fuel pump FORD F750 2003 10.G Owners Manual

These are some of the symbols you may see on your vehicle.
Safety Alert
See Owner’s Guide
Fasten Safety BeltAir Bag-Front
Air Bag-SideChild Seat
Child Seat Installation
WarningChild Seat Tether
Anchorage
Brake SystemAnti-Lock Brake System
Brake Fluid -
Non-Petroleum BasedTraction Control
AdvanceTracMaster Lighting Switch
Hazard Warning FlasherFog Lamps-Front
Fuse CompartmentFuel Pump Reset
Windshield Wash/WipeWindshield
Defrost/Demist
Rear Window
Defrost/DemistPower Windows
Front/Rear
Power Window LockoutChild Safety Door
Lock/Unlock
Introduction
6

Water in fuel (if equipped)
During refueling it is possible for
water-contaminated diesel fuel to be
pumped into your fuel tank. Your
vehicle fuel system is equipped with
a fuel filter/water separator to
remove water from the fuel. The indicator light illuminates when the fuel
filter/water separator has a significant quantity of water, or when the
ignition key is switched to the START position. If the light illuminates
when the engine is running, stop the vehicle as soon as safely possible,
shut off the engine and drain the filter bowl. Allowing water to stay in
the system could result in extensive damage to, or failure of, the fuel
injection system.
To drain the fuel filter/water separator (refer toMaintenance and
Specificationschapter for procedure). Rotate the valve at the bottom of
the filter assembly allowing water to drain from the system. Close the
valve upon completion.
Do not drain water separator while engine is running. Fuel may
ignite if separator is drained while engine is running or vehicle is
moving.
Air clean warning (if equipped)
Illuminates when the air system is
restricted (dirty, clogged).
Turn signal
Illuminates when the left or right
turn signal or the hazard lights are
turned on. If one or both of the
indicators stay on continuously or flash faster, check for a burned-out
turn signal bulb. Refer toExterior bulbsin theLightschapter.
High beams
Illuminates when the high beam
headlamps are turned on.
WATER
IN
FUEL
AIR
CLEAN
Instrumentation
14

•Set fan speed on high with function control to any position except
OFF or MAX A/C and the temperature control on any desired position.
•Adjust air control system to force outside air into the vehicle.
Winter fronts
If using an aftermarket winter front (not recommended), it must have a
permanent opening directly in line with the center of the fan drive. The
minimum opening size must be at least 774 square cm (120 square
inches).
The use of an aftermarket winter front or other air flow restriction
device mounted in front of the radiator is not recommended on this
vehicle. Air flow restriction will cause high exhaust temperatures, power
loss, excessive fan usage and a reduction in fuel economy.
HYDRAULIC BRAKES (IF EQUIPPED)
Your service brakes are self-adjusting. Refer to theGeneral
Maintenance Informationfor scheduled maintenance.
Occasional brake noise is normal and often does not indicate a
performance concern with the vehicle’s brake system. In normal
operation, automotive brake systems may emit occasional or intermittent
squeal or groan noises when the brakes are applied. Such noises are
usually heard during the first few brake applications in the morning;
however, they may be heard at any time while braking and can be
aggravated by environmental conditions such as cold, heat, moisture,
road dust, salt or mud. If a“metal-to-metal,”“continuous grinding”or
“continuous squeal”sound is present while braking, the brake linings
may be worn-out and should be inspected by a qualified service
technician.
If you are driving down a long or steep hill, shift to a lower gear.
Do not apply your brakes continuously, as they may overheat
and become less effective.
HYDRAULIC BRAKE BOOSTER SYSTEM (HYDROMAX)
The Hydromax systems receive fluid pressure from the power steering
pump to provide power assist during braking.
The Hydromax booster receives backup pressure from the reserve
system electric pump whenever the fluid in the power steering system is
not flowing. When the engine is OFF, the pump will turn on if the brake
pedal is applied, or if the ignition is turned to the ON position.
Driving
113

Fuse/Relay
LocationFuse Amp
RatingPassenger Compartment Fuse
Panel Description
15 10A GEM, Interior lamp relay, Map
lamps, Glove box lamps
(SuperCrewzer only), Power
mirrors (SuperCrewzer only),
Warning chime module
(SuperCrewzer only)
16 15A Highbeams
17—Not used
18 5A Headlamp switch, GEM
19 15A Engine, Cluster, Cummins PCM,
CAT PCM, 7.3L Power Stroke
PCM (idle valid switch input),
Alternator (Ambulance only)
20 15A Starter relay, GEM
21 10A DRL
22 15A Exhaust brake (SuperCrewzer
only), Heated mirrors
(SuperCrewzer only), Rear air
suspension (SuperCrewzer and
Ambulance)
23 10A Electronic flasher
24 15A Vacuum pump, Air dryer, ABS,
Fuel heater relay
25 10A Blower motor relay
26 10A Right-hand low beam headlamp
27—Not used
28 10A Left-hand low beam headlamp
Roadside Emergencies
154

The high-current fuses and relays are coded as follows.
Fuse/Relay
LocationFuse Amp
RatingPower Distribution Box
Description
1 15A* Park lamps, Roof lamps
2 25A* Cummins Powertrain Control
Module (PCM)
15A* Foglamps (SuperCrewzer only)
3 10A* Generator
4 15A* Washer pump
5 15A* CAT air intake heater relay,
Cummins PCM
6 20A* CAT PCM, Cummins PCM
7 15A* Stop lamps
8 25A* CAT fuel heater
9 30A* Trailer hook-up lamps
(SuperCrewzer only)
10 15A* Shift modulator (Allison AT
transmission only) (except for
F–650 SuperCrewzer and
Caterpillar/Cummins)
503
304
303
302301
502
501
207201
202
203
204122118114110106102
121117113109105101
120116112108104
119115111107103
24
209206
208
18161412108642
1715131197531
205
23
22
21
401
20
19
Roadside Emergencies
156

Maintenance Operation Frequency - Observation
Check the transmission and
engine mountings (*b)Hard shifting or excessive vibration
Check and adjust transmission
controls (*b)High effort to shift or noisy
transmission
Check fuel pump pressure Insufficient full-throttle power or
backfiring
Clean radiator cap seal. Clean
and inspect the cap surface on
the radiatorWhen the cap does not hold pressure
Check the battery terminals for
corrosionWhenever electrical power supply has
diminished
Tighten the wheel mounting
nuts to the specified torque.
Refer toServicing your
wheels and tiresRequired initially at 804 and 1 609 km
(500 and 1 000 miles). Perform again
at 804 and 1 609 km (500 and 1 000
mile) intervals after each tire
removal/replacement.
*a During maintenance and repair, protect the fuel tube and the hose
assemblies, the power steering lines, and the brake lines from the
external heat, the acids and the abrasion that could damage the lines.
*b Check for (free) linkage action and ensure that (return) spring
force is adequate to maintain pedal free play.
*c Adjust, repair or replace as required with the same or equivalent
parts.
General Maintenance Information
238