engine FORD EXPLORER 1996 2.G Owner's Guide

126
%*
[IP12300( X)06/95]
Rear Window Defroster (If equipped)
*
[IP12400( X)12/91]
The defroster for the rear window clears frost, fog, or thin ice
from both the inside and outside of the rear window.
[IP12500( X)10/94]
The control switch is located on the instrument panel to the
right of the radio.
[IP12700( X)08/94]
7-1/2 pica art:0020110-H
Rear window defroster switch
*
[IP12800( X)02/95]
To defrost the rear window:
*
[IP12900( X)02/95]1.
Clear any snow from the rear window.
*
[IP13000( X)09/93]2.
Get in your vehicle and start the engine.
[IP13200( X)06/94]3.
Push the switch and release. The indicator light turns on.
Push switch again to turn off.
*
[IP13300( X)02/05]
The defroster turns off automatically after approximately 10
minutes. If the window is not clear, turn on the defroster again.
It will also automatically shut off any time the engine is shut
off.
%*
[IP13400( X)09/95]
NOTE: Never use sharp instruments or window cleaners with
abrasives to clean the inside of your rear window. If
you do, you may damage the heating elements that
are bonded to the inside of the rear window and
cause damage to the rear window defroster.
File:06unipx.ex
Update:Thu Feb 29 09:05:45 1996

166
%*
[FV18101(ALL)02/95]
Replacing lost transmitters
[FV18200(ALL)07/95]
In the event a transmitter is lost, you should take your vehicle's
transmitters to your dealer to have the remote entry system
deprogrammed for the lost transmitter. This is necessary to
prevent further unauthorized use of the lost transmitter.
*
[FV18301(ALL)02/95]
You can also purchase additional transmitters (up to 4
transmitters can be used) from your dealer. You will need to
take all your transmitters to the dealer so they can program
them to the remote entry system all at the same time.
%*
[FV18601(ALL)04/95]
Illuminated Entry System (If equipped)
*
[FV18701(ALL)06/95]
This system will provide illumination of the vehicle's interior
courtesy lamps when either outside front door handle is pulled
or when the remote entry system is used to unlock the door or
sound the personal alarm. The system will automatically turn
off after approximately 25 seconds or when the ignition is
turned to the RUN or ACC position.
*
[FV18801(ALL)09/95]
NOTE: The inside lights will not turn off if you have turned
them on with the dimmer thumbwheel or if any door
is open.
[FV18810( X)10/94]
Delayed Accessory
[FV18815( X)08/94]
This feature provides power to operate the power windows and
power moon roof for 10 minutes after the ignition switch is
turned from the RUN to the OFF position.
[FV18820( X)06/94]
If either front door is opened during the 10 minute period the
delayed accessory feature will be disabled.
%*
[FV18900(ALL)08/94]
Battery Saver
*
[FV19000(ALL)03/95]
When the ignition is turned off, the vehicle will turn off battery
voltage to all of these lights after 40 minutes: glove box, engine
compartment, overhead console, mirror, courtesy and
interior (including cargo) lamps.
File:08unfvx.ex
Update:Thu Feb 29 13:56:40 1996

245
Driving Your Explorer
*
[DR00350(ALL)06/95]
Procedures for driving your vehicle will vary depending on
which type of transmission your vehicle has.
*
[DR00600(ALL)06/95]
n
a manual transmission
[DR05475( X)12/95]
n
an Automatic Overdrive Transmission 4R55E or 4R70W
[DR05700(ALL)1/96]
Automatic Transmission Operation
4R44E/4R55E/4R70W
*
[DR08715(ALL)12/95]
The 4R44E, 4R55E and 4R70W transmissions are electronically
controlled four speed overdrive automatic transmissions with
lockup torque converter. Transmission operation is controlled by
the Powertrain Control Module (PCM).
*
[DR08720(ALL)08/95]
The PCM will automatically adjust transmission operation to
make up for varying conditions. Several sensors located on the
engine and transmission such as throttle position, engine speed,
vehicle speed and transmission temperature are used by the
PCM to shift the transmission into a higher or lower gear when
required for the best performance and fuel economy. For
example, you may notice that the transmission will upshift to a
higher gear more quickly when the vehicle has not reached
normal operating temperature.
*
[DR08730(ALL)08/95]
The PCM also controls the transmission's Torque Converter
Clutch (TCC) to further raise vehicle performance and fuel
economy. The TCC will engage when the transmission operating
temperature and other conditions determined by the PCM have
been met. Engagement of the clutch may be noted as a decrease
in engine speed.
[DR08740(ALL)03/95]
To help in troubleshooting, the PCM continually performs
self-tests on the electronic control system and, if any faults are
detected, stores them in memory. The Overdrive Off Indicator
Light (O/D OFF), which is located on the instrument cluster,
may flash steadily if a malfunction has been detected. If the
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

248
%*
[DR09200(ALL)01/95]
R (Reverse)
*
[DR09300(ALL)08/95]
With the gearshift in the R (Reverse) position, the vehicle will
move backward. You should always come to a complete stop
before shifting into or out of R (Reverse).
*
[DR09350(ALL)01/95]
N (Neutral)
*
[DR09375(ALL)01/95]
With the gearshift in the N (Neutral) position, the vehicle can be
started and is free to roll. Hold the brake pedal down while in
this position.
%*
[DR09400(ALL)01/95]
Driving
%*
[DR09500(ALL)04/95]
When to use
j(Overdrive)
*
[DR09600(ALL)04/95]
This is the normal driving position. As the vehicle picks up
speed, automatic upshifts to second, third and fourth gears will
occur when
jOverdrive is chosen on the selector and the
transmission control switch has not been pressed. The
transmission will shift into the correct gear when the right
speed is achieved, for the accelerator pedal position you have
chosen.
*
[DR09700(ALL)03/94]
When to use Drive
[DR09800(ALL)06/95]
You will note there is not a drive position on your gearshift
indicator. However, you will find a transmission control switch
labeled O/D ON/OFF located on the end of the gearshift lever.
Press this switch and the O/D OFF indicator light will
illuminate on the instrument cluster. With overdrive cancelled
and the O/D OFF indicator light illuminated, the transmission
will operate in gears one through three. This is useful if you
experience frequent downshift/upshift conditions, when
operating with a heavy load or in hilly terrain, or if additional
engine braking is useful. However, shift back to
j(Overdrive)
whenever practical for optimum powertrain cooling and fuel
economy. This can be accomplished by pushing the transmission
control switch again, to cancel the O/D OFF control and light.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

Driving Your Explorer
249
[DR09850(ALL)01/95]
quarter page
art:0021255-A
Transmission control switch (located on the end of the gearshift lever)
*
[DR09900(ALL)05/95]
To return the transmission to the normal
jOverdrive
operation, press the transmission control switch again. The
Transmission Control Indicator Light will not be illuminated
when Overdrive operation resumes. This switch may be used to
select O/D ON or O/D OFF any time the vehicle is being
driven.
*
[DR09950(ALL)05/94]
When starting your vehicle, the overdrive system will
automatically be in the normal overdrive mode.
*
[DR10100(ALL)01/95]
When to use 2 (Second)
*
[DR10200(ALL)01/95]
Use 2 (Second) to start-up on slippery roads or to provide
additional engine braking on downgrades. This position
provides 2 (Second) gear operation only.
*
[DR10300(ALL)01/95]
When to use 1 (Low)
*
[DR10400(ALL)04/95]
Use 1 (Low) to provide maximum engine braking on steep
downgrades. Upshifts from 1 (Low) can be made by manually
shifting to 2 (Second) or
j(Overdrive). Selection of 1 (Low)
gear provides only low gear operation from start-up. Selection
of 1 (Low) while at higher speeds provides a shift to second
gear, and a shift to first gear will occur after the vehicle
decelerates to the proper speed.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

250
*
[DR10500(ALL)01/95]
P (Park)
*
[DR10600(ALL)03/94]
Always come to a complete stop before you shift into P (Park).
This position locks the transmission and prevents the rear
wheels from turning. To securely latch the gearshift in the P
(Park) position, pull it toward you, push it completely
counterclockwise against the stop, and then push it toward the
instrument panel.
*
[DR10650(ALL)03/94]
The gearshift is securely latched in P (Park) if you cannot rotate
it in a clockwise direction without lifting it toward you.
*
[DR10700(ALL)06/95]
RWARNING
Always set the parking brake fully and make sure the
gearshift is securely latched in P (Park).
*
[DR10800(ALL)06/95]
RWARNING
Never leave your vehicle unattended while it is running.
*
[DR11100(ALL)06/94]
Forced Downshifts
*
[DR11200(ALL)04/95]
To gain extra acceleration injOverdrive or Drive (O/D OFF),
push the accelerator to the floor. The transmission will
automatically downshift to the appropriate gear: third, second
or first.
*
[DR11235(ALL)03/94]
Power Braking
*
[DR11275(ALL)03/94]
Increasing the engine speed above idle without vehicle
movement (such as holding the brake) in a forward or reverse
gear causes transmission stall.
*
[DR11285(ALL)09/95]
NOTE: Continued operation in the stall condition can result
in transmission overheat, malfunction or fluid
expulsion.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

Driving Your Explorer
251
[DR11300(ALL)08/94]
Manual Transmission Operation
%*
[DR11400(ALL)03/95]
Using the Clutch
*
[DR11500(ALL)01/95]
Make sure the gearshift lever is in the N (Neutral) position and
your right foot is holding down the brake pedal. Then press the
clutch pedal to the floor with your left foot. Manual
transmission vehicles have a starter interlock switch. The starter
will not crank until the clutch pedal is fully depressed. Start the
engine and allow it to idle for a few seconds. Move the
gearshift into 1 (First) or R (Reverse).
*
[DR11600(ALL)03/91]
To move the vehicle, release the clutch slowly and at the same
time press down slowly on the accelerator so that the vehicle
accelerates.
*
[DR11700(ALL)03/95]
Do not drive with your foot resting on the clutch pedal and do
not use the clutch to hold your vehicle at a standstill while
waiting on a hill. These actions will seriously reduce clutch life.
*
[DR11750(ALL)03/95]
Driving with your foot resting on the clutch may cause the
vehicle to jerk sharply when pressing or removing your other
foot from the accelerator.
%*
[DR11800(ALL)03/95]
Shifting the Gears
*
[DR11900(ALL)02/95]
The gearshift for a manual transmission is mounted on the floor.
The gearshift pattern consists of seven positions: Neutral, five
forward gears, and Reverse.
[DR12000(ALL)10/94]
7-1/2 pica art:0021180-B
5-Speed Overdrive manual transmission shift pattern
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

Driving Your Explorer
253
%*
[DR13250(ALL)06/95]
Recommended Shift Speeds
[DR14950(ALL)04/94]
Engines with 5-Speed Manual Overdrive Transmission
[DR15000(ALL)10/94]
thirty pica
chart:0021181-DFile:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

254
*
[DR15100(ALL)03/95]
When you slow down or climb a steep hill, always downshift
before the engine starts to lose power. Downshifting reduces the
chance of stalling and gives your vehicle better acceleration to
increase speed again.
*
[DR15200(ALL)03/95]
When you drive down steep hills, downshifting helps you keep
a safe speed and helps prevent unnecessary wear on the brakes.
*
[DR15300(ALL)03/95]
When you come to a stop, do not downshift through each gear.
Disengage the clutch and use the brake as necessary.
Downshifting through the gears decreases your vehicle's fuel
economy.
*
[DR15400(ALL)05/95]
RWARNING
Continued use of a damaged or worn clutch, prolonged
clutch slippage or downshifting at excessive speeds can
result in a failure of the engine, transmission or clutch
components.
*
[DR15500(ALL)03/91]
Transmission Function
[DR15600(ALL)10/94]
Upshift at the speeds specified in the chart. All forward gears
are synchronized allowing you to shift into them with your
vehicle in motion. The clutch pedal should be fully depressed
when shifting.
*
[DR15625(ALL)04/94]
NOTE: Shifting during extremely low rpm's can result in a
momentary audible rattle which disappears as vehicle
rpm's are increased. Shifting at higher speeds will
eliminate this sound.
*
[DR15700(ALL)03/95]
Parking
*
[DR15800(ALL)01/95]
To park your vehicle, apply the service brake pedal, and shift
into N (Neutral) while still maintaining pressure on the service
brake. Set the parking brake fully. Shift into first and turn off
the ignition.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

Driving Your Explorer
255
*
[DR15900(ALL)05/95]
RWARNING
Do not park your vehicle in Neutral, it may move
unexpectedly and injure someone. Use 1 (First) gear and
set the parking brake fully.
%*
[DR15915(ALL)01/95]
Steering Your Vehicle
%*
[DR15945( X)01/95]
Your vehicle comes with power steering. Power steering uses
energy from the engine to help steer your vehicle.
%*
[DR15950(ALL)04/95]
If the amount of effort needed to steer your vehicle changes at a
constant vehicle speed, have the power steering system checked.
If the power steering system breaks down (or if the engine is
turned off), you can steer the vehicle manually but it takes more
effort.
*
[DR15960(ALL)01/95]
Never hold the steering wheel to the extreme right or left for
more than five seconds if the engine is running. This can
damage the power steering pump.
*
[DR15985(ALL)05/90]
NOTE: After any severe impact such as striking large
potholes, sliding into curbs on icy roads, or a collision
involving the front end, observe the steering wheel
alignment. If the spokes of the steering wheel seem to
be in a different position while going straight down
the road, have the front suspension and steering
checked for possible damage.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996