303-01A FORD FIESTA 2007 Owner's Manual

303-01 A-I 26 Engine
- 1.25L Duratec-I 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L
Duratec-1 6V (Sigma) 303-01A-I26
INSTALLATION
23. Attach the air conditioning (NC)
compressor to the
cylinder block.
27. Connect the reversing lamp switch
electrical connector.
I
24. Connect the NC compressor clutch
28. Connect the crankshaft position (CKP)
electrical connector. sensor electrical connector.
25. Install the accessory drive belt. 29. Connect the oil pressure switch electrical
For
additional information, refer to: connector.
Accessory Drive
Belt - I .4L Duratec-16V
(Sigma)ll .6L Duratec-1 6V (Sigma),
Vehicles With: Air Conditioning (303-05
Accessory Drive,
Removal and
Installation).
26. Connect the starter motor electrical
connectors.
30.
N0TE:lnstall new exhaust flange nuts and
a new exhaust
flange gasket.
2006.0 Fiesta 1212006 Gll3164en
procarmanuals.com

Engine - 1.25L Dura
303-01 A-I 28 Duratec-16V
(Sigma)/l .r
:eel 6V (Sigma)ll.4L
L
Duratec-1 6V (Sigma) 303-01A-128
INSTALLATION
37. Connect the gearshift actuator electrical All vehicles
connector (colored black). 41. Lower the vehicle.
42. Tighten the engine front mount retaining
nuts and bolts.
38. Install the gearshift actuator cover.
39. Connect the clutch slave cylinder supply
line.
Install the spring clip.
40. Bleed the hydraulic clutch system.
For additional information, refer to: Clutch
System Bleeding
- Vehicles With:
Automated Gearshift
(308-00 Manual
~ransmission/Transaxle and Clutch -
General Information, General Procedures).
43. N0TE:lnstall a new engine rear mount
center retaining nut.
Tighten the engine rear mount center
retaining nut.
44. Attach the power steering line support
bracket to the cylinder head.
2006.0 Fiesta 1212006 GII 31 64en
procarmanuals.com

303-01 A-I 29 Engine
- 1.25L Duratec-I
6V (Sigma)ll.4L
Duratec-I 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-01A-129
INSTALLATION
45. Attach the power steering line to the power 48.
Connect the engine coolant temperature
i steering pump mounting bracket. (ECT) sensor electrical connector.
46, Install the engine wiring harness support 49.
Connect the generator electrical
brackets. connectors.
Connect the engine ground cable.
50. Connect the air conditioning (AIC)
47. Connect the electronic ignition (El) coil lower-pressure
cut-off switch electrical
electrical connector. connector.
51. Install the right-hand
headlamp assembly.
For additional information, refer to:
Headlamp Assembly (41 7-01 Exterior
Lighting, Removal and Installation).
2006.0 Fiesta 1212006 GI 131 64en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llI4L
303-01A-I36 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303=01A=136
INSTALLATION
Install the engine rear mount center retaining
nut. Attach
the right-hand halfshaft and the
intermediate shaft to the transaxle.
f
12. Install the engine support insulator. 14. CAUTIONS:
13. CAUTIONS:
Asupport the halfshaft. The inner joint
must not be bent more than
18 degrees.
The outer joint must not be bent more than
45 degrees.
ADO not damage the halfshaft seal.
N0TE:lnstall a new center bearing cap and
locknuts.
ASupport the halfshaft. The inner joint
must not be bent more than
18 degrees.
The outer joint must not be bent more than
45 degrees.
ADO not damage the halfshaft seal.
A~ake sure the snap ring is correctly
seated.
N0TE:lnstall a new snap ring. c
Attach the left-hand halfshaft to the
transaxle.
15. Attach the lower arm to the wheel knuckle
on both sides (right-hand side shown).
2006.0 Fiesta lu2006 G380459en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01A-I42 Duratec-1 6V (Sigma)/l .6L Duratec-I 6V (Sigma)
INSTALLATION
48. Attach the engine ground cable to the
transaxle. 52.
Connect the generator electrical
connectors.
49. Connect the electronic ignition (El) coil
53. Connect the knock sensor
(KS) electrical
electrical connector. connector.
50. Connect the engine coolant temperature
54. Connect the EVAP electrical connector.
(ECT) electrical connector.
51. Install the right-hand
headlamp assembly.
For additional information, refer to:
Headlamp Assembly (41 7-01 Exterior
Lighting, Removal and Installation).
2006.0 Fiesta 1212006 G380459en
procarmanuals.com

Engine Emission Control - 1.3L Duratec-8V
(Rocam)llI25L Duratec-1 6V (Sigma)llm4L
303-O8A-7 Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma) 303-0844-7
REMOVAL AND INSTALLATION
Crankcase Vent Oil Separator
i
Removal
1. Remove the air cleaner. For additional
information, refer to Section
303-1 2 [Intake
Air Distribution and Filtering].
2. Remove the intake manifold. For additional
information, refer to Section 303-01A
[Engine
-- 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)llm6L Duratec-1 6V
(Sigma)] I 303-01 B [Engine -- 1.4L
Duratorq-TDCi (DV) Diesel] I 303-01 C [Engine
-- 1.3L Duratec-8V (Rocam)] I 303-01 D
[Engine
-- 2.OL Duratec-HE (M14)I 1 303-01 E
[Engine
-- 1.6L Duratorq-TDCi (DV) Diesel].
3. Remove the crankcase vent oil separater.
Discard the gasket.
Installation
I. N0TE:lnstall a new crankcase vent oil
separator gasket.
To install, reverse the removal procedure.
2006.0 Fiesta 1212006 G210048en
procarmanuals.com

Engine Emission Control - 2.OL Duratec-HE
303-08B-7
(MI41 303-08B-7
DIAGNOSIS AND TESTING
Symptom Possible Sources
Action
Worn or damaged engine
components. REFER to Section 303-01A
[Engine -- 1.25L Duratec-I 6V
(Sigma)/l.4L Duratec-1 6V
(Sigma)ll .6L Duratec-1 6V
(Sigma)] 1 303-01 B [Engine --
1.4L Duratorq-TDCi (DV)
Diesel] 1 303-01 C [Engine
--
1.3L Duratec-8V (Rocam)] I
303-01 D [Engine -- 2.OL
Duratec-HE (M 14)] 1 303-01 E
[Engine
-- 1.6L Duratorq-TDCi
(DV) Diesel].
2006.0 Fiesta 1212006 G334290en ~
procarmanuals.com