coolant temperature FORD F150 1997 10.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1997, Model line: F150, Model: FORD F150 1997 10.GPages: 219, PDF Size: 2.21 MB
Page 5 of 219
3
50
30704080
120
14040
20
90 60
8060100
20 km/h0000052
4
5
6 1LHEF3
50
30704080
120
14040
20
90 60
8060100
20 km/h0000052
4
5
6 1LHEF
PON
OFFRES
SET
ACCEL
COAST
INT 2
INT 1
OFF
OVERDRIVE OFF
PANEL
DIMAUTO
LAMP
CH818CH818
SRS
Charging
system
gauge
(pg. 16)Engine oil
pressure gauge
(pg. 16)Engine
coolant
temperature
gauge
(pg. 15)Fuel gauge
(pg. 15)
Speedometer
(pg. 14)Speed control*
(pg. 33)
Tachometer*
(pg. 15)Transmission
control switch
(pg. 38)
Driver air bag
(pg. 66) Turn signal and
wiper/washer control
(pg. 36)
Instrument panel
dimmer switch
(pg. 20) Headlamp
control
(pg. 18)
Instrumentation
6
Page 8 of 219
Engine coolant temperature
Illuminates briefly when the
ignition key is turned to On (light
from optional cluster shown).
Illuminates when the engine
coolant temperature is high. Stop
the engine and check the engine
coolant temperature level as soon
as possible. Refer toChecking
and adding engine coolantand
What you should know about
fail-safe coolingin the
Maintenance and caresection.
Oil pressure
Illuminates briefly when the
ignition key is turned to On (light
from base cluster shown).
Illuminates when the oil pressure
is low. Stop the engine and check
the engine oil level as soon as
possible. Refer toChecking and
adding engine oilin the
Maintenance and caresection.
Door ajar
Illuminates when the ignition
switch is in the ON or START
position and any door is open.
Charging system
Briefly illuminates when the
ignition is turned on and the
engine is off. The light also
illuminates when the battery is not
charging properly, requiring
electrical system service.
DOOR
AJAR
f12_oil_pressure
com_door-ajar.02
com_charging_system.01
com_brake_system.01
Instrumentation
9
Page 14 of 219
Tachometer (if equipped)
Indicates the engine speed in
revolutions per minute.
Engine coolant temperature
gauge
Indicates the temperature of the
engine coolant. At normal
operating temperature, the needle
remains within the normal area. If
it enters the red section, the
engine is overheating. Switch off
the ignition and let it cool. Refer to
Checking and adding engine
coolantorWhat you should know
about fail safe coolingin the
Maintenance and carechapter.
Fuel gauge
Indicates the fuel level.
0RPMx1000
3
2
4
5
6 1
CHCH
EF
f12_engine_coolant
f12_fuel_gauge f12_voltage_gauge
Instrumentation
15
Page 87 of 219
STARTING PROCEDURE
Starting the engine
1. Turn the key to 5 (Start)
without pressing the accelerator.
The key will return to 4 (On).
2. If the engine does not start
within five seconds, wait ten
seconds and try again.
3. If the engine does not start in
two attempts OR the temperature
is below Ð12ÉC (10ÉF), depress
accelerator and start the engine
while holding the accelerator
down. Release accelerator when
engine starts.
4. After idling for a few seconds,
apply the brake and release the
parking brake.
Using the engine block heater
(if equipped)
An engine block heater warms the
engine coolant, which improves
starting, warms up the engine
faster and allows the
heater-defroster system to respond
quickly. They are strongly
recommended if you live in a
region where temperatures reach
Ð23ÉC (±10ÉF) or below.
For best results, plug the heater in
at least three hours before starting
3
2
1
5
4
com_starting_vehicle.01
com_engine_heater.01
Starting
88
Page 165 of 219
CHECKING AND ADDING
WINDSHIELD WASHER FLUID
1. Lift the washer fluid reservoir
cover.
2. Add washer fluid intil the level
reaches the FULL line.
Use only fluid that meets Ford
Specifications. Refer toCapacities
and specifications.
The addition of a bug shield to the
front of the vehicle may adversely
affect the washer system from
delivering fluid to the windshield.
Devices such as bug shields are
not recommended.
Windshield washer fluid
contains methanol and it is
poisonous. Follow all instructions
on the bottle of washer fluid.
What you should know about
washer fluid
In freezing weather [temperatures
below 0ÉC (32ÉF)], use washer
fluid containing a small amount of
antifreeze, such as methanol. State
or local regulations on volatile
organic compounds (VOCs) may
restrict the use of methanol, a
common type of antifreeze.
Use a non-methanol antifreeze in
freezing weather only if the fluid
does not damage the paint finish,
wiper blades and washer system.
WASHER FLUID
ONLY
f12_wysk_washer_fluid
f12_coolant
Maintenance and care
166
Page 169 of 219
freeze at the temperature level in
which you drive during winter
months. Never increase the engine
coolant concentration above 60%.
Leave a 50/50 mixture of engine
coolant and water in your vehicle
year-round in non-extreme
climates.
Checking the cooling system
hoses
Inspect all engine and heater
system hoses and hose connections
for:
²deterioration
²leaks
²loose hose clamps
What you should know about
fail-safe cooling (if equipped)
Vehicles equipped with 4.6L or
5.4L engines have a fail-safe
com_checking_hoses.01
f12_wysk_failsafe_cooling
Maintenance and care
170
Page 170 of 219
cooling mode. If the engine coolant
supply is depleted, this feature
allows the driver to drive the
vehicle (with limited power) for a
short distance in order to get the
vehicle to a service facility. Take
your vehicle to a service facility as
soon as possible to minimize
engine damage.
The actual distance your vehicle
can be driven depends on vehicle
load, road conditions and outside
temperature.
How fail-safe cooling works
If the engine overheats, the engine
will automatically switch from
eight to alternating four cylinder
operation. Each disabled cylinder
acts as an air pump and cools the
engine.
When this occurs, the engine
coolant temperature gauge will
move into the red area and the
light illuminates.
The
CHECK
ENGINElight will illuminate,
indicating that vehicle service is
required.
The vehicle will still operate, but
will have limited engine power and
no air conditioning capability.
Continued operation will increase
engine temperature and cause the
engine to completely shut down.
The vehicle will coast to a stop.
As the engine temperature cools,
the engine may be re-started. Take
your vehicle to a service facility as
CHCH
Maintenance and care
171
Page 172 of 219
2. When the engine coolant
temperature gauge reaches the
normal zone, turn the engine off.
3. Visually inspect the fluid level in
the power steering fluid reservoir.
4. Add power steering fluid until
the fluid level reaches MAX.
Use only fluid that meets Ford
specifications. Refer toCapacities
and specifications.
CHECKING AND ADDING
TRANSMISSION FLUID
Checking and adding automatic
transmission fluid (if equipped)
Service the automatic transmission
according to the scheduled
intervals in the ªService Guide.º
MAX
MIN
MAX
MIN
f12_trans_fluid
f12_checking_adding_autotrans
Maintenance and care
173