engine FORD F750 2004 11.G Owners Manual

Component /
Component vendorLubrication type Vendor
recommendations:
Viscosity / Ambient
temperature / NotesEquivalent Ford
part name / number
Spicer
(non-synchronized)
(lubricants are listed
in order of
preference)Petroleum oil:
Engine oil API-SL or
API-CF
(MIL-L-2104E or
MIL-L-46152E)SAE 50:–18°C
(above 0°F)—
SAE 40:–18°C
(below 0°F)—
Mineral gear oil:
API-GL-1 (rust and
oxidation inhibited)
(EP gear oils are not
acceptable)SAE 90:–18°C
(above 0°F)—
SAE 80:–18°C
(below 0°F)—
Synthetic oil:
Synthetic Engine Oil
meeting
MIL-L-2104E or
MIL-L-46152E,
API-SL or API-CFCD SAE 50: All
temperatures—
Spicer
(synchronized)
(lubricants are listed
in order of
preference)Petroleum oil:
Engine oil API-SL or
API-CF
(MIL-L-2104E or
MIL-L-46152E)SAE 50:–12°C
(above 10°F)—
SAE 40:–12°C
(below 10°F)—
Mineral gear oil:
API-GL-1 (rust and
oxidation inhibited)SAE 90:–12°C
(above 10°F)—
SAE 80W:–12°C
(below 10°F)—
Spicer
(synchronized)
(cont’d)Synthetic oil:
Synthetic Engine Oil
meeting
MIL-L-2104E or
MIL-L-46152E,
API-SL or API-CFSAE 50: All
temperatures—
2004 F650/750(f67)
Supplement
USA English(fus)
Maintenance and specifications
211

Component /
Component vendorLubrication type Vendor
recommendations:
Viscosity / Ambient
temperature / NotesEquivalent Ford
part name / number
Meritor Petroleum oil: Heavy
Duty Engine Oil
MIL-L-2104E or
API-SL or API-CF
(previous API
designations
acceptable)SAE 50:–12°C
(above 10°F)—
SAE 40:–12°C
(above 10°F)—
SAE 30:–12°C
(below 10°F)Motorcraft SAE 30
Super Duty Motor
Oil / XO-30-QSD
Mineral gear oil with
rust and oxidation
inhibitor API-GL-1*
(* Do not use
multi-weight and
GL-5 EP gear oils;
they may cause
transmission failure
or damage.)SAE 90:–12°C
(above 10°F)—
SAE 80:–12°C
(below 10°F)—
Synthetic oil:
MIL-L-2104E or
MIL-L-46152D (* Do
not use multi-weight
and GL-5 EP gear
oils; they may cause
transmission failure
or damage.)—SAE 50: All
temperatures—
Allison Refer to
transmission manual——
Rear axle
Eaton-Spicer -
two-speed axlesRHEOLUBE 362 (or
equivalent) (Eaton
part number
113741)——
2004 F650/750(f67)
Supplement
USA English(fus)
Maintenance and specifications
212

Component /
Component vendorLubrication type Vendor
recommendations:
Viscosity / Ambient
temperature / NotesEquivalent Ford
part name / number
Cab latch pivots;
Door check, hinges,
latches and strikers;
Seat adjuster slidesGC/LB NLGI #2
lithium
complex-based moly
grease (or
equivalent) or
multi-purpose
lithium complex
grease—Motorcraft Premium
Long Life Grease /
XG-1-C
Cab latch pivot pins Light engine oil—Motorcraft SAE
5W-30 Super
Premium Motor Oil /
XO-5W30-QSP
Door lock cylinders Lock oil—Motorcraft
Penetrating and
Lock Lubricant /
XL-1
Door window
regulatorsNGLI #2
multipurpose lithium
complez grease—Motorcraft
Multi-Purpose
Grease Spray / XL-5
or Motorcraft
Multi-Purpose
Grease / XG-4
Weatherstripping Silicone lubricant—Motorcraft Silicone
Spray / XL-6
Engine oil
6.0L Power Stroke
engineAPI CI-4 / SL SAE 15W–40 above
–12°C (10°F)Motorcraft SAE
15W-40 Super Duty
Motor Oil /
XO-15W40-QSD
SAE 10W-30–23°C
to 32°C(–10°Fto
90°F)Motorcraft SAE
10W-30 Super Duty
Motor Oil /
XO-10W30-QSD
SAE 0W–30 below
–18°C(0°F)Motorcraft SAE
0W-30 Super All
Season Motor Oil /
XO-0W30-LAS
Cummins B and
Caterpillar enginesRefer to engine operator manual
Brake fluid
All vehicles DOT 3,
ESA-M6C25–A—Motorcraft High
Performance Motor
Vehicle Brake Fluid /
PM-1
2004 F650/750(f67)
Supplement
USA English(fus)
Maintenance and specifications
216

Engine coolant and oil
Engine type Engine coolant
(approximate
capacity)Engine oil
(approximate
capacity)
6.0L Power Stroke 25.7L (54.4 pints) 18.0L (19 quarts)
Caterpillar 28.4 (60.0)
1
Cummins B 23.1 (24.4)1
1Refer to the engine operator manual for engine oil refill capacities.
Power steering system
Steering gearPower steering fluid volume (cubic
inches/liters/pints)
V8 engine
TAS40 steering gear 506/8.3/17.6
TAS65 steering gear 533/8.7/18.4
Transmission
Description Liters Pints
MD-3060P 5–speed automatic 27.4 58.01
MD-3560P 5–speed automatic 27.4 58.01
MD-3060P 6–speed automatic 27.4 58.01
FS-4205A 5–speed manual 5.4 11.5
MD-3066P 6–speed automatic 27.4 58.01
FS-5406A 6–speed manual 9.2 19.5
FS-5406N 6–speed manual 9.2 19.5
MD-3560P 6–speed automatic 27.4 58.0
1
2000P Series 5–speed automatic 18.0 38.01
2400 Series 5–speed automatic 18.0 38.01
FS-5205A 5–speed manual 5.9 12.5
FS-6406N 6–speed manual 9.2 19.5
FS-6406A 6–speed manual 9.2 19.5
ES066–7B 7–speed manual 9.9 20.9
ES56–7B 7–speed manual 9.9 20.9
FR-9210B 10–speed manual 11.1 23.5
RT–8908LL 10–speed manual 13.2 28.0
1Total fluid capacity (dry transmission and torque converter).
2004 F650/750(f67)
Supplement
USA English(fus)
Maintenance and specifications
218

GENERAL MAINTENANCE INFORMATION
The Scheduled Maintenance Services listed in this section are required
because they are considered essential to the life and performance of
your vehicle.
Ford Motor Company recommends you perform the Owner Maintenance
Services listed in this section. These services are matters of day-to-day
care that are important to the proper operation of your vehicle. In
addition to the conditions described in the Owner Maintenance Checklist,
be alert for any unusual noise, vibration or other indication that your
vehicle may need service and attend to it promptly.
Use only recommended fuels, lubricants, fluids and service parts
conforming to Ford specifications. Motorcraft parts are designed and
built for best performance in your vehicle. Using these parts for
replacement is your assurance that Ford-Built quality stays in your
vehicle.
SCHEDULED MAINTENANCE
The maintenance or replacement of the emission control devices (or
systems) in your new Ford Motor Company vehicle (or engine) may be
performed at your expense. These services may be performed by any
automotive repair establishment or individual using automotive parts
equivalent to those with which your vehicle or engine was originally
equipped. If any parts other than Ford, Motorcraft, or Ford authorized,
remanufactured parts are used for maintenance replacements (or for the
service) of components effecting the emission control, the owner should
be assured that such parts are warranted by their manufacturer to be
equivalent to genuine Ford Motor Company Parts in performance and
durability. Please consult your warranty information booklet for complete
warranty information.
Authorized dealer maintenance
Your authorized dealer specializes in knowing all about Ford Motor
Company vehicles rather than knowing a little about all makes.
There are Ford or Ford of Canada dealer service shops ready to serve
you wherever you drive in the U.S. or Canada. They stock Ford and
Motorcraft parts, and Ford Chemicals and lubricants. You can be
confident that these meet the same exacting design and quality
standards as those used to build the vehicle originally. Dealer Service
Technicians have available training in the latest product developments
and service techniques.
2004 F650/750(f67)
Supplement
USA English(fus)
General maintenance information
General maintenance information
222

OWNER MAINTENANCE
You can do much of the maintenance your vehicle requires yourself, if
you have the time and a reasonable amount of mechanical ability. If you
prefer to have this work done professionally, your authorized dealer
stands ready to help you.
All mechanical components and attachments are important in that they
could affect the performance of vital components and systems. If
replacement becomes necessary, they must be replaced with parts having
the same part number or with equivalent parts. Torque values of the
attaching parts must be used as specified during any reassembly
procedure to assure proper retention.
EMISSIONS CONTROL SYSTEM
To assure the emissions control systems operate effectively, you should
have the services listed in the maintenance schedule performed at the
specified time and km/mileage intervals. You should avoid running out of
fuel or turning off the ignition while the vehicle is in motion, especially
at high speeds.
Because of high engine compartment and exhaust system
temperatures resulting from emissions equipment, do not park,
idle or operate your vehicle in dry grass or other dry ground cover
where the possibility of ground fire exists.
Do not make unauthorized modifications to the engine or vehicle.
Modifications causing increased amounts of unburned fuel to reach the
exhaust system can significantly increase the temperature of the engine
compartment and/or the exhaust system.
Avoid driving your vehicle if it does not operate properly. If the engine
diesels (more than five seconds of engine run-on after shut-off), misfires,
surges, stalls or backfires, see your dealer. Be alert for fluid leakage,
odor, smoke, loss of oil pressure, or charge indicator or over temperature
warning.
Do NOT use diesel fuel blended with waste oil in engines equipped with
a catalytic converter-muffler. Waste lube oil blending in fuel will plug the
catalytic converter-muffler, resulting in a significant loss of engine power.
2004 F650/750(f67)
Supplement
USA English(fus)
General maintenance information
223

Emissions control system(s) laws
Federal law prohibits vehicle manufacturers, dealers and other persons
engaged in the business of repairing, servicing, selling, leasing or trading
motor vehicles, as well as fleet operators from knowingly removing or
rendering an emissions control device or system inoperative. Further,
modifications of the emissions control system(s) could create liability on
the part of individual owners under the laws of some states. In Canada,
modification of the emissions control system could create liability under
applicable Federal or Provincial laws.
NOISE EMISSIONS WARRANTY, PROHIBITED TAMPERING ACTS
AND MAINTENANCE
On January 1, 1978, Federal regulations became effective governing the
noise emissions on trucks over 4,536 kg. (10,000 lbs.) GVWR. The
following statements concerning prohibited tampering acts and
maintenance and the noise warranty are found in the Warranty Guide,
and are applicable to completed trucks.
Tampering with noise control system prohibited
Federal law prohibits the following acts or the causing thereof: (1) The
removal or rendering inoperative, by any person other than for purposes
of maintenance, repair or replacement, of any device or element of
design incorporated into any new vehicle for the purpose of noise control
prior to its sale or delivery to the ultimate purchaser or while it is in use,
or (2) the use of the vehicle after such device or element of design has
been removed or rendered inoperative by any person.
Among those acts presumed to constitute tampering are the following
acts listed:
Vehicle System Acts
Acoustical Shielding Removal of noise shields, hood
blanket, tunnel liner or acoustical
absorptive material.
Engine Removal or rendering inoperative
the engine speed governor so as to
allow engine speed to exceed
manufacturer specifications.
Removal of engine mounted noise
shield or oil pan enclosure.
2004 F650/750(f67)
Supplement
USA English(fus)
General maintenance information
224

Vehicle System Acts
Engine Air Induction System Removal of the air duct, silencer,
air cleaner, and/or air cleaner
element and baffle in air cleaner;
re-indexing of air cleaner.
Exhaust System Removal or rendering inoperative
exhaust system components
including the catalytic converter -
muffler assembly, inlet pipe, outlet
pipe, resonator and flexpipe.
Rotation of horizontal exhaust
system directional outlet pipe to
cause the exhaust to be emitted in
a direction other than downward.
Engine Cooling System Removal or rendering inoperative
the fan clutch. Removal or
modification of the fan shroud.
Replacing a fixed fan with a fan of
increased diameter, different
number of blades or different pitch
width.
MAINTENANCE
Instructions for maintenance and service of the noise control system
have been included in the Required Maintenance Services and in the
General Maintenance Checklist. To further help minimize noise emissions
degradation throughout the life of the vehicle, Ford Motor Company
recommends that this vehicle should be operated in the manner
described within the Owner Guide. Caution should be exercised by the
owner when installing replacement parts to be sure that a tampering act
(as outlined above) is not committed. Note any inspection and service
performed in the Maintenance Record.
EMISSIONS INFORMATION LABEL
Emissions information appears on the Important Engine Information
Decal located on or near the engine.
2004 F650/750(f67)
Supplement
USA English(fus)
General maintenance information
225

SCHEDULED MAINTENANCE SERVICES
Maintenance service adjustments must conform to specifications
contained in this manual, and those shown on the Important Engine
Information Decal. The following services are to be performed at
scheduled intervals because they are considered essential to the life and
performance of your vehicle. Ford recommends that you perform
maintenance on all designated items to achieve best vehicle operation.
Scheduled maintenance beyond 161,000 km (100,000 miles) should be
continued as before 161,000 km (100,000 miles).
SPECIAL OPERATING CONDITIONS
If your driving habitsfrequentlyinclude one or more the following
conditions:
•Short trips oflessthan 16 km (ten miles) when outside temperatures
remain below freezing.
•Operating duringhot weatherin stop-and-go“rush hour”traffic.
•Operating in severe dust conditions.
•Extensive idling, or low speed operation such as door-to-door delivery
service.
•High speed operation with a fully loaded vehicle (maximum GVW).
•Snowplowing.
Perform the following:
•Change engine oil and oil filter every three months, 8,000 km
(5,000 miles) or 125 hours of engine service.
•If operating in severe dust conditions, replace the air cleaner filter
more often than regular intervals as determined by the air filter
restriction indicator. Make sure that the air filter restriction indicator
is in good working order.
•Lube the manual transmission and the rear axle every 48,279 km
(30,000 miles) or 6 months, whichever comes first.
•See the Allison, Cummins and Caterpillar Operator’s Manual.
2004 F650/750(f67)
Supplement
USA English(fus)
General maintenance information
226

SCHEDULED MAINTENANCE GUIDE
MAINTENANCE SERVICES AND RECORD RETENTION
The maintenance record form which follows is for your convenience. In addition to recording the services performed, you should
retain copies of your receipts for the services. You also should keep records of any emission control systems maintenance
services performed on your vehicle.
Maintenance Record
Warranty
Start Date ______________________________________ Engine Displacement ______________________________________
Vehicle
Identification
Number _________________________________________ Owner Name ___________________________________________
IMPORTANT — This document should remain with the vehicle at all times.
2004 F650/750(f67)
Supplement
USA English(fus)
General maintenance information
228