air filter FORD FIESTA 2007 User Guide

303-00-20 Engine System - General Information 303-00-20
DIAGNOSIS AND TESTING
I9 Install the engine upper cover. Measure the compression pressure
2l Raise and support the vehicle. REFER to: - 1.25L Duratec-1 6V
(1 00-02 Jacking and Lifting) 6V (sigrna)/l .GL (
Jacking (Description and Operation),
Lifting (Description and Operation).
2l. Install the glow plug relay.
22 Install the radiator undershield.
23, Install the engine undershield.
Z. Lower the vehicle.
25 Reset the PCM fault memory.
I. Open the central junction box (CJB) and remove
the
fuel pump relay.
N0TE:The engine will start, run for a few seconds
and then stop.
2. Start the engine.
3. Remove the air
cleaner.
REFER to: Air Cleaner - 1.25L Duratec-1 6V
(Sigma)/l.4L Duratec-1 6V (Sigma)ll .6L ( Duratec-I 6V (Sigma) (303-1 2 Intake Air
Distribution and
Filtering, Removal and
Installation).
4. Disconnect the electronic ignition (El) coil
connector from the El coil.
- -- - - -
2006.0 Fiesta 1212006 GI 52554en
procarmanuals.com

303-00-22 Engine System - General Information 303-00-22
DIAGNOSIS AND TESTING
11. Install the fuel pump relay.
I2 Install the air cleaner.
REFER to: Air Cleaner - 1.25L Duratec-1 6V
(Sigma)/l.4L Duratec-16V (Sigma)/l .6L
Duratec-I 6V (Sigma) (303-1 2 Intake Air
Distribution and
Filtering, Removal and
Installation).
13 Using worldwide diagnostic system (WDS), clear
the fault codes from the PCM.
Measure the compression ressure
(Engine
- 1 .3L Duratec-8V P Rocam)) N0TE:Twist the spark plug connectors slightly
1. Open the
central junction box (CJB) and remove
the
fuel pump relay.
before disconnecting them. Pull on the connector
and not on the
cable.
5. Disconnect the spark plug connectors.
N0TE:The engine will start, run for a few seconds
and then stop. 6. Remove the spark plugs.
2. Start the engine.
3. Remove the air
cleaner.
REFER to: Air Cleaner - 1.3L Duratec-8V
(Rocam) (303-12 Intake Air Distribution and
Filtering, Removal and Installation).
N0TE:Operate the starter motor with wide open
throttle until the reading on the compression tester
stops rising.
7. Carry out the measurement in accordance with
the instructions
supplied with the measuring
device on every
cylinder using a suitable
4. Disconnect the electronic ignition (El) coil compression pressure recorder
with the suitable (:
electrical connector from the El coil. adapter.
2006.0 Fiesta 1212006 GI 52554en
procarmanuals.com

303-00-23 Engine System - General Information 303-00-23
DIAGNOSIS AND TESTING
8. Install the spark plugs.
9. Connect the spark plug connectors.
1Q Connect the El coil electrical connector to the
El coil. 11.
Install the fuel pump relay.
I2 Install the air cleaner.
REFER to: Air Cleaner
- 1.3L Duratec-8V
(Rocam) (303-1 2 Intake Air Distribution and
Filtering, Removal and Installation).
13 Using worldwide diagnostic system (WDS), clear
the fault codes from the PCM.
Measure the compression ressure
(Engine
- 2.OL Duratec-HE PMI~))
1. Open the central junction box (CJB) and remove
the fuel pump relay.
N0TE:The engine will start, run for a few seconds
and then stop.
2. Start the engine.
3. Remove the air cleaner.
REFER to: Air Cleaner
- 2.OL Duratec-HE (M14)
(303-1 2 Intake Air Distribution and Filtering,
Removal and Installation).
4. Disconnect
the electronic ignition (El) coil
electrical connector from the El coil.
2006.0 Fiesta 1212006 GI 52554en
procarmanuals.com

303-00-25 Engine System - General Information 303-00-25
DIAGNOSIS AND TESTING
11. Install the fuel pump relay.
-. 12 Install the air cleaner.
REFER to: Air Cleaner
- 2.OL Duratec-HE (M14)
(303-12 Intake Air Distribution and Filtering,
Removal and Installation).
13 Reset the PCM fault memory.
Measure the oil ressure (Engine - 1.4L
Duratorq-TDCi PDv) Diesel)
N0TE:The oil pressure depends on various factors
(engine speed, oil temperature, oil viscosity, extent
4m Attach the oil pressure gauge with the oil of oil filter contamination).
pressure gauge connector, and position it to
N0TE:Measure the oil pressure at the specified allow reading
from above.
engine speed.
5. Lower the vehicle.
I. Raise and support the vehicle. REFER to:
(1 00-02 Jacking and Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
6. N0TE:Measure the oil pressure at an oil
temperature of 410°C.
N0TE:OiI pressure at 2000 rpm: 2.3 to 3.7 bar.
Measure the oil pressure.
2. Disconnect the oil pressure switch electrical
7. Raise and support the vehicle. Engine
- 1.4L connector from the oil pressure switch.
Duratorq-TDCi (DV) Diesel
3. Remove the oil pressure switch.
Discard the washer.
8. Remove the oil pressure gauge and the oil
pressure gauge connector.
2006.0 Fiesta 1212006 GI 52554en
procarmanuals.com

Engine - 1.25L Duratec-I 6V (Sigma)ll.4L
303-01A-I 9 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-OIA-I 9
IN-VEHICLE REPAIR
Intake Manifold(21 183 0)
Removal 6. Remove the intake manifold lower retaining
bolt.
A WARNING:Do not smoke or carry lighted
tobacco or open flame of any type when
working on or near any fuel related
components. Highly flammable mixtures
are always present and may ignite. Failure
to follow these instructions may result in
personal injury.
1. Release the fuel system pressure. For
additional information, refer to
Section
31 0-00 [Fuel System - General
Information].
2. Disconnect the battery ground cable. For
additional information, refer to
Section
414-01 [Battery, Mounting and 7. Disconnect the engine wiring harness
Cables]. electrical connector.
3. Remove the air cleaner. For additional
information, refer to Section
303-1 2 [Intake
Air Distribution and Filtering].
4. Detach the power steering fluid reservoir
from the bracket and position
it to one side.
5. Remove the accessory drive belt. For
additional information, refer to
Section
303-05 [Accessory Drive].
8. Disconnect the positive crankcase ventilation
(PCV) hose from the PCV.
2006.0 Fiesta 1212006 GI 83728en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-26 Duratec-1 6V (Sigma)Il.GL Duratec-1 6V (Sigma) 303-01 A-26
IN-VEHICLE REPAIR
16. Connect the evaporate emission (EVAP)
hose to the EVAP valve.
17. Connect the brake booster vacuum line to
the intake manifold.
19. Connect the engine wiring harness
electrical connector.

20. Install the intake manifold lower retaining
bolt and the generator bracket retaining
bolts.
18. Connect the positive crankcase ventilation
(PCV) hose to the PCV.
21. Install the accessory drive belt. For
additional information, refer to
Section
303-05 [Accessory Drive].
22. Attach the power steering fluid reservoir to
the bracket.
23. Install the air cleaner. For additional
information, refer to Section
3031 2 [Intake
Air Distribution and Filtering].
2006.0 Fiesta 1212006 GI 83728en
procarmanuals.com

Engine - I .25L Duratec-1 6V (Sigma)llm4L
303-01 A-28 Duratec-1 6V (Sigma)llm6L Duratec-1 6V (Sigma) 303-01 A-28
IN-VEHICLE REPAIR
Valve Cover(21 141 0)
Materials 4. Remove the valve cover. (. ,
Name Specification
I Silicone grease IESE-MlC171-AA I
Removal
A WARNING:Do not smoke or carry lighted
tobacco or open flame of any type when
working on or near any fuel related
components. Highly flammable mixtures
are always present and may ignite. Failure
to follow these instructions may result
in
personal injury.
1. Disconnect the battery ground cable. For
additional information, refer to
Section
414-01 [Battery, Mounting and
Cables].
2. Remove the air cleaner. For additional
information, refer to Section
303-12 [Intake
Air Distribution and Filtering].
3. Disconnect the spark plug electrical
connectors and detach the wires from the
valve cover.
Installation
1. N0TE:Check the valve cover gasket for
damage and install a new valve cover gasket
if necessary.
N0TE:lnstall the stud bolts to positions 5 and 6.
Install the valve cover.
Tighten the bolts in the sequence shown in
three stages.
Stage 1: Tighten bolt 1 by 3 to 4 turns.
Stage 2: Tigthen bolts 1 through 13 to 3 Nm.
Stage 3: Tigthen bolts 1 through 13 to 9 Nm.
2m ACAUTION:~~~ a suitable blunt object to
avoid damage to the spark plug connector
gasket. Coat the inside of the spark plug
connector with silicone grease to depth of
5-10 mm.
- - --
2006.0 Fiesta 1212006 GI 83729en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llI4L I 303-01 Am29 Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma) 303-01 A-29
IN-VEHICLE REPAIR
Connect the spark plug electrical connectors
and attach the wires to the valve cover.
3. Install the air cleaner. For additional
information, refer to Section 303-1
2 [Intake
Air Distribution and Filtering].
4. Connect the battery ground cable. For
additional information, refer to
Section 414-01 [Battery, Mounting and
Cables].
2006.0 Fiesta 1212006 GI 83729en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llI4L
303-0 1 A-47 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-01 A-47
IN-VEHICLE REPAIR
Exhaust Manifold(21 187 0)
i Special Tool(s1 2. Remove the air cleaner.
--
Adapter for 303-290A
303-290-01 (21 -1 40-01
)
Adapter for 303-290A
303-290-02 (21 -1 40-02)
21 14002
General Equipment
21 14003
I Exhaust wrap I
Adapter for 303-290A
303-290-03A (21
-1 40-03A)
Removal
For additional information, refer to: Air
Cleaner - 1.25L Duratec-1 6V (Sigma)llm4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V
(Sigma) (303-12 Intake Air Distribution and
Filtering, Removal and Installation).
3. Raise and support the vehicle.
For additional information, refer to: Lifting
(100-02 Jacking and Lifting, Description
and Operation).
4m ACAUTION:~~~~ bending of the exhaust
flexible pipe may cause damage resulting in
failure.
Support the exhaust flexible pipe with a
support wrap or
suitable splint.
5. Detach the exhaust flexible pipe from the
catalytic converter.
Discard the gasket and the nuts.
1. Disconnect the battery ground cable. - -
For additional information, refer to: Battery 6.
Detach the exhaust system insulators from
Disconnect
(414-01 Battery, Mounting and the
exhaust brackets and position it to one
Cables, General Procedures). side.
2006.0 Fiesta 12/2006 GI 83739en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-53 Duratec-1 6V (Sigma)/l .6L
Duratec-1 6V (Sigma) 303-01 A-53
IN-VEHICLE REPAIR
22. Lower the vehicle.
23. Install the air cleaner.
' For additional information, refer to: Air
Cleaner - 1.25L Duratec-1 6V (Sigma)llm4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V
(Sigma) (303-1 2 Intake Air Distribution
and
Filtering, Removal and Installation).
24. Connect the battery ground cable.
For additional information, refer to: Battery
Disconnect
(414-01 Battery, Mounting and
Cables, General Procedures).
2006.0 Fiesta 1212006 GI 83739en
procarmanuals.com