cover gasket FORD FIESTA 2007 User Guide

303-01 B-I 05 Engine - 2.OL Duratec-HE (M14) 303-01 B-105 -- -
ASSEMBLY
57. Install the accessory drive belt idler pulley. Tighten the bolts in the sequence shown.
58. 1 nstall the accessory drive belt tensioner. 61 Install the evaporative emission (EVAP)
valve support bracket.
59. Apply a small bead of sealant to the areas
as shown.
62. Using the special tool, install the spark
plugs.
60. N0TE:lnstall a new valve cover gasket if
necessary.
Install the valve cover.
2006.0 Fiesta 1212006 G451310en
procarmanuals.com

Engine Cooling - 1.3L Duratec-8V
(Rocam)ll.25L Duratec-1 6V (Sigma)llI4L
303-03A-22 Duratec-1 6V (Sigma)lIl6L Duratec-1 6V (Sigma) 303-03A-22
REMOVAL AND INSTALLATION
9. Remove the generator.
For
additional information, refer to:
Generator
- 1.25L Duratec-1 6V (Sigma)/l.4L
Duratec-I 6V (Sigma)/l .6L Duratec-I 6V
(Sigma)
(414-02 Generator and Regulator,
Removal and Installation).
10. Remove the water pump pulley.
Discard the gasket.
Vehicles built 0412005 onwards
13. Remove the timing belt.
For additional information, refer to: Timing
Belt (303-01 Engine - 1.25L Duratec-1 6V
(Sigma)ll.4L Duratec-1 6V (Sigma)ll .6L
Duratec-1 6V (Sigma), ln-vehicle Repair).
11. Remove the timing belt cover (cover shown 14. Drain the cooling system,
removed for clarity). For additional information, refer to: Cooling
12' &AUTION:P~~~~~~ the timing belt and
lower cover from contamination by the
coolant.
Remove the water pump. System
Draining,
Filling and Bleeding -
1.3L Duratec-8V (Rocam)ll.25L
Duratec-1 6V (Sigma)ll.4L Duratec-1 6V (,
(Sigma)ll .6L Duratec-1 6V (Sigma) (303-03
Engine
Cooling - 1.3L Duratec-8V
(Rocam)ll.25L Duratec-I 6V (Sigma)/l.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V
(Sigma), General Procedures).
15. Remove the water pump and the timing
belt
tensioner.
Discard the gasket.
2006.0 Fiesta 1212006 GI 89080en
procarmanuals.com

Engine Cooling - 2.OL Duratec-HE (M14)
DIAGNOSIS AND TESTING
Symptom Possible Sources
Action
I Accessory drive belt. CHECK the condition of the
accessory drive belt.
REFER to: Accessory Drive
(303-05 Accessory Drive,
Diagnosis and Testing).
Cooling fan.
CHECK the operation of the
I cooling fan. REFER to WDS.
Engine. INSPECT the engine, cylinder
head, cylinder block and
cylinder head gasket.
REFER to: Cylinder Head
(303-
01 Engine - I .3L Duratec-8V
(Rocam), I n-vehicle Repair).
The engine does not reach
normal operating temperature. CHECK the ECT sensor.
I REFER to WDS.
Temperature gauge. CHECK the instrument cluster
engine temperature gauge.
REFER to: lnstrument Cluster
- Vehicles Built Up To:
1012005 (41 3-01 lnstrument
Cluster, Diagnosis and
Testing)
I lnstrument Cluster - Vehicles
Built From:
1012005 (41 3-01
lnstrument Cluster, Removal
and Installation).
Thermostat. CARRY OUT the Thermostat
Test Component Test in this
section. INSTALL a new ther-
mostat housing and thermostat
housing gasket as necessary.
REFER to: Thermostat Housing (303-03 Engine Cooling
-
2.OL Duratec-HE (M14),
Removal and Installation).
Component Tests
Pressure Test
A WARNING:When releasing the cooling
system pressure, cover the coolant
expansion tank cap with a thick cloth to
- prevent the possibility of coolant scalding.
Failure to follow this instruction may result
in personal injury.
N0TE:lf the coolant expansion tank cap is rotated
counterclockwise by 1 12 a full turn, the pressurized
coolant will be vented to the underside of the
coolant expansion tank cap.
1. Remove the coolant expansion tank cap.
2. Install the special tools 303-396 and 303-396-01
to the coolant expansion tank.
3. Pressurize the system to the coolant expansion
tank cap release pressure.
REFER to: Specifications (303-03 Engine
Cooling
- 2.OL Duratec-HE (M14),
Specifications).
2006.0 Fiesta 1212006 G426582en
procarmanuals.com

Automatic Transmission/Transaxle -
Vehicles With: 4-Speed Automatic
Transmission (AW81-40)
REMOVAL AND INSTALLATION
17. Disconnect the ignition switch to starter Support
the exhaust flexible pipe with a
motor solenoid and battery to starter motor suitable
support wrap or suitable splint.
solenoid cables.
21. Detach the exhaust flexible pipe from the
18. Remove the accessory drive belt cover. catalytic
converter.
Discard the nuts and the gasket.
19. Remove the engine support insulator.
22m &AUTION:L~~~~ the tie-rod end retaining
nut in place to protect the ball joint stud.
N0TE:Use a 5mm Allen key to prevent the ball
joint stud from rotating.
20m ACAUTION:~~~~ bending of the exhaust
flexible pipe may cause damage resulting
in failure. Loosen
the right-hand tie-rod end retaining
nut.
2006.0 Fiesta 1212006 G371506en
procarmanuals.com