Electrical FORD FIESTA 2007 Service Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 2007, Model line: FIESTA, Model: FORD FIESTA 2007Pages: 1226, PDF Size: 61.26 MB
Page 348 of 1226

21 1-00-28 Steering System - General Information 21 ImOO-28
GENERALPROCEDURES
15. Using the special tool, connect the spark
minimize the possibility of aeration. The
plug wires.
steering fluid level must be checked with
the steering fluid cold.
Check the steering fluid level. Fill the power
steering fluid reservoir to the
MAX mark with
the appropriate steering fluid as necessary.
For additional information, refer to:
Specifications
(211 -00 Steering System -
General Information, Specifications).
16. Connect the CKP sensor electrical
connector.
17. N0TE:When filling the power steering fluid
reservoir, make sure that the steering fluid
is clean and not agitated prior to use. The
steering fluid must be poured slowly into
the power steering fluid reservoir to
minimize the possibility of aeration. The
steering fluid level must be checked with
the steering fluid cold.
Fill the power steering fluid reservoir to the
MAX mark with the appropriate steering fluid.
For additional information, refer to:
Specifications
(211 -00 Steering System -
General Information, Specifications).
18. Start the engine and slowly turn the
steering wheel from lock to lock.
19. Switch OFF the engine.
20. N0TE:When filling the power steering fluid
reservoir, make sure that the steering fluid
is clean and not agitated prior to use. The
steering fluid must be poured slowly into
the power steering fluid reservoir to
-- - - --
2006.0 Fiesta 12/2006 G458163en
procarmanuals.com
Page 363 of 1226

21 1-02-1 5 Power Steering 211-02-15
REMOVAL AND INSTALLATION
Allow the fluid to drain into a suitable Detach the power steering line from the
container. steering gear.
Discard the O-ring seal.
I
Right-hand drive vehicles 6. Disconnect the power steering pressure
(PSP) switch electrical connector. 9. N0TE:Note the position of the power steering
line to aid installation.
Detach the power steering line from the
steering gear.
Left-hand drive vehicles
7. Detach the steering gear return hose from - -
the pressure line. All vehicles
8. N0TE:Note the position of the power steering
line to aid installation.
10. Disconnect the power steering lines from
the steering gear valve body.
1. Remove the retaining bolt.
2. Rotate the clamp plate.
Allow the fluid to drain into a suitable
container.
2006.0 Fiesta 1212006 G91965en
procarmanuals.com
Page 366 of 1226

21 1-02-1 8 Power Steering 21 1-02-1 8
REMOVAL AND INSTALLATION
5. N0TE:Note the position of the power steering
line to aid installation.
Detach the power steering line bracket from
the engine block.
I
Detach the power steering line bracket from
the steering gear.
/-.
Right-hand drive vehicles
9. N0TE:Note the position of the power steering
6. Disconnect the power steering pressure line to aid installation.
(PSP) switch electrical connector.
Detach the power steering line bracket from
the steering gear.
Left-hand drive vehicles
7. Detach the steering gear return hose from
the pressure line.
8. N0TE:Note the position of the power steering
line to aid installation.
All vehicles
10. Disconnect the power steering lines from
the steering gear valve body.
1. Remove the retaining bolt.
2. Rotate the clamp plate.
Allow the fluid to drain into a suitable
container.
2006.0 Fiesta 1212006 G397028en
procarmanuals.com
Page 372 of 1226

211 -02-24 Power Steering 211 -02-24
REMOVAL AND INSTALLATION
2. Disconnect the power steering pressure
(PSP) switch electrical connector. Support
the exhaust flexible pipe with a
support wrap or splint.
3. Detach the steering gear heat shield from 6. ACAUTION:Twisting the exhaust flexible the steering gear.
pipe more than two degrees may cause
4. N0TE:Note the position of the power steering
pump to steering gear pressure line to aid
installation.
Detach the power steering pump to steering
gear pressure line from the steering gear.
5m &AUTION:O~~~ bending of the exhaust
flexible pipe may cause damage resulting in
failure. damage
resulting in failure.
N0TE:Use a pry-bar to prevent the exhaust flexible
pipe from twisting when removing the exhaust
flexible pipe to catalytic converter retaining nuts.
Remove the exhaust flexible pipe to catalytic
converter retaining nuts.
Discard the exhaust flexible pipe to catalytic
converter gasket and retaining nuts.
7m &AUTION:T~~~ care when removing the
exhaust hanger insulator to prevent damage.
2006.0 Fiesta 1212006 G458165en
procarmanuals.com
Page 377 of 1226

21 I -02-29 Power Steering 21 1 -02-29
REMOVAL AND INSTALLATION
16. Connect the PSP switch electrical
connector. 2. Locate the special tool onto the power
steering pump to steering gear pressure line
union and install the O-ring seal.
17. Install the front wheels and tires. 3. Connect the power steering pump to steering
For additional information, refer to: Wheel
gear pressure line to the power steering
and Tire
(204-04 Wheels and Tires,
Removal and Installation). Pump.
Item 1 Power steering pump pulley
1. N0TE:This step is only required if installing
a new power steering pump to steering gear
, pressure line.
, Push the new power steering pump to
steering gear pressure line into the new
power steering pump to steering gear
pressure line union until
it clips into place.
2m ACAUTION:~~~~ must be taken to prevent
dirt ingress.
Using the special tool, install a new O-ring
seal onto the power steering pump to
steering gear pressure line union.
1. Push the O-ring seal onto the special tool. 4.
Using
the special tool, install the power
steering pump pulley.
2006.0 Fiesta 1212006 G458165en
procarmanuals.com
Page 413 of 1226

21 1 -04-5 Steering Column 2 I I -04-5
REMOVAL AND INSTALLATION
Steering Column(l3 542 0)
Removal Disconnect the electrical connector.
1. Remove the driver air-bag module.
For additional information, refer to: Driver
Air Bag Module (501-20 Supplemental
Restraint System, Removal and
Installation).
2. Remove the instrument panel lower panel.
1. Remove the lower retaining screws.
2. Remove the upper retaining screws from the
stowage compartment.
3. Release the clip.
3. Detach the audio control switch from the
steering column lower shroud (if equipped).
Using a thin bladed screwdriver, release the
locking tang.
4. Remove the audio control switch (if
equipped).
5. N0TE:Turn the steering wheel to gain access
to the steering column upper shroud
retaining clips.
Detach the steering column upper shroud
from the steering column lower shroud (steering wheel shown removed for clarity).
1 . Using a thin bladed screwdriver, release the
two clips, (one each side).
2. Detach the shroud.
6. Remove the steering column lower shroud
(steering wheel shown removed for clarity).
1. Remove the retaining screws.
2006.0 Fiesta 1212006 GI 05654en
procarmanuals.com
Page 414 of 1226

2 1 1 -04-6 Steering Column 21 1 -04-6
REMOVAL AND INSTALLATION
2. Release the steering column locking lever. Depress the locking tangs.
1--
7. N0TE:Make sure that the road wheels are in 10. Disconnect the passive anti-theft system
the straight ahead position.
(PATS) transceiver, windshield
Centralize the steering and lock it in position. wiperlwasher
switch and clockspring
electrical connectors.
Depress the locking tangs.
8. Detach the steering column shaft from the
steering gear pinion.
Discard the retaining bolt. 11. Remove the steering column.
Discard the retaining nuts.
9. Disconnect the ignition switch and turn
signal electrical connectors.
Installation
1. WARNINGS:
2006.0 Fiesta 1212006 GI 05654en
procarmanuals.com
Page 420 of 1226

21 1-05-2 Steering Column Switches 21 1-05-2
REMOVAL AND INSTALLATION
Ignition Switch(36 424 0)
Removal 2. Detach the shroud.
I. Disconnect the battery ground cable. For
additional information, refer to
Section
414-01 [Battery, Mounting and
Cables].
2. Detach the audio control switch from the
steering column lower shroud (if equipped).
Using a thin bladed screwdriver, release the
locking tang.
3. Remove the audio control switch (if
equipped).
Disconnect the electrical connector.
.. N0TE:Turn the steering wheel to access the
steering column upper shroud retaining
clips.
Detach the steering column upper shroud
from the steering column lower shroud (steering wheel shown removed for clarity).
5. Remove the steering column lower shroud
(steering wheel shown removed for clarity).
1. Release the steering column locking lever.
2. Remove the retaining screws.
6. Disconnect the ignition switch electrical
connector.
1. Using a thin bladed screwdriver, release the 7m Remove the ignition two clips (one each side).
2006.0 Fiesta 1212006 GI 05656en
procarmanuals.com
Page 426 of 1226

303-004 Engine System - General Information 303-00-4
DIAGNOSIS AND TESTING
Engine
Special Tool(s)
Socket, Spark Plug
303-499
I Adhesive - Loctite 243 I WSK-M2G349A7 I
Materials
1. Verify the customer concern by operating the
system.
2. Visually inspect for obvious signs of mechanical
or electrical damage.
k.
Name S~ecification
Leaks from oil carrying
components or basic engine.
E47332
&
21211
CHECK for cracks in oil
carrying components of the
basic engine by means of a
leak test. INSTALL new
components or seals as
necessary.
2006.0 Fiesta 1212006 GI 52554en
Compression Test Adapter
303-1 052
Pliers, Valve Stem Seal
303-508
4. If the cause is not visually evident, verify the
symptom and refer to the Symptom Chart.
Symptom Chart Symptom Possible Sources Action
Visual
Inspection Chart
Loss of oil Mechanical
- Coolant
leaks
- Oil leaks
- Fuel system leaks
- Visibly damaged or
worn parts
- Loose or missing
nuts or bolts Electrical
- Fuse(s)
- Loose
or corroded
connector(s)
- Powertrain control
module
- Damaged or worn
switch(es)
Oil leaks on components that
are
eithei coated in oil them-
selves or on components local
to them.
Internal or external leak at the
oil cooler.
Leak at the crankshaft seal.
3. If an obvious cause for an observed or reported
concern is found, correct the cause (if possible)
before proceeding to the next step.
CHECK for evidence of oil
leaks on components. Use an
ultraviolet (UV) leak tester if an
oil leak is not evident, INSTALL
new gaskets or components as
required.
CHECK the coolant expansion
tank for a film of oil on the
coolant surface. INSTALL a
new oil cooler or oil cooler
gasket.
INSTALL a new crankshaft
seal.
procarmanuals.com
Page 436 of 1226

303-00-1 4 Engine System - General Information 303-00-1 4
DIAGNOSIS AND TESTING
Symptom
Possible Sources
Action
Timing belt or timing chain
incorrectly tensioned.
CHECK the timing belt or
timing chain tension. INSTALL
a new timing belt or timing
chain as necessary. REFER to:
Timing Belt (303-01 Engine
-
I .25L Duratec-1 6V
(Sigma)/l.4L Duratec-1 6V
(Sigma)/l .6L Duratec-1 6V
(Sigma), In-vehicle Repair),
Timing Chain (303-01 Engine
- 1.3L Duratec-8V (Rocam),
In-vehicle Repair),
Timing Chain (303-01 Engine
- 2.OL Duratec-HE (M14), In-
vehicle Repair),
Timing Belt
(303-01 Engine -
1.4L Duratorq-TDCi (DV)
Diesel, In-vehicle Repair),
Timing Belt (303-01 Engine
-
I .6L Duratorq-TDCi (DV)
Diesel, In-vehicle Repair).
Noisy running or engine noise
Engine components
- Pistons
- Piston rings
- Connecting rod big end,
main bearing or thrust
bearing journals
- Connecting rods bent or
damaged.
CHECK the engine compon-
ents for wear or damage. Make
sure all components are within
specification. INSTALL new
components as necessary.
Engine - Oil Leaks
NOTE: Before installing new gaskets or seals, make
sure that the fault is clearly established.
If the oil leak cannot be identified clearly by a visual
inspection, carry out an ultraviolet
(UV) test:
Ultraviolet (UV) Testing
1. Clean the engine and transmission with a
suitable cleaning fluid.
2. Pour the UV-test fluid in accordance with the
quantity specified by the manufacturer through
the oil filler neck into the engine and install the
oil filler cap.
A WARN1NG:Vehicles with manual transaxle,
shift the transaxle into Neutral. Failure to
follow this instruction may result in
personal injury.
3. Start the engine and let it run for about five
minutes. 4.
Switch off the engine.
N0TE:lf no leak can be found, road test the vehicle
under various loads and check the engine for leaks
again.
5. Check the engine for oil leaks using a suitable
UV lamp.
'
6. Rectify any leaks found and check the engine
for oil leaks.
Measure the compression pressure
N0TE:The powertrain control module (PCM)
receives an error message when the fuel pump
relay is removed or electrical components are
disconnected. This error message must be deleted
from the fault memory using WDS after completing
the compression test.
(' ,
'I N0TE:Valve clearance must be set correctly before
performing a compression test. Make sure the
engine is at the normal operating temperature.
2006.0 Fiesta 1212006 GI 52554en
procarmanuals.com