hole in the bumper. Addition of bracketry to
either lower the hitch ball position or extend the hitch
ball rearward will significantly increase the loads on
the bumper and its attachments. This can result in the
failure of the bumper or the bumper attachments. Use
of any type of hitch extensions should be considered
abuse.
*
[DR37575(ALL)03/91]
If it is necessary to relocate the trailer hitch ball position a
frame mounted trailer hitch must be installed.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

290
%*
[DR37800(ALL)07/95]
Safety Chains
[DR37925( X)03/93]
Located near the step bumper hitch ball position are two holes
in the underside of the hitch plate for a Class II trailer (max).
These holes may be used for safety chain attachment when
towing with the step bumper. Always use safety chains when
towing. Safety chains are used to retain connection between the
towing and towed vehicle in the event of separation of the
trailer coupling or ball. Cross the chains under the trailer tongue
and allow slack for turning corners. Connect the chain to the
hitch plate using a positive coupling, such as ªQuick Linksº,
with a strength rating of at least that of the safety chain rating.
[DR37950( X)12/92]
When using a frame mounted trailer hitch, do not attach the
safety chains to the step bumper. Attach the safety chains to the
frame mounted hitch using the recommendations supplied by
the hitch manufacturer.
%*
[DR38000(ALL)08/95]
Trailer Brakes
*
[DR38100(ALL)03/95]
Separate trailer brakes are required on most towed vehicles
weighing over 1,500 lb (680 kg).
*
[DR38200(ALL)05/95]
RWARNING
Do not connect a trailer's hydraulic brake system directly
to your vehicle's brake system. Your vehicle may not
have enough braking power and your chances of having
a collision greatly increase.
%*
[DR38300(ALL)06/95]
Trailer Lamps
*
[DR38400(ALL)11/89]
Make sure your trailer lamps conform to Federal and local
regulations.
*
[DR38425(ALL)03/91]
Class I and Class II Trailer Tow electrical wiring provides two
circuits (right hand and left hand) to operate trailer stop/turn
tail lamps. Each stop/turn circuit will operate one combination
stop/turn light bulb (# 1157, 3157, 2357, or 3357) on the trailer.
Never add more than one trailer light bulb to one circuit.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

Driving Your Explorer
291
*
[DR38450(ALL)08/95]
RWARNING
Always replace a fuse with one that has the specified
amperage rating. Using a fuse with a higher amperage
rating can cause severe wire damage and could start a
fire.
*
[DR38500(ALL)06/95]
Driving while you tow
*
[DR38520(ALL)05/95]
Be especially careful when driving while you tow a trailer.
Never drive faster than 45 mph (70 km/h) when you tow in
hilly country on hot days. Also, anticipate stops so that you can
brake gradually.
%*
[DR38540(ALL)01/95]
If you use the speed control while you are towing on very long,
steep grades, the speed control may shut off.
[DR38600(ALL)12/95]
When towing a trailer in hilly terrain, with a vehicle equipped
with a 4R44E/4R55E/4R70W transmission, you may wish to
operate in O/D OFF (3rd gear) rather than
j(Overdrive). This
will eliminate excessive downshifting and upshifting to maintain
speed. Shift back to
j(Overdrive) whenever practical for
optimum powertrain cooling and fuel economy. This can be
accomplished by pushing in the transmission control switch
which is located on the end of the gearshift lever.
*
[DR38800(ALL)06/95]
When descending a steep grade with a trailer, operate in Drive
rather than Overdrive. If additional braking is needed, shift the
automatic transmission gearshift into 2 (Second) gear or 1 (Low).
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

292
*
[DR38925(ALL)08/95]
Servicing Your Vehicle If You Tow
*
[DR38950(ALL)08/93]
If you tow a trailer for a long distance, your vehicle will need
to be serviced more frequently than usual. Refer to the
Maintenance Schedule and Recordbooklet for additional
information.
[DR39000(ALL)08/95]
Trailer towing tips
*
[DR39100(ALL)11/89]
Before starting on a trip, practice turning, stopping and backing
in an area away from heavy traffic. Get to know the ªfeelº of
the vehicle/trailer combination.
*
[DR39200(ALL)05/90]
Practice backing up. Back up very slowly, with someone outside
at the rear of your trailer to guide you. Place your hand at the
bottom of the steering wheel and move it in the direction you
want the rear of the trailer to swing. Slight movement of the
steering wheel results in a much larger movement of the rear of
the trailer.
*
[DR39300(ALL)11/89]
Allow more room for stopping with a trailer attached. Trailer
brakes should be applied first, whether manually or
automatically controlled, when approaching a stop.
*
[DR39400(ALL)11/89]
For a good handling truck-trailer combination, the trailer tongue
load should be approximately 10-15% of the loaded trailer
weight.
*
[DR39500(ALL)05/95]
Make a thorough check of your equipment before starting out
on the road. After you have traveled about 50 miles (80 km)
stop in a protected area and double-check your hitch and
electrical connections. Also check trailer wheel lug nuts for
tightness.
*
[DR39600(ALL)11/89]
When turning, drive slightly beyond the normal turning point
so the trailer wheels will clear curbs or other obstructions.
[DR39750(ALL)01/95]
When stopped in traffic for long periods of time in hot weather,
place the gearshift selector lever in P (Park) to increase the
engine idle speed. This aids in engine cooling and air
conditioner efficiency. If the engine overheats, rotate the
function selector control knob to panel position to stop the
compressor and increase the engine speed for a short time.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

Driving Your Explorer
293
*
[DR39900(ALL)05/90]
Vehicles with trailers should not be parked on a grade.
However, if you must park on a grade, place wheel chocks
under the trailer's wheels as follows:
*
[DR40000(ALL)05/95]
n
Apply the brake pedal and hold.
*
[DR40100(ALL)11/89]
n
Have another person place the wheel chocks under the
trailer wheels.
*
[DR40200(ALL)08/95]
n
With the chocks in place, release the brake pedal, making
sure the chocks are holding.
*
[DR40300(ALL)03/91]
n
For automatic transmissions Ð apply the parking brake by
pressing the service brake pedal down firmly with your right
foot while applying the parking brake pedal with your left
foot.
[DR40400(ALL)01/95]
n
For manual transmissions Ð apply the service brake and
shift into N (Neutral) while still maintaining pressure on the
service brake pedal. Set the parking brake fully.
*
[DR40500(ALL)12/91]
n
Shift an automatic transmission into Park (P). Put the
gearshift of a manual transmission in Reverse. If your vehicle
is equipped with four-wheel drive make sure the transfer
case is not in Neutral.
*
[DR40600(ALL)01/93]
To start, after being parked on a grade:
*
[DR40700(ALL)05/95]
n
Apply the brake pedal and hold.
*
[DR40800(ALL)08/95]
n
Start the engine.
*
[DR40900(ALL)08/95]
n
Shift transmission into gear and release the parking brake.
*
[DR41000(ALL)08/95]
n
Release the brake pedal and move the vehicle uphill to free
the wheel chocks.
*
[DR41100(ALL)05/95]
n
Apply the brake pedal and hold while another person
retrieves the chocks.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

300
[RE04150(ALL)12/95]
It is not recommended that vehicles equipped with 4WD be
operated in the 4WD modes with a temporary spare. If 4WD
operation is necessary, do not operate at speeds above 10 mph
(16 km/h) or for distances above 50 miles (80 km). Extended
operation in 4WD with a temporary spare may result in damage
to powertrain components.
*
[RE04200(ALL)01/93]
RWARNING
If you use the temporary spare tire continuously or do
not follow these precautions, the tire could fail, causing
you to lose control of the vehicle, possibly injuring
yourself or others.
*
[RE04275(ALL)05/95]
RWARNING
To avoid injury, never run the engine with one wheel off
the ground, such as when changing a tire.
*
[RE04280(ALL)10/94]
Extended use of other than matching size spare tires on a
Traction-Lok axle could result in a permanent reduction in
effectiveness. This loss of effectiveness does not affect normal
driving and should not be noticeable to the driver.
*
[RE04300(ALL)01/95]
When you drive with the temporary spare tire, DO NOT:
*
[RE04400(ALL)01/95]
n
exceed 50 mph (80 km/h) under any circumstances.
*
[RE04500(ALL)01/95]
n
load your vehicle so that it is heavier than the maximum
vehicle load rating listed on the tire decal.
*
[RE04600(ALL)01/95]
n
tow a trailer.
*
[RE04700(ALL)01/95]
n
use tire chains on this tire.
*
[RE04800(ALL)01/95]
n
try to repair the temporary spare tire or remove it from its
wheel.
*
[RE04900(ALL)01/95]
n
use the wheel for any other type of vehicle.
[RE04950(ALL)10/94]
n
engage four-wheel drive on dry, hard-surfaced roads.
File:12unrex.ex
Update:Thu Feb 29 09:14:34 1996

374without having to drive 20 miles to obtain a normal operating
temperature if outside temperatures are above50ÊF (10ÊC).
*
[SV33801(ALL)01/95]
NOTE: If the vehicle has been operated for an extended
period at high speeds or in city traffic during hot
weather, or pulling a trailer, the vehicle should be
turned off for about 30 minutes to allow the fluid to
cool before checking.
%*
[SV33901(ALL)02/95]
Checking the Automatic Transmission Fluid
*
[SV33910(ALL)06/95]
With the vehicle on a level surface, start the engine and move
the transmission shift selector through all of the gear ranges
allowing sufficient time for each position to engage. Securely
latch the transmission shift selector in the P (Park) position,
fully set the parking brake and leave the engine running.
*
[SV33930(ALL)10/89]
RWARNING
Your vehicle should not be driven if the fluid level is
below the bottom hole on the dipstick and outside
temperatures are above50ÊF (10ÊC).
*
[SV33940(ALL)08/95]
Wipe off the dipstick cap (located on the passenger's side of the
engine), pull the dipstick out and wipe the indicator end clean.
Put the dipstick back into the filler tube and make sure it is
fully seated. Pull the dipstick out and read the fluid level.
*
[SV33950(ALL)03/90]
When checking fluid at normal operating temperature, the fluid
level should be within the crosshatched area on the dipstick.
When the vehicle has not been driven, and outside temperature
is above50ÊF (10ÊC), thefluid level should be between the holes
on the dipstick.
File:15unsvx.ex
Update:Thu Feb 29 09:20:34 1996

423
Index
Brake fluid
brake warning light.................. 81
checking and adding................ 377
description..................... 377
specifications.................... 406
Brakelamp, high-mount brakelamp........... 134
Brakes
adjustment..................... 261
anti-lock...................... 261
applying the brakes................. 265
brake warning light.................. 81
fluid, checking and adding.............. 377
fluid, refill capacities................ 377
fluid, specifications................. 406
front disc...................... 261
if brakes do not grip well.............. 264
master cylinder................... 377
new brake linings................... 5
noise........................ 261
parking...................... 266
power braking................... 261
servicing....................264, 377
stopping distances................265, 267
trailer....................... 290
when storing your vehicle.............. 410
Brake-shift interlock.................. 247
Break-in period..................... 5
Brights (high beams).................91,136
Built-in child seat
cleaning....................... 52
operation....................... 34
Bulbs, replacing.................... 392
halogen...................... 393
headlamps..................... 393
File:unixx.ex
Update:Thu Feb 29 09:21:09 1996

426
Convenience kit in cargo area............. 301
Coolant (see Engine coolant)
checking and adding................ 352
drain and flush................... 356
preparing for storage................ 410
refill capacities................... 356
specifications.................... 406
temperature gauge.................. 92
warnings...................... 352
Cooling fan...................... 334
Crankcase emission filter................ 405
Cruise control (see Speed control)............ 141
Customer Assistance Centre, Ford of Canada...... 324
D
Dashboard (see Instrument panel)............ 109
Daytime running light system............. 132
Defects, reporting................... 323
Defrost
rear window.................... 126
windshield..................... 113
Dipstick....................... 349
automatic transmission fluid...........373, 375
engine oil..................... 349
power steering fluid................. 379
Disabled vehicle (see Towing)............. 311
Dispute Settlement Board............... 319
Doors........................ 147
lubricant specifications................ 406
Driveline universal joint and slip yoke......... 377
Driving under special conditions
bad weather.................... 269
heavy load..................... 271
high speed..................... 268
high water..................... 270
slippery roads................... 269
tips for safe driving................. 267
towing a trailer................... 272
File:unixx.ex
Update:Thu Feb 29 09:21:09 1996

434
Lamps (continued)
interior lamps.................127, 132
replacing bulbs................... 392
trailer....................... 290
Lane change indicator (see Turn signal)......... 135
Lights, warning and indicator
airbag........................ 83
anti-theft....................... 88
brake........................ 81
charging system................... 87
check engine..................... 84
engine oil pressure.................. 90
hazard warning light................ 139
high beam...................... 91
low washer fluid.................. 104
oil pressure...................... 90
overdrive off..................... 86
safety belt...................... 82
service engine soon.................. 84
theft system..................... 88
turn signal indicator................. 135
Load limits
GAWR....................... 271
GVWR....................... 271
trailer towing.................... 272
Lubricant specifications................ 406
Lug nuts
standard...................... 307
tightening sequence................. 304
M
Maintenance schedule and record (see separate Maintenance
Schedule and Record booklet)........... 3
Maintenance (see Servicing).............. 333
Manual transmission
clutch.....................251, 376
fluid, checking and adding.............. 376
lubricant specifications................ 406
File:unixx.ex
Update:Thu Feb 29 09:21:09 1996