brake sensor FORD FIESTA 2007 Workshop Manual

204-01 -2 Front Suspension 204-01 -2
SPECIFICATIONS
I Top mount retaining nuts I 25 I 18 I - I
Torque Specifications
I Thrust bearing retaining nut I 48 I 35 I - I
Stabilizer bar connecting link to strut and spring
retaining nut Ib-in
I Wheel
knuckle to suspension strut pinch bolt I 85 I 63 I - I
Ib-ft Item Nm
Brake caliper anchor plate retaining bolts
Lower arm ball joint to wheel knuckle retaining nut
I Steering gear retaining bolts I 48 I 35 I - I
Tie-rod end retaining nut
Stabilizer bar clamp retaining bolts
Stabilizer bar to connecting link retaining nut
Fb.wer arm front retaining bolt I
70
48
I Lower arm rear clamp retaining bolts I 55 I 41 I - I
48
55
55
I Crossmember front retaining bolts I 70 I 52 I - I
52
35
I Crossmember rear retaining bolts 1 Iq5 1 85 I - I
-
-
35
41
41
I Crossmember inner and outer retaining bolts 1 175 1 129 1 - I
-
-
-
I Wheel hub retaining nut 1290 1214 1 - I
I Engine support insulator center bolt I 48 I 35 I - I
2006.0 Fiesta 1212006 GI 52539en
Wheel speed sensor retaining nut
a) Refer to the procedure in this section.
9 - 80
procarmanuals.com

204-01 -3 Front Suspension 204-01 -3
DESCRIPTION AND OPERATION
Front Suspension
Overview
N0TE:During installation of the front wheel bearing
it is important to adhere to the specified installation
position, as the anti-lock brake system
( ABS )
sensor ring is located in the wheel bearing. A
coloured rubber ring is provided to indicate the
correct installation position. If the wheel bearing
were to be installed incorrectly then this would
cause failure of the ABS
.
A newly developed Mc-Pherson front suspension
with L-shaped lower arms is used. These lower
suspension arms are linked via large rubber
mountings to a reinforced and extremely rigid front
axle crossmember.
The ball head between the lower suspension arm
and the suspension strut is secured with three
rivets. Toe-in is adjusted via adjustable track rods.
The lower suspension arms can only be replaced as a complete unit.
2006.0 Fiesta IZIZOO~ GI 67080en
procarmanuals.com

204-01 -1 4 Front Suspension 204-01 -1 4
REMOVAL AND INSTALLATION
Detach the brake caliper and anchor plate N0TE:Use a 5 mm Allen key to prevent the ball
from the wheel knuckle. joint stud from rotating. f
6. Remove the brake disc.
Remove and discard the retaining washer (if
equipped).
Vehicles with anti-lock brakes
7. Detach the wheel speed sensor from the
wheel knuckle.
All vehicles
*= &AUTION:L~~~~ the tie-rod end retaining
nut in place to protect the ball joint stud. Loosen
the tie-rod end retaining nut.
k
&AuTl~N:~rotect the ball joint seal using
a soft cloth to prevent damage.
Using the special tool, detach the tie-rod end
from the wheel knuckle.
1. Release the tie-rod end.
2. Remove and discard the tie rod end retaining
nut.
/'-
lorn A~AuT10N:~rotect the ball joint seal
using a soft cloth to prevent damage.
Detach the lower arm ball joint from the
wheel knuckle.
2006.0 Fiesta 1212006 GI 83759en
procarmanuals.com

204-01 -1 6 Front Suspension 204-01 -1 6
REMOVAL AND INSTALLATION
Using the special tool, attach the wheel hub 5. AWARNING:lnstall a new tie-rod end to the halfshaft.
retaining nut. Failure to follow this f
3m ACAUTION:M~~~ sure the heat shield is
installed to prevent damage to the ball joint.
Install the heat shield.
4m &AUTION:T~~ lower arm pinch bolt must
be installed from the rear of the wheel
knuckle. instruction
may result in personal injury.

N0TE:Use a 5 mm Allen key to prevent the ball
joint stud from rotating.
Attach the tie-rod end to the wheel knuckle.
Vehicles with anti-lock brakes
6. Attach the wheel speed sensor to the wheel
knuckle.
Attach the lower arm ball joint to the wheel
knuckle.
All vehicles
7. Install the brake disc.
8m &AUTION:DO not twist the brake hose
when attaching the brake caliper to prevent
damage to the brake hose.
2006.0 Fiesta 1212006 GI 83759en
procarmanuals.com

204-02-2 Rear Suspension 204-02-2
SPECIFICATIONS
Torque Specifications
I Shock absorber upper mount retaining bolts I 25 I 18 I - I
Item
Shock absorber lower mount retaining bolt
I Trailing arm bushing retaining bolts I 125 1 92 I - I
Nm
115
I drum brakes I I I I
Beam axle retaining bolts
Wheel spindle retaining bolts
- Vehicles with rear
Wheel spindle retaining bolts
- Vehicles with rear
disc brakes
Ib-ft
85
I Wheel hub retaining nut 1 235 1 173 1 - I
I b-in
-
115
70
I Brake hose to brake caliper union I 15 I 11 I - I
I Brake tube to brake hose union I 15 I 11 I - I
85
52
I Wheel speed sensor retaining bolt I 9 I - I 80 I
-
-
2006.0 Fiesta 1212006 GI 52540en
procarmanuals.com

204-0214 Rear Suspension 204-02-4
DESCRIPTION AND OPERATION
suspension will not be correct. The installation .
orientation of the support bearing is indicated with
an arrow.
sensor pick-up ring
1 3 1 stub axle I
1 4 1 Brake back plate assembly with brake I
1 5 1 Bracket I
1 6 1 Spring I
1 7 1 Shock absorber I
A significant modification is the replacement of the
previous Mc-Pherson suspension struts with
separate spring and shock absorber elements. This
results in more space in the area of the suspension
strut turrets, thus increasing the volume of the
luggage compartment. In addition, the forces from
the spring and shock absorber elements are now
dissipated separately and have been individually
optimised.
The shock absorbers are single-tube gas shock
absorbers.
It is important that the correct installation orientation
is adhered to when assembling the support
bearings, as otherwise the geometry of the rear
- -
2006.0 Fiesta 1212006 GI 67083en
procarmanuals.com

204-02-1 0 Rear Suspension 204-02-1 0
REMOVAL AND INSTALLATION
Beam Axle(l5 231 0)
f
General Equipment 5. Detach the parking brake cable from the (.
beam axle bracket on both sides. I Transmission jack
I Securing strap I
I Electric hand drill I
I Blind rivet gun I
Removal
Vehicles with rear drum brakes
1. Release the parking brake.
2. Remove the rear wheels and tires.
For additional information, refer to: Wheel
and Tire (204.04 Wheels and Tires, Removal 6. Remove the brake dIIlm and wheel spindle
and Installation). assembly
on both sides.
3. Detach the rear wheel speed sensor and
brake hose retaining bracket from the beam
axle on both sides.
Remove the retaining bolt.
7m &AUTION:S~~~~~~ the brake backing
plate, wheel cylinder and brake shoes
assembly to prevent load being placed on
the brake hose.
4. Disconnect the parking brake cable on both
Detach the brake backing plate, wheel
sides. cylinder and brake shoes assembly from the
beam axle on both sides.
2006.0 Fiesta 1212006 G183767en
procarmanuals.com

204-02-1 1 Rear Suspension 204-02-1 1
REMOVAL AND INSTALLATION
Using a suitable electric hand drill, remove
the rivets.
Vehicles with rear disc brakes
8. Remove the brake disc shield.
For additional information, refer to: Brake
Disc Shield
(206-04 Rear Disc Brake,
Removal and Installation).
9. Detach the parking brake cable from the
beam axle bracket on both sides.
All vehicles
10. Detach the parking brake cable from the
beam axle on both sides.
11. Remove the rear wheel speed sensor.
For additional information, refer to: Rear
Wheel Speed Sensor
(206-09 Anti-Lock
Control, Removal and Installation).
I*' AWARNING:M~~~ sure that the beam axle
is secured to the transmission jack. Failure
to follow this instruction may result in
personal injury.
Using a suitable securing strap, secure the
beam axle to a transmission jack.
13. Detach the shock absorber from the beam
axle on both sides.
14. Detach the spring from the lower spring
seat on both sides.
15. Remove the beam axle.
2006.0 Fiesta 1212006 GI 83767en
procarmanuals.com

204-02-1 4 Rear Suspension 204102-14
REMOVAL AND INSTALLATION
14. Connect the parking brake cable on both 18. Tighten the shock absorber lower mounting
sides. bolt on both sides.
f
15. Attach the rear wheel speed sensor and 19. Adjust the parking brake cable.
brake hose retaining bracket to the beam
For additional information, refer to: Parking
axle on both sides.
Brake Cable Adjustment
- Vehicles With:
Install the retaining bolt. Rear Drum Brakes (206-05 Parking Brake
and Actuation, General Procedures).
16. Install the rear wheels and tires.
For additional information, refer to: Wheel
and Tire
(204-04 Wheels and Tires,
Removal and Installation).
All vehicles
17. Tighten the beam axle retaining bolts on
both sides.
2006.0 Fiesta 1212006 GI 83767en
procarmanuals.com

204-02-1 5 Rear Suspension 204-02-1 5
REMOVAL AND INSTALLATION
Wheel Spindle(l5 366 0)
ji t
' Removal
All vehicles
I. Remove the dust cap.
Vehicles with rear drum brakes
2. Remove the brake drum.
4. Remove the wheel spindle.
Vehicles with rear disc brakes
5. Remove the brake disc.
For additional information, refer to: Brake
Disc
(206-04 Rear Disc Brake, Removal and
Installation).
For additional information, refer to: Brake
6. Remove the wheel hub.
Drum
(206-02 Drum Brake, Removal and Remove and discard the wheel hub retaining ( Installation). nut.
3. Detach the wheel speed sensor from the
wheel spindle.
procarmanuals.com