warning light FORD EXPLORER 1996 2.G Owner's Manual

Warning Lights and Gauges
99
*
[LG36050( X)01/95]
Because of factors like rounding of numbers and fuel movement
in the tank, the M/C and the service station fuel pump readings
may disagree slightly.
%*
[LG36100( X)05/95]
Fuel Economy
[LG36150( X)10/94]
A press of the FUEL ECON switch allows you to display one of
two features (Average Fuel Economy or Instantaneous Fuel
Economy). The first press of the FUEL ECON switch will allow
you to display your average fuel economy in miles/gallons or
liters/kilometers. Your M/C computes this figure using the
distance traveled and fuel used information. If you want to reset
this feature, press the RESET switch while the average fuel
economy feature is displayed. Your average fuel economy will
then use data only from after the RESET was pressed to
calculate the new average.
[LG36200( X)10/94]
A second consecutive press of the FUEL ECON switch will
allow you to display the instantaneous fuel economy, which is
the fuel economy that you get at any particular moment. For
example, you can see what your fuel economy is in heavy traffic
or on an open highway. Your fuel economy is affected by such
factors as braking, acceleration, and the type of road you are
driving on.
*
[LG36250( X)01/95]
Your vehicle must be moving for the M/C to calculate the fuel
economy. When your vehicle is not moving, instantaneous fuel
economy will be displayed at 0 miles/gallon or
99 kilometers/100 liters. When you are moving, the M/C will
display between 0 and 99 miles/gallon or between 1 and
99 kilometers/100 liters.
*
[LG36300( X)01/95]
Reset
[LG36350( X)01/95]
A press of the RESET switch will allow you to reset the current
feature being displayed. Warnings, Distance Driven, Average
Fuel Economy, Fuel Used, and your Personalized Oil Reset
Percentage are the only features which respond to the RESET
switch. Distance to Empty, Fuel Remaining, and Instantaneous
File:05unlgx.ex
Update:Thu Feb 29 09:04:08 1996

Warning Lights and Gauges
101 for service as soon as possible. For Fuel Level, the first message
will indicate the fuel level status (OK or LOW) and the second
message will indicate the range (distance to empty).
*
[LG37500( X)01/95]
Message center operation during system check
*
[LG37550( X)01/95]
The M/C switches will operate as follows during the System
Check sequence:
*
[LG37600( X)01/95]1.
A press of the SYSTEM CHECK switch will advance the
cycle to the next system message without waiting the two
seconds.
*
[LG37650( X)01/95]2.
A press of the RESET switch anytime during this sequence
will cause the SYSTEM CHECK cycle to conclude
immediately and the last displayed feature before pressing
SYSTEM CHECK will be displayed.
[LG37700( X)04/94]3.
A press of the RANGE, FUEL STATUS, OR FUEL
ECONOMY, switch will conclude the SYSTEM CHECK cycle
and the requested feature will be displayed.
*
[LG37750( X)01/95]4.
A press of the ENGLISH/METRIC switch will halt the
SYSTEM CHECK cycle and display, in the new mode, the
last displayed feature before pressing the SYSTEM CHECK
switch.
*
[LG37800( X)01/95]5.
A press of the OIL CHANGE RESET switch during the
sequence will cause the SYSTEM CHECK cycle to conclude
and the Oil Change Reset Procedure will begin.
*
[LG37850( X)01/95]
System Warnings
[LG37900( X)01/95]
System warnings alert you to possible problems or malfunctions
in your vehicle's operating systems. There are twelve warning
messages which can be displayed by the Message Center (M/C)
to show the status of the monitored systems. When a warning
occurs, the warning message is displayed and a tone sounds.
The warning message will appear at a brighter level if the
instrument panel is dimmed.
File:05unlgx.ex
Update:Thu Feb 29 09:04:08 1996

Warning Lights and Gauges
103
*
[LG38150( X)01/95]
The following is a list of warning messages and their associated
reset category:
[LG38200( X)04/94]
fourteen pica
chart:0021147-A*
[LG38250( X)01/95]
Check Engine Temp
*
[LG38300( X)01/95]
This warning message is displayed when the engine coolant is
overheating. Stop the vehicle as soon as safely possible, turn off
engine and let it cool. Check the coolant and level following the
instructions in theServicing Your Vehiclechapter. If you do not
follow these instructions, you or others could be injured.
*
[LG38350( X)01/95]
Check Charging System
*
[LG38400( X)03/95]
This warning message is displayed when the electrical system is
not maintaining a proper voltage. If you are running electrical
accessories when the engine is idling at a low speed, turn off as
many of the electrical loads as soon as safely possible. If this
warning stays on or comes on when the engine is operating at
normal speeds, have the electrical system checked as soon as it
is safely possible.
File:05unlgx.ex
Update:Thu Feb 29 09:04:08 1996

104
*
[LG38450( X)01/95]
Low Fuel Level
*
[LG38500( X)01/95]
This warning message is displayed when you have
approximately 50 miles (80 km) left before you run out of fuel.
*
[LG38550( X)01/95]
Low Oil Level
*
[LG38600( X)01/95]
This warning message is displayed when your engine oil level is
low. If this warning message is displayed, check the level of the
engine oil.
*
[LG38650( X)02/95]
To check your oil:
*
[LG38700( X)05/95]1.
Park your vehicle on level ground, turn off the engine and
wait at least 5 minutes for the oil to drain back into the oil
pan.
*
[LG38750( X)01/95]2.
Use the dipstick to check the oil. If the level is low, add oil,
but do not overfill.
*
[LG38800( X)01/95]
If you are parked on a steep incline, the LOW OIL LEVEL
warning may come on when you start your vehicle, even
though the oil is at the correct level.
*
[LG38850( X)01/95]
For information about adding oil, seeEngine oilin the Index.
%*
[LG38900( X)05/95]
Low Washer Fluid Light
*
[LG38950( X)04/95]
This warning message is displayed when the washer fluid
reservoir is less than one quarter full.
[LG39000( X)01/95]
Check Head Lamps
[LG39050( X)08/94]
This warning message is displayed when you turn on your
headlamps and at least one of them is burned out. A high beam
headlamp burn out is not monitored.
[LG39100( X)04/94]
Check Tail Lamps
[LG39150( X)04/94]
This warning message is displayed when you turn on your rear
parking (tail) lamps and at least one of them is burned out.
File:05unlgx.ex
Update:Thu Feb 29 09:04:08 1996

Warning Lights and Gauges
105
[LG39200( X)04/94]
Check Brake Lamps
[LG39250( X)03/95]
This warning message is displayed when you turn on your
brakelamps by pressing the brake pedal and at least one of the
lamps is burned out.
[LG39300( X)04/94]
If you use additional lights, such as trailer lights, or if you
replace the headlamps or bulbs with equipment that is not equal
to the original equipment from Ford, you may get a false
ªCHECK LAMPSº warning or no warning at all.
[LG39350( X)06/94]
Air Ride Switch Off (If equipped)
[LG39400( X)03/95]
This warning message is displayed when the air suspension
switch, located in the rear jack stowage area on the left side, is
off. For information about the operation of the air suspension
switch, seeAutomatic ride control systemin the Index.
[LG39450( X)06/94]
Check Air Ride System (If equipped)
[LG39500( X)03/95]
This warning message is displayed when an air suspension
system fault has been detected. If this warning message is
displayed while driving, safely pull off the road at your earliest
convenience. If the vehicle is loaded beyond the recommended
maximum payload, the CHECK AIR RIDE SYSTEM message
may be displayed. This is a normal condition if the vehicle is
overloaded. To correct this condition, remove or redistribute the
payload per the recommended maximum requirements. Turn the
ignition switch from ON to OFF and ON again. If the warning
message reappears, turn the air suspension switch (located in
the rear jack stowage area on the left side) OFF and take your
vehicle to a dealership for service as soon as possible.
*
[LG39550( X)01/95]
Change Oil Soon or Oil Change Required
*
[LG39600( X)01/95]
One of these warning messages is displayed when the engine oil
life remaining is 5% or less. When Oil Life Left is between 5%
and 0%, the ªCHANGE OIL SOONº message will be displayed.
When Oil Life Left reaches 0%, the ªOIL CHANGE REQUIREDº
message will be displayed.
File:05unlgx.ex
Update:Thu Feb 29 09:04:08 1996

Warning Lights and Gauges
107
[LG40301( X)08/94]3.
Press the RESET switch to complete the procedure. A press
of any switch besides RESET or OIL CHANGE RESET will
abort this procedure and will not establish your new
Personalized Oil Reset Percentage.
[LG40401( X)08/94]
When your Personalized Oil Reset Percentage has been
established, it will be used beginning with the completion of
your next OIL CHANGE RESET procedure.
File:05unlgx.ex
Update:Thu Feb 29 09:04:08 1996

132
%*
[IP17780(ALL)08/95]
Cleaning the Exterior Lamps
*
[IP17785(ALL)08/95]
Do not use dry paper towel, chemical solvents or abrasive
cleaners to clean the lamps, as these may cause scratches or
crack the lamps.
%*
[IP17815(ALL)01/95]
Daytime Running Light System
*
[IP17820(ALL)03/95]
(Canadian vehicles only)
*
[IP17830(ALL)03/95]
The Daytime Running Light (DRL) system turns the high beam
headlamps on, with a reduced light output, when:
*
[IP17840(ALL)03/95]
n
The headlamp system is in the OFF position, and
*
[IP17850(ALL)01/95]
n
The vehicle has a fully released parking brake.
*
[IP17860(ALL)05/95]
The high beam indicator light on the instrument cluster will not
be on.
*
[IP17890(ALL)05/95]
RWARNING
The Daytime Running Light (DRL) system will not
illuminate the tail lamps and parking lamps. Turn on
your headlamps at dusk. Failure to do so may result in a
collision.
%*
[IP17900(ALL)03/95]
Lighting Up the Instrument Panel and the Interior of
Your Vehicle
[IP18000(ALL)10/94]
The instrument panel lights can be turned on by turning the
headlamp knob toward either the first or second position. You
can brighten or dim the instrument panel lights by rotating the
thumb wheel.
[IP18200(ALL)03/95]
The interior lights will shut off after 25 seconds with all the
doors closed, or immediately when the ignition switch is turned
to the ON position, or if the vehicle speed is above five MPH
(8 km/h). The interior lights will turn off after 40 minutes if
any of the doors are left open. Refer toBattery Saverin the
Featuressection for more details.
File:06unipx.ex
Update:Thu Feb 29 09:05:45 1996

138
[SC05502(ALL)10/94]
Gearshift Lever (Automatic transmission
only)
[SC05504( X)08/94]
The gearshift lever on your Explorer is mounted on the steering
column. On the end of the gearshift lever is the Overdrive
On/Off button. For additional information about the gearshift
lever and the Overdrive On/Off button, see theDriving Your
Explorerchapter.
[SC05508(ALL)10/94]
7-1/2 pica art:0021255-A*
[SC05510(ALL)11/93]
OVERDRIVE OFF Lamp
[SC05512(ALL)03/95]
This lamp indicates the operating range of the transmission.
This lamp illuminates when the O/D ON/OFF button is
depressed. For additional information, refer to theWarning
Lights and Gaugeschapter.
[SC05514(ALL)07/95]
6 pica art:0021226-BFile:07unscx.ex
Update:Thu Feb 29 09:06:35 1996

Steering Column Controls
143
*
[SC08700(ALL)08/95]
RWARNING
Do not use the speed control in heavy traffic or on roads
that are winding, slippery, or unpaved.
*
[SC08801(ALL)05/95]
In mountainous areas, at higher elevations, or when pulling a
trailer, the speed control may not be able to maintain the preset
speed with the transmission in
j(Overdrive).
*
[SC08850(ALL)06/92]
If your vehicle comes with a 5-speed manual transmission, you
may prefer to drive in 4 (Fourth) gear, in mountainous areas or
at high altitudes, to improve speed control performance.
*
[SC09275(ALL)12/91]
In order to downshift (with a manual transmission) with the
speed control operating, you must press either the brake or
clutch pedal long enough to disengage the speed control. Wait a
second before depressing the clutch again and making the shift
so that the speed control can fully return to the idle position.
*
[SC09325(ALL)05/95]
RWARNING
Do not shift the transmission into N (Neutral) with the
speed control on.
[SC09350(ALL)03/95]
To maintain a preset speed under the above conditions, with
electronically controlled transmissions Ð press the Transmission
Control Switch (TCS). The indicator light will turn on and
illuminate the words ªO/D OFF.º This will cancel ªOverdrive.º
You can press the Transmission Control Switch (TCS) on or off
at any speed. For the best fuel economy during normal driving
conditions, press the Transmission Control Switch (TCS) to turn
off the light. This allows overdrive operation.
File:07unscx.ex
Update:Thu Feb 29 09:06:35 1996

146
%*
[SC11500(ALL)08/95]
Cancelling and Resuming a Set Speed
*
[SC11600(ALL)06/95]
If you press the brake pedal, the speed control is cancelled. You
can return to the speed you set by using the RSM switch, as
long as you did not press the OFF switch.
*
[SC11700(ALL)08/95]
To resume the speed you had before, you must be driving at
least 30 mph (50 km/h).
*
[SC11800(ALL)05/93]
Press and release the RSM switch. Your vehicle gradually
returns to the previously set speed and then maintains it.
*
[SC11850(ALL)03/95]
RWARNING
If your vehicle has speed control, do not use it on
slippery roads. You could lose control of your vehicle
and could injure someone.
[SC12000( X)06/95]
Speed Control Indicator (If equipped)
[SC12100( X)08/94]
A SPEED CONTROL light is displayed in the instrument cluster
when the speed control system is engaged. The display will turn
off when the brake pedal is pressed or if speed control is shut
off.
*
[SC12200( X)05/95]
This display does not indicate any problems with the speed
control, but is simply a convenient way of knowing when it is
active.
File:07unscx.ex
Update:Thu Feb 29 09:06:35 1996