303-01 FORD FIESTA 2007 Workshop Manual

303-01 B-32 Engine - 2.OL Duratec-HE (M14) 303-01 B-32
IN-VEHICLE REPAIR
24. Raise the vehicle. For additional N0TE:Make sure that the contact surface for the
information, refer to: (100-02 Jacking and CV joint boot on the intermediate shaft is clean. ,
Lifting)
Slide the inner CV joint boot onto the
Jacking (Description and Operation),
intermediate shaft. (..
Lifting (Description and Operation). Use a suitable screwdriver under the boot to
25. Remove the M6 x 18 mm bolt. allow air to escape.
26. Remove the special tool. 29. N0TE:lnstall a
new boot clamp.
Using a suitable grip wrench, install the inner
CV joint boot clamp.
27. Install the cylinder block lower blanking
plug.
30. N0TE:When installing a new engine front
cover, the crankshaft position sensor
(CKP
sensor) must be aligned using the tool
supplied.
28.
N0TE:Do not damage the boot of the inner
CV joint. Align
the
CKP sensor (engine shown
removed for clarity).
1. Loosen the CKP sensor bolts.
2006.0 Fiesta 1212006 G451288en
procarmanuals.com

303-01 B-33 Engine - 2.OL Duratec-HE (M14) 303-01 B-33
IN-VEHICLE REPAIR
2. Insert the tool supplied so that it engages 34. N0TE:lf necessary, install a new valve
with the teeth of the crankshaft pulley. cover gasket.
31. Install the CKP sensor (engine shown
removed for clarity).
1. Install the CKP sensor bolts.
2. Remove the tool.
Install the valve cover.
Tighten the bolts in the sequence shown.
35. Using the special tool, install the spark
plugs.
. Install the drive belt.
36. Using the special tool, connect the spark
For additional information, refer to:
plug connectors.
Accessory Drive Belt
- 2.OL Duratec-HE
(M14) (303-05 Accessory Drive, Removal
and Installation).
33. Apply sealant thinly on the areas shown.
-- - -- -
2006.0 Fiesta 1212006 G451288en
procarmanuals.com

303-01 B-34 Engine - 2.OL Duratec-HE (M14) 303-01 B-34
IN-VEHICLE REPAIR
37. Install the EVAP valve bracket. 40. Attach the positive crankcase ventilation
(PCV) hose to the valve cover.
/- r.
38. Install the air cleaner retainer.
41. Attach the engine wiring harness to the
valve cover.
1. Clip on the engine wiring harness at the
intake pipe.
2. Clip on the engine wiring harness bracket at
the intake pipe.
3. Install the air cleaner retainer.
4. Connect the power. steering fluid return line
to the retaining clip.
42. Install the air cleaner.
For additional information, refer to: Air
Cleaner
- 2.OL Duratec-HE (M14) (303-12
Intake Air Distribution and Filtering,
Removal and Installation).
43. Connect the battery ground cable.
For additional information, refer to: Battery
Disconnect
(414-01 Battery, Mounting and
Cables, General Procedures).
2006.0 Fiesta 1212006 G451288en
procarmanuals.com

303-01 B-35 Engine - 2.OL Duratec-HE (M14) 303-01 B-35 -- - - - - -
IN-VEHICLE REPAIR
Valve Seals(21 238 0)
Special Tool(s)
I I Compressor, Valve Spring I
Adapter for 303-361 A
303-36 1 -02 (2 1
- 1 55-02A)
Adapter, Air Supply (Cylinder
Head)
303-363 (2
I -1 57)
21157
I I Pliers, Valve Stem Seal
Removal
1. Remove the camshafts.
For additional information, refer to:
Camshafts (303-01 Engine
- 2.OL
Duratec-HE (M14), In-vehicle Repair). 2.
Using the special tool, apply
7 to 10 bar of
compressed air into the cylinder.
3. Remove the valve tappets and keep them in
order for reassembly.
4. Using the special tools, remove the valve
springs.
Compress the valve spring.
Remove the valve collets.
Release the valve spring.
Remove the valve spring retainer and the
valve spring.
5. Using the special tool, remove the valve
seals.
2006.0 Fiesta 1212006 G37453en
procarmanuals.com

303-01 B-36 Engine - 2.OL Duratec-HE (M14) 303-01 B-36
IN-VEHICLE REPAIR
Discard the valve seals. Release the valve spring.
Installation 3. Remove the special tools.
4. lnstall the valve tappets.
1. N0TE:lnstall new valve seals. 5. lnstall the camshafts. N0TE:Cover the valve collet groove on the valve
stem with a protective sleeve. For additional information, refer to:
Camshafts (303-01 Engine
- 2.OL Using the special tool, install the valve seals.
Duratec-HE (M14), In-vehicle Repair).
Remove the protective sleeve.
2. Using the special tools, install the valve
springs.
Install the valve spring retainer and the valve
spring.
Compress the valve spring.
Install the valve collets.
2006.0 Fiesta 1212006 G37453en
procarmanuals.com

303-01 B-37 Engine - 2.OL Duratec-HE (M14) 303-01 B-37
IN-VEHICLE REPAIR
Valves(21 2 1 5 4)
Adapter for 303-361 A
303-361 -02 (2 1-1 55-02A)
Special Tool(s)
I I Pliers, Valve Stem Seal I
21155
Removal
Compressor, Valve Spring
303-361 A (21 -1 55A)
1. Remove the cylinder head.
For additional information, refer to: Cylinder
Head (303-01 Engine
- 2.OL Duratec-HE
(M14), In-vehicle Repair).
2. Using the special tools, remove the valve
springs.
Compress the valve spring.
Remove the valve collets.
Release the valve spring.
Remove the valve spring retainer and the
valve spring.
3. Using the special tool, remove the valve
seals.
Discard the valve seals.
4. Remove the valves.
Installation
1. Install the valves.
2. N0TE:lnstall new valve seals.
N0TE:Cover the valve collet groove on the valve
stem with a protective sleeve.
Using the special tool, install the valve seals.
2006.0 Fiesta 12/2006 G37454en
procarmanuals.com

303-01 B-38 Engine - 2.OL Duratec-HE (M14) 303-01 B-38 - --
IN-VEHICLE REPAIR
Remove the protective sleeve.
3.
Using the special tools, install the valve
springs.
lnstall the valve spring retainer and the valve
spring.
Compress the valve spring
Install the valve collets.
Release the valve spring.
4. Remove the special tools.
5. lnstall the cylinder head.
For additional information, refer to: Cylinder
Head (303-01 Engine
- 2.OL Duratec-HE
(M14), Invehicle Repair).
2006.0 Fiesta 1212006 G37454en
procarmanuals.com

303-01 B-39 Engine - 2.OL Duratec-HE (M14) 303-01 B-39
IN-VEHICLE REPAIR
Special Tool(s)
I I Universal Flange Holding I
General Equipment
15030A
1~6 x 18 mm bolt I
Wrench
205-072
Materials
Name Specification
Removal
Hypoid Gear Oil
Silicone Sealant
1. Disconnect the battery ground cable.
SQM-2C9002-AA
WSE-M4G323-A4
For additional information, refer to: Battery
Disconnect
(414-01 Battery, Mounting and
Cables, General Procedures).
2. Remove the air cleaner.
For additional information, refer to: Air
Cleaner
- 2.OL Duratec-HE (M14) (303-12
Intake Air Distribution and Filtering,
Removal and Installation).
3. Detach the engine wiring harness from the
valve cover.
1. Unclip the power steering return line from the
engine wiring harness bracket.
2. Remove the air cleaner retaining bracket.
3. Unclip the engine wiring harness bracket
from the intake manifold.
4. Unclip the engine wiring harness from the
intake manifold.
4. Remove the positive crankshaft ventilation
(PCV) hose.
2006.0 Fiesta 1212006 G451293en
procarmanuals.com

303-01 B-40 Engine - 2.OL Duratec-HE (M14) 303-01 B-40
IN-VEHICLE
REPAIR
5. Disconnect the camshaft position (CMP) 8. Using the special tool, disconnect the spark
sensor electrical connector.
plug electrical connectors.
1.
6. Remove the air cleaner retaining bracket. 9. Using the special tool, remove the spark
plugs.
7. Remove the evaporative emission (EVAP)
valve support bracket.
10. Remove the valve cover.
11. Remove the accessory drive belt.
For additional information, refer to:
Accessory Drive Belt
- 2.OL Duratec-HE
(M14) (303-05 Accessory Drive, Removal
and Installation).
c
2006.0 Fiesta la2006 G451293en
procarmanuals.com

303-01 B-41 Engine - 2.OL Duratec-HE (M14) 303-01 B-41
IN-VEHICLE REPAIR
12. Raise and support the vehicle. For Remove and discard the constant velocity
additional information, refer to: (1 00-02 (CV) joint boot clamp.
I Jacking and Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
13. Disconnect the crankshaft position (CKP)
sensor electrical connector.
14. Disconnect the generator electrical
connectors.
Unclip the wiring harness.
16. N0TE:Only rotate the crankshaft in the
normal direction of rotation.
Rotate the crankshaft until piston No.
1 is
approximately 45 degrees before top dead
center (BTDC).
15.
N0TE:Do not damage the inner constant
velocity (CV) joint boot.
Detach the inner CV joint boot from the
intermediate shaft.
2006.0 Fiesta 1212006 G451293en
procarmanuals.com