stop start FORD F SERIES MOTORHOME AND COMMERCIAL CHASSIS 1997 10.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1997, Model line: F SERIES MOTORHOME AND COMMERCIAL CHASSIS, Model: FORD F SERIES MOTORHOME AND COMMERCIAL CHASSIS 1997 10.GPages: 224, PDF Size: 1.11 MB
Page 36 of 224
32
*
[CF33300( ALL)01/96]
NOTE: If your speed increases above your set
speed while driving inj(Overdrive)
on a downhill grade, you may want to
depress the transmission control switch
located on the shift lever to turn off
overdrive to reduce vehicle speed.
Speed control cannot reduce the vehicle
speed if it goes above your set speed
on a downhill grade. For the best fuel
economy during normal driving
conditions, leave the shift select inj
(Overdrive), or resume as soon as
practical.
*
[CF33400( ALL)01/96]
RWARNING
Do not use the speed control in heavy
traffic or on roads that are winding,
slippery, or unpaved.
*
[CF33500( ALL)01/96]
In mountainous areas, at higher elevations, or
when pulling a trailer, the speed control may
not be able to maintain the preset speed with
the transmission inj(Overdrive).
*
[CF33800( ALL)01/96]
RWARNING
Do not shift the transmission into N
(Neutral) with the speed control on.
*
[CF33900( ALL)01/96]
To maintain a preset speed under the above
conditions, with electronically controlled
transmissions Ð press the Transmission Control
Switch. The indicator light will turn on and
illuminate the word ªOFF.º This will cancel
ªOverdriveº. You can press the Transmission
Control Switch on or off at any speed. For the
best fuel economy during normal driving
conditions, press the Transmission Control
Switch to turn off the light. This allows
overdrive operation. After the vehicle has been
stopped and the engine has been restarted, the
File:05ltcfm.ex
Update:Thu Dec 12 13:31:05 1996
Page 43 of 224
39 %
*
[TO03000( ALL)01/96]
For a cold engine:
*
[TO03100( ALL)01/96]
q
At temperatures10ÊF (-12ÊC) andbelow:If
the engine does not start infifteen (15)
secondson the first try, turn the key to OFF,
wait approximately ten (10) seconds so you
do not flood the engine, then try again.
*
[TO03200( ALL)01/96]
q
At temperaturesabove10ÊF(-12ÊC):If the
engine does not start infive (5) secondson
the first try, turn the key to OFF, wait
approximately ten (10) seconds so you do not
flood the engine, then try again.
*
[TO03300( ALL)01/96]
q
Do not hold the key in the START position
for more thanfifteen (15) secondsat a time.
%*
[TO03400( ALL)01/96]
For a warm engine:
*
[TO03500( ALL)01/96]
q
Do not hold the key in the START position
for more thanfive (5) secondsat a time. If
the engine does not start within five (5)
seconds on the first try, turn the key to the
OFF position. Wait a few seconds after the
starter stops, then try again.
*
[TO03600( ALL)01/96]
Whenever you start your vehicle, release the key
as soon as the engine starts. Excessive cranking
could damage the starter.
*
[TO03700( ALL)01/96]
After you start the engine, let it idle for a few
seconds. Keep your foot on the brake pedal and
put the gearshift lever in gear. Release the
parking brake. Slowly release the brake pedal
and drive away in the normal manner.
File:08lttom.ex
Update:Fri Dec 13 11:22:15 1996
Page 47 of 224
43
*
[TO07600( ALL)01/96]
If the engine is idling while you are stopped in
an open area for long periods of time, open the
windows at least one inch (2.5 cm). Also, adjust
the heating or air conditioning system to bring
in outside air.
[TO07900( M)01/96]
q
HEATING Ð Set fan speed at MEDIUM or
HIGH, the function selector knob on VENT,
FLOOR, FLR DEF or DEFROST symbol and
the temperature control knob on any desired
position.
[TO08200( M)01/96]
q
AIR CONDITIONING Ð Set the fan speed at
MEDIUM or HIGH, the function selector
lever on NORM or VENT and the
temperature control knob on any desired
position.
[TO08300( M)01/96]
TAPPET NOISE
[TO08400( M)01/96]
It is normal for the oil to drain down from the
hydraulic tappets in your engine during
extended shutdown periods (overnight). As a
result, these tappets may clatter for a few
seconds after the engine starts until oil pressure
builds up. This momentary start-up noise is
normal and is not harmful to engine operation.
File:08lttom.ex
Update:Fri Dec 13 11:22:15 1996
Page 51 of 224
47 %
*
[GF03500( ALL)01/96]
Applying the Brakes
*
[GF03550( ALL)01/96]
Apply the brake pedal gradually. Use the
ªsqueezeº technique Ð push on the brake pedal
with a steadily increasing force. This allows the
wheels to continue to roll while you are slowing
down, which lets you steer properly.
*
[GF03600( ALL)01/96]
Do not drive with your foot resting on the brake
pedal. This will increase your vehicle's stopping
distance and may also cause brake damage.
*
[GF03650( ALL)01/96]
RWARNING
If you are driving down a long or steep
hill, shift to a lower gear. Do not apply
your brakes continuously, as they may
overheat and become less effective.
[GF03700( M)01/96]
When front or rear brake linings are replaced, it
is essential that authorized Ford service
replacement or equivalent linings be installed.
This will assure that the vehicle stopping
distances are not adversely affected and will
maintain the proper balance between front and
rear wheel braking.
%
*
[GF03750( ALL)01/96]
Using the Parking Brake
[GF03900( E M)01/96]
The parking brake pedal is suspended just below
the bottom of the instrument panel to the left of
the service brake. To set the parking brake while
parking your vehicle, press the brake pedal with
your right foot and hold it while you push the
parking brake pedal down firmly with your left
foot.
[GF03950( M)01/96]
The BRAKE warning light will go on as soon as
you start to move the parking brake pedal. The
brake will not prevent the vehicle from moving
unless you push it down firmly and fully.
Remove your foot from the service brake pedal
and make sure there is no vehicle movement.
File:09ltgfm.ex
Update:Fri Dec 13 11:22:54 1996
Page 59 of 224
55
*
[GF08325( ALL)01/96]
When to use 1 (Low)
*
[GF08350( ALL)01/96]
Use 1 (Low) to provide maximum engine
braking on steep downgrades. Upshifts from 1
(Low) can be made by manually shifting to 2
(Second) orj(Overdrive). Selection of 1 (Low)
gear provides only low gear operation from
start-up. Selection of 1 (Low) while at higher
speeds provides a shift to second gear, and a
shift to first gear will occur after the vehicle
decelerates to the proper speed.
*
[GF08375( ALL)01/96]
P (Park)
*
[GF08400( ALL)01/96]
Always come to a complete stop before you shift
into P (Park). This position locks the
transmission and prevents the rear wheels from
turning. To securely latch the gearshift in the P
(Park) position, pull it toward you, push it
completely counterclockwise against the stop,
and then push it toward the instrument panel.
*
[GF08425( ALL)01/96]
The gearshift is securely latched in P (Park) if
you cannot rotate it in a clockwise direction
without lifting it toward you.
*
[GF08450( ALL)01/96]
RWARNING
Always set the parking brake fully and
make sure the gearshift is latched in P
(Park). Turn off the ignition whenever you
leave your vehicle.
*
[GF08525( ALL)01/96]
RWARNING
Never leave your vehicle unattended
while it is running.
File:09ltgfm.ex
Update:Fri Dec 13 11:22:54 1996
Page 74 of 224
70 [GF22120( ALL)01/96]Trailer lamps
*
[GF22130( ALL)01/96]
Make sure your trailer lamps conform to Federal
and local regulations.
[GF22140( M)01/96]
NOTE: Do not connect a trailer lighting system
directly to the lighting system of the
vehicle. See your local recreational
vehicle dealer or rental trailer agency
for correct type of wiring and relays
for your trailer and heavy-duty
flashers. Incorrect installation may
result in either a false warning or no
warning in the lamp outage warning
system.
*
[GF22200( ALL)01/96]
RWARNING
Always replace a fuse with one that has
the specified amperage rating. Using a
fuse with a higher amperage rating can
cause severe wire damage and could start
a fire.
%*
[GF22210( ALL)01/96]
Driving While You Tow
*
[GF22220( ALL)01/96]
Be especially careful when driving while you
tow a trailer. Never drive faster than 45 mph
(70 km/h) when you tow in hilly country on
hot days. Also, anticipate stops so that you can
brake gradually.
%*
[GF22230( ALL)01/96]
If you use the speed control while you are
towing on very long, steep grades, the speed
control may shut off.
[GF22250( M)01/96]
If your vehicle is equipped with an Electronic
4-Speed Automatic (E4OD) transmission, operate
in Overdrive. Refer to the automatic
transmission operation earlier in this chapter.
[GF22260( M)01/96]
For normal driving conditions, operate in
Overdrive. Refer to the E4OD transmission
operation earlier in this chapter.
File:09ltgfm.ex
Update:Fri Dec 13 11:22:54 1996
Page 75 of 224
71
*
[GF22270( ALL)01/96]
When descending a steep grade with a trailer,
operate in Drive rather than Overdrive. If
additional braking is needed, shift the automatic
transmission gearshift into 2 (Second) gear or 1
(Low).
[GF22300( ALL)01/96]
Servicing your vehicle if you tow
*
[GF22310( ALL)01/96]
If you tow a trailer for a long distance, your
vehicle will need to be serviced more frequently
than usual. Refer to theMaintenance Schedule and
Recordbooklet for additional information.
[GF22320( ALL)01/96]
Trailer towing tips
*
[GF22330( ALL)01/96]
Before starting on a trip, practice turning,
stopping and backing in an area away from
heavy traffic. Get to know the ªfeelº of the
vehicle/trailer combination.
*
[GF22340( ALL)01/96]
Practice backing up. Back up very slowly, with
someone outside at the rear of your trailer to
guide you. Place your hand at the bottom of the
steering wheel and move it in the direction you
want the rear of the trailer to swing. Slight
movement of the steering wheel results in a
much larger movement of the rear of the trailer.
*
[GF22350( ALL)01/96]
Allow more room for stopping with a trailer
attached. Trailer brakes should be applied first,
whether manually or automatically controlled,
when approaching a stop.
*
[GF22360( ALL)01/96]
For a good handling truck-trailer combination,
the trailer tongue load should be approximately
10-15% of the loaded trailer weight.
*
[GF22370( ALL)01/96]
Make a thorough check of your equipment
before starting out on the road. After you have
traveled about 50 miles (80 km) stop in a
protected area and double-check your hitch and
electrical connections. Also check trailer wheel
lug nuts for tightness.
File:09ltgfm.ex
Update:Fri Dec 13 11:22:54 1996
Page 76 of 224
72
*
[GF22380( ALL)01/96]
When turning, drive slightly beyond the normal
turning point so the trailer wheels will clear
curbs or other obstructions.
[GF22390( E M)01/96]
When stopped in traffic for long periods of time
in hot weather, place the gearshift selector lever
in P (Park) to increase the engine idle speed.
This aids in engine cooling and air conditioner
efficiency. If the engine overheats, move the
Function Selector Lever to VENT to stop the
compressor and increase the engine speed for a
short time.
*
[GF22410( ALL)01/96]
Vehicles with trailers should not be parked on a
grade. However, if you must park on a grade,
place wheel chocks under the trailer's wheels as
follows:
*
[GF22420( ALL)01/96]
q
Apply the brake pedal and hold.
*
[GF22430( ALL)01/96]
q
Have another person place the wheel chocks
under the trailer wheels.
*
[GF22440( ALL)01/96]
q
With the chocks in place, release the brake
pedal, making sure the chocks are holding.
[GF22460( E M)01/96]
q
Apply the parking brake by pressing the
brake pedal down firmly with your right foot
while applying the parking brake pedal with
your left foot.
*
[GF22490( E M)01/96]
q
Shift the gearshift lever into P (Park).
*
[GF22500( ALL)01/96]
To start, after being parked on a grade:
*
[GF22510( ALL)01/96]
q
Apply the brake pedal and hold.
*
[GF22520( ALL)01/96]
q
Start the engine.
*
[GF22530( ALL)01/96]
q
Shift transmission into gear and release the
parking brake.
*
[GF22540( ALL)01/96]
q
Release the brake pedal and move the vehicle
uphill to free the wheel chocks.
*
[GF22550( ALL)01/96]
q
Apply the brake pedal and hold while
another person retrieves the chocks.
File:09ltgfm.ex
Update:Fri Dec 13 11:22:54 1996
Page 81 of 224
77
Roadside Emergencies
%*
[ER00205( ALL)01/96]
If the Engine Cranks but Does
Not Start or Does Not Start After
a Collision
*
[ER00210( ALL)01/96]
Fuel Pump Shut-Off Switch
*
[ER00220( ALL)01/96]
If the engine cranks but does not start or does
not start even after a small collision, the fuel
pump shut-off switch may have been activated.
The shut-off switch is a device intended to stop
the fuel pump when your vehicle has been
involved in a substantial jolt.
*
[ER00225( ALL)01/96]
Once the shut-off switch is activated, you must
reset the switch by hand before you can start
your vehicle.
[ER00235( M)01/96]
one third page art:0020006-B
Fuel pump shut-off switch location
File:10lterm.ex
Update:Fri Dec 13 11:23:45 1996
Page 116 of 224
112
*
[MC13800( ALL)01/96]
4. Let the engine coolant drain into a suitable
container. Disconnect the lower radiator hose
at the radiator connector and drain any
remaining engine coolant into a container.
*
[MC13850( ALL)01/96]
5. Reconnect the lower radiator hose and close
the radiator drain cock.
*
[MC13900( ALL)01/96]
Proper procedures for flushing the cooling
system can be found in theTruck Service Manual.
[MC13950( ALL)01/96]
Engine coolant refill procedure
*
[MC14000( ALL)01/96]
After you have drained the engine cooling
system:
*
[MC14050( ALL)01/96]
1. Fill the radiator with a 50/50 mixture of the
specified engine coolant concentrate and
water. Allow several minutes for trapped air
to escape (bubble out) and for engine coolant
to flow through the radiator.
*
[MC14100( ALL)01/96]
2. Replace the radiator cap to its fully installed
position, then back off to the first stop. This
will prevent high pressure from building up
in the cooling system during this part of the
fill procedure.
*
[MC14150( ALL)01/96]
3. Start and idle the engine until the thermostat
opens and the radiator upper hose becomes
warm.
*
[MC14200( ALL)01/96]
4. Shut off the engine and allow the engine to
cool. Cover the radiator cap with a thick
cloth and cautiously remove it. Step back
while the pressure releases.
*
[MC14250( ALL)01/96]
5. Finally, check the radiator and add more
engine coolant if needed, following the
procedures noted above. Reinstall the
radiator cap securely, when finished.
*
[MC14300( ALL)01/96]
6. If more engine coolant is necessary, fill the
overflow reservoir to the appropriate level
marked on the bottle.
File:11ltmcm.ex
Update:Fri Dec 13 11:24:54 1996