ignition FORD F250 1997 Owner's Manual

92
*
[CF67400(F )01/96]
quarter page art:0020790-A
Replacing the batteries
%*
[CF67500(F )01/96]
Replacing lost transmitters
*
[CF67600(F )01/96]
In the event a transmitter is lost, you should
take all your vehicle's transmitters to your
dealer to have the remote entry system
deprogrammed for the lost transmitter. This is
necessary to prevent further unauthorized use of
the lost transmitter.
*
[CF67700(F )01/96]
You can also purchase additional transmitters
(up to 4 transmitters can be used) from your
dealer. You will need to take all your
transmitters to the dealer so they can program
them to the remote entry system all at the same
time.
%*
[CF68000(F )01/96]
Illuminated Entry System (If equipped)
[CF68100(F )01/96]
This system will provide illumination of the
vehicle's interior courtesy lamps when either
outside front door handle is pulled or when the
Remote Entry System is used to unlock the door
or sound the Personal Alarm. The system will
automatically turn off after approximately 25
seconds or when the ignition is turned to the
START or ACCESSORY position.
[CF68200(F )04/96]
NOTE: The inside lights will not turn off if
you have turned them on with the
dimmer knob or if any door is open.
File:05ltcff.ex
Update:Tue May 28 08:42:43 1996
ProCarManuals.com

93 % [CF68300(F )04/96]
Battery Saver (with Remote Entry Ð If
equipped)
[CF68400(F )04/96]
When the ignition is turned off, the vehicle will
turn off battery voltage to all of these lights after
45 minutes: glove box, engine compartment,
overhead console, mirror, courtesy and
interior (including cargo) lamps.
*
[CF68500(F )01/96]
This will prevent draining of the battery if these
lights have been left on inadvertently or if a
door is not completely closed. Battery voltage to
these lamps will be restored when the remote
entry transmitter is used, any door is opened, or
the ignition key is turned on again.
File:05ltcff.ex
Update:Tue May 28 08:42:43 1996
ProCarManuals.com

139 %
*
[TO02300(FM)01/96]
Starting Your Engine
*
[TO02400(FM)01/96]
To start your engine:
*
[TO02500(FM)01/96]
1. Follow the steps underPreparing to Start
Your Vehicleat the beginning of this section.
*
[TO02600(FM)01/96]
2. Turn the ignition key to the ON position.
*
[TO02700(FM)01/96]
3. DO NOT depress the accelerator pedal when
starting your engine. DO NOT use the
accelerator while the vehicle is parked.
*
[TO02800(FM)01/96]
4. Turn the key to the START position
(cranking) until the engine starts. Allow the
key to return to the ON position after the
engine has started.
*
[TO02900(FM)01/96]
If you have difficulty in turning the key,
rotate the steering wheel slightly because it
may be binding.
%*
[TO03000(FM)01/96]
For a cold engine:
*
[TO03100(FM)01/96]
q
At temperatures10ÊF (-12ÊC) andbelow:If
the engine does not start infifteen (15)
secondson the first try, turn the key to OFF,
wait approximately ten (10) seconds so you
do not flood the engine, then try again.
*
[TO03200(FM)01/96]
q
At temperaturesabove10ÊF(-12ÊC):If the
engine does not start infive (5) secondson
the first try, turn the key to OFF, wait
approximately ten (10) seconds so you do not
flood the engine, then try again.
*
[TO03300(FM)01/96]
q
Do not hold the key in the START position
for more thanfifteen (15) secondsat a time.
File:08lttof.ex
Update:Tue May 28 08:44:45 1996
ProCarManuals.com

140 %
*
[TO03400(FM)01/96]
For a warm engine:
*
[TO03500(FM)01/96]
q
Do not hold the key in the START position
for more thanfive (5) secondsat a time. If
the engine does not start within five (5)
seconds on the first try, turn the key to the
OFF position. Wait a few seconds after the
starter stops, then try again.
*
[TO03600(FM)01/96]
Whenever you start your vehicle, release the key
as soon as the engine starts. Excessive cranking
could damage the starter.
*
[TO03700(FM)01/96]
After you start the engine, let it idle for a few
seconds. Keep your foot on the brake pedal and
put the gearshift lever in gear. Release the
parking brake. Slowly release the brake pedal
and drive away in the normal manner.
%*
[TO03800(FM)05/96]
NOTE: Your vehicle is equipped with a
brake-shift interlock feature. This
feature prevents you from shifting
from P (Park) unless you have the
brake pedal depressed. (The ignition
must be in the ON position.) If you
cannot shift from P (Park) with the
brake pedal depressed:
*
[TO03900(FM)05/96]
1. Apply the parking brake.
*
[TO04000(FM)05/96]
2. Remove the key.
*
[TO04100(F )05/96]
3. Insert the key and rotate it one position
clockwise (ignition in the OFF position).
*
[TO04200(FM)05/96]
4. Apply the brake pedal and shift to N
(Neutral). (If the vehicle is shifted back to P
[Park], you must repeat the previous steps.)
*
[TO04300(FM)05/96]
5. Start the vehicle.
File:08lttof.ex
Update:Tue May 28 08:44:45 1996
ProCarManuals.com

141
*
[TO04400(FM)05/96]
If you need to shift out of P (Park) by using the
alternate procedure described above, it is
possible that a fuse has blown and that your
brakelamps may also not be functional. Please
refer to the chapter titledRoadside Emergenciesin
this Owner Guide for instructions on checking
and replacing fuses.
*
[TO04500(FM)05/96]
RWARNING
DO NOT DRIVE YOUR VEHICLE UNTIL
YOU VERIFY THAT THE BRAKELAMPS
ARE WORKING.
[TO04600(FM)04/96]
For cold or warm engines:
*
[TO04700(FM)01/96]
If the engine still does not start after two
attempts:
*
[TO04800(FM)01/96]
1. Turn the ignition key to the OFF position.
*
[TO04900(FM)01/96]
2. Press the accelerator all the way to the floor
and hold it.
*
[TO05000(FM)01/96]
3. Turn the ignition key to the START position.
*
[TO05100(FM)01/96]
4. Release the ignition key when the engine
starts.
*
[TO05200(FM)03/96]
5. Release the accelerator gradually as the
engine speeds up.
*
[TO05300(FM)05/96]
If the engine still does not start, the fuel pump
shut-off switch may have been activated. For
directions on how to reset the switch seeFuel
Pump Shut-Off Switchin the index.
*
[TO05500(F )01/96]
A computer system controls the engine's idle
speed. When you start your vehicle, the engine's
idle speed normally runs higher than when it's
warmed up. These faster engine speeds will
make your vehicle move slightly faster than its
File:08lttof.ex
Update:Tue May 28 08:44:45 1996
ProCarManuals.com

150 [GF04300(F )05/96]When the transfer case is in the N (Neutral)
position, the engine and transmission are
disconnected from the rest of the driveline.
Therefore, the vehicle is free to roll even if the
automatic transmission is in P (Park) or the
manual transmission is in gear.
*
[GF04350(F )05/96]
RWARNING
Do not leave the vehicle unattended with
the transfer case in the N (Neutral)
position. Always set the parking brake
fully and turn off the ignition when
leaving the vehicle.
[GF04400(FM)04/96]
To release the parking brake, press the service
brake pedal with your right foot and pull the
parking brake release lever.
*
[GF04500(FM)02/96]
RWARNING
If the parking brake is fully released, but
the Brake System light remains on, have
the brakes checked immediately. They
may not be working properly.
*
[GF04550(F )03/96]
The parking brake is not designed to stop a
moving vehicle, but you can use the parking
brake to stop your vehicle in an emergency if
the normal brakes fail. However, since the
parking brake applies only the rear brakes, the
stopping distance will increase greatly and the
handling of your vehicle will be adversely
affected.
File:09ltgff.ex
Update:Thu May 30 15:25:49 1996
ProCarManuals.com

154 %
*
[GF07800(FM)05/96]
NOTE: Your vehicle is equipped with a
brake-shift interlock feature. This
feature prevents you from shifting
from P (Park) unless you have the
brake pedal depressed. (The ignition
must be in the ON position.) If you
cannot shift from P (Park) with the
brake pedal depressed:
*
[GF07825(FM)05/96]
1. Apply the parking brake.
*
[GF07850(FM)05/96]
2. Remove the key.
*
[GF07875(FM)05/96]
3. Insert the key and rotate it one position
clockwise (ignition in the OFF position).
*
[GF07900(FM)05/96]
4. Apply the brake pedal and shift to N
(Neutral). (If the vehicle is shifted back to P
[Park], you must repeat the previous steps.)
*
[GF07925(FM)05/96]
5. Start the vehicle.
*
[GF07950(FM)05/96]
If you need to shift out of P (Park) by using the
alternate procedure described above, it is
possible that a fuse has blown and that your
brakelamps may also not be functional. Please
refer to the chapter titledRoadside Emergenciesin
this Owner Guide for instructions on checking
and replacing fuses.
*
[GF07975(FM)05/96]
RWARNING
DO NOT DRIVE YOUR VEHICLE UNTIL
YOU VERIFY THAT THE BRAKELAMPS
ARE WORKING.
%*
[GF08000(FM)05/96]
R (Reverse)
*
[GF08025(FM)05/96]
With the gearshift in the R (Reverse) position,
the vehicle will move backward. You should
always come to a complete stop before shifting
into or out of R (Reverse).
File:09ltgff.ex
Update:Thu May 30 15:25:49 1996
ProCarManuals.com

157
*
[GF08375(FM)05/96]
P (Park)
*
[GF08400(FM)05/96]
Always come to a complete stop before you shift
into P (Park). This position locks the
transmission and prevents the rear wheels from
turning. To securely latch the gearshift in the P
(Park) position, pull it toward you, push it
completely counterclockwise against the stop,
and then push it toward the instrument panel.
*
[GF08425(FM)05/96]
The gearshift is securely latched in P (Park) if
you cannot rotate it in a clockwise direction
without lifting it toward you.
*
[GF08450(FM)05/96]
RWARNING
Always set the parking brake fully and
make sure the gearshift is latched in P
(Park). Turn off the ignition whenever you
leave your vehicle.
[GF08475(F )05/96]
When the transfer case is in the N (Neutral)
position, the engine and transmission are
disconnected from the rest of the driveline.
Therefore, the vehicle is free to roll even if the
automatic transmission is in P (Park) or the
manual transmission is in gear.
*
[GF08500(F )05/96]
RWARNING
Do not leave the vehicle unattended with
the transfer case in the N (Neutral)
position. Always set the parking brake
fully and turn off the ignition when
leaving the vehicle.
*
[GF08525(FM)05/96]
RWARNING
Never leave your vehicle unattended
while it is running.
File:09ltgff.ex
Update:Thu May 30 15:25:49 1996
ProCarManuals.com

162
*
[GF14850(F )01/96]
When you come to a stop, do not downshift
through each gear. Disengage the clutch and use
the brake as necessary. Downshifting through
the gears decreases your vehicle's fuel economy.
*
[GF14900(F )01/96]
RWARNING
Continued use of a damaged or worn
clutch, prolonged clutch slippage or
downshifting at excessive speeds can
result in a failure of the engine,
transmission or clutch components.
*
[GF14950(F )01/96]
Transmission Function
[GF15000(F )04/96]
Upshift at the speeds specified in the chart
available for your engine and transmission. All
forward gears are synchronized allowing you to
shift into them with your vehicle in motion. The
clutch pedal should be fully depressed when
shifting.
*
[GF15050(F )03/96]
NOTE: Shifting during extremely low RPMs
can result in a momentary audible
rattle which disappears as vehicle
RPMs are increased. Shifting at higher
speeds will eliminate this sound.
*
[GF15100(F )01/96]
Parking
*
[GF15150(F )01/96]
To park your vehicle, apply the service brake
pedal, and shift into N (Neutral) while still
maintaining pressure on the service brake. Set
the parking brake fully. Shift into first and turn
off the ignition.
*
[GF15200(F )01/96]
RWARNING
Do not park your vehicle in Neutral, it
may move unexpectedly and injure
someone. Use 1 (First) gear and set the
parking brake fully.
File:09ltgff.ex
Update:Thu May 30 15:25:49 1996
ProCarManuals.com

163 [GF15250(F )05/96]
When the transfer case is in the N (Neutral)
position, the engine and transmission are
disconnected from the rest of the driveline.
Therefore, the vehicle is free to roll even if the
automatic transmission is in P (Park) or the
manual transmission is in gear.
*
[GF15300(F )05/96]
RWARNING
Do not leave the vehicle unattended with
the transfer case in the N (Neutral)
position. Always set the parking brake
fully and turn off the ignition when
leaving the vehicle.
%
*
[GF15400(F )01/96]
Four-Wheel Drive (4WD)
System (If equipped)
*
[GF15500(F )01/96]
When you select the 4WD mode, your light
truck uses all four wheels to power itself. This
increases traction, enabling you to drive your
4x4 over terrain and road conditions two-wheel
drive vehicles cannot.
*
[GF15600(F )01/96]
Power is supplied to all four wheels through a
transfer case that allows you to select four-wheel
drive when necessary. Methods for engaging and
disengaging 4WD and low range will depend on
which system your vehicle has.
File:09ltgff.ex
Update:Thu May 30 15:25:49 1996
ProCarManuals.com