DRIVE SHAFT FORD FIESTA 2007 Manual PDF

Automatic Transmission/Transaxle -
Vehicles With: 4-Speed Automatic
Transmission
(AW81-40)
DESCRIPTION AND OPERATION
1 3 1 I st - 3rd gear clutch I
Item Description
1 4 1 Small sun gear I
1
2
-
1 6 1 Planet gear carrier I
From the torque converter
Transmission input shaft
10 Annulus and output wheel
of the planetary
1 lgearset
I 11 I Intermediate gear stage I
1 12 1 Differential assembly I
)I 2nd - 4th gear brake I
1 14 12nd gear one-way clutch I
1 15 1 Large sun gear I
1 17 1 3rdl4th gear clutch I
I A I Planetary gearset, rear I
I B I Planetary gearset, front I
The drive is transmitted from the torque converter
(I) on the one hand to the transmission input shaft
(2) and via the 1st-3rd gear clutch (3) to the small
sun gear
(4), and on the other hand from the
transmission input shaft via the
3rdl4th gear clutch
(17) to the planet gear carrier (6).
As the drive is transmitted to two components
simultaneously, there are no relative movements
within the planetary
gearset. The planetary gearset
rotates as a complete unit.
N0TE:The 2nd-4th gear brake (1 3) remains
engaged, but the large sun gear
(I 5) can rotate in
the same direction of rotation as the output from
the engine by means of the 2nd gear one-way
clutch
(14), as a result of which the 2nd-4th gear
brake has no influence on the transmission ratio.
The Annulus (1
0) is fixedly connected to the output
wheel of the planetary
gearset and drives the
intermediate gear stage (1 1
) in the opposite
direction of rotation to the output from the engine.
The intermediate gear stage drives the differential
assembly (12) in the same direction of rotation as
the output from the engine.
2006.0 Fiesta 1212006 G380528en
procarmanuals.com

Automatic Transmission/Transaxle -
Vehicles With: 4-Speed Automatic
307-01 -25 Transmission (AW81-40) 307-01 -25
DESCRIPTION AND OPERATION
Item Descriotion
I 1 I From the torque converter I
~l%ansmission input shaft I
1 4 1 Small sun gear I
1 6 1 Planet gear carrier I
1 8 1Short planet gear I
1 9 1 Long planet gear I
10 Annulus and
output wheel of the planetary
/ (gearset
I 11 I Intermediate gear stage I
1 12 1 Differential assembly I
1 13 12nd - 4th gear brake I
1 14 1 2nd gear one-way clutch I
1 15 1 Large sun gear I - --
1 16 14th gear brake I
1 17 1 3rdl4th gear clutch I
~Iianetary gearset, rear I
I B I Planetary gearset, front I
Drive is transmitted from the torque converter (I)
to the transmission input shaft (2) and via the
3rdl4th gear clutch (1 7) to the planet gear carrier
(6).
The large sun gear (15) is held by the 4th gear
brake
(16), the 2nd gear one-way clutch (14) and
the 2nd-4th gear brake
(1 3).
N0TE:The short planet gears (8) and the small
sun gear (4) co-rotate, but they have no influence
on the transmission ratio.
The long planet gears (9) drive the annulus (10) in
the same direction of rotation as the output from
the engine.
The annulus is fixedly connected to the output
wheel of the planetary
gearset and drives the
intermediate gear stage
(11) in the opposite
direction of rotation to the output from the engine.
The intermediate gear stage drives the differential
assembly
(12) in the same direction of rotation as
the output from the engine.
2006.0 Fiesta 1212006 G380528en
procarmanuals.com

Automatic Transmission/Transaxle -
Vehicles With: 4-Speed Automatic
307-01 -27 Transmission (AW81-40) 307-01 -27
DESCRIPTION AND OPERATION
Item Description
I 1 I From the torque converter I
1 2 I Transmission input shaft I
1 4 ISmaII sun gear I
11 Planet gear carrier I
1 7 1 Reverse gear brake I
1 8 1Short planet gear I
1 9 1 Long planet gear I
10 Annulus and output wheel
of the planetary
I (gearset
I 11 I Intermediate gear stage I
1 12 1 Differential assembly I
1 15 1 Large sun gear I
1 18 1 Reverse gear clutch I
I A I Planetary gearset, rear I
I B I Planetary gearset, front I
Drive is transmitted from the torque converter (1)
to the transmission input shaft
(2) and via the
r reverse gear clutch (1 8) to the large sun gear (1 5).
The planet gear carrier
(6) is held by the reverse
gear brake
(7).
The large sun gear drives the long planet gears
(9) in the opposite direction of rotation to the output
from the engine.
N0TE:The short planet gears (8) and the small
sun gear (4) co-rotate, but they have no influence
on the transmission ratio.
The long planet gears drive the annulus (1
0) in the
opposite direction of rotation to the output from the
engine.
The annulus is fixedly connected to the output
wheel of the planetary
gearset and drives the
intermediate gear stage (I
I ) in the same direction
of rotation as the output from the engine.
The intermediate gear stage drives the differential
assembly (1 2) in the opposite direction of rotation
to the output from the engine.
2006.0 Fiesta 1212006 G380528en
procarmanuals.com

Automatic Transmission/Transaxle -
Vehicles With: 4-Speed Automatic
Transmission (AW81-40)
DESCRIPTION AND OPERATION
Item Description
1 5 1 Generic Electronic Module (GEM) I
I
1 6 1 Turbine Shaft Speed (TSS) sensor I
1 7 1 Output Shaft Speed (OSS) sensor I
1
2
3
4
l tem Description
Transmission control unit
Data Link Connector (DLC)
Powertrain Control Module (PCM)
Instrument cluster
1 8 I Transmission Range (TR) sensor I
1 9 1 Starter inhibit relay I
1 10 1 Backup lamp relay I
11 Transmission Fluid Temperature (TFT)
I I sensor
1 12 loverdrive switch I
1 13 1 Driver's side door ajar switch I
1 14 1 Solenoid valves in the main control body 1
Transmission control unit
Item Description
Electrical connector, vehicle wiring
harness
connector, transmission wiring
harness
--
The transmission control unit is located in the
'engine compartment on the left-hand side member.
The transmission control unit evaluates incoming
signals and controls the actuators accordingly.
2006.0 Fiesta 1212006 G380530en
procarmanuals.com

Automatic Transmission/Transaxle -
Vehicles With: 4Speed Automatic
307-01 -33 Transmission (AW81-40) 307-01 -33
DESCRIPTION AND OPERATION
This is influenced by the following variables: Vehicle
speed,
Engine load, Transmission fluid temperature.
Accelerator pedal position, The following are actuated:
Transmission input speed, SSA shift solenoid valve,
Vehicle speed,
Transmission fluid temperature,
Selector lever position.
The
following are actuated:
Main
regulating valve.
Reverse gear safety strategy
SSB shift solenoid valve.
Torque reduction when pulling away
In order to protect the clutches against excessively
high torque when pulling away, the PCM reduces
the engine torque in response to a request from
the transmission
control.
If the accelerator pedal is depressed while the
The transmission control unit prevents shifts into vehicle is pulling away, then the transmission reverse gear while the vehicle is driving forwards, control unit sends a corresponding signal as otherwise serious transmission damage can be requesting a torque reduction via the CAN databus. caused.
The reverse gear safety strategy is active when This
is influenced by the
following variables:
reverse gear is engaged with the selector lever at ' Selector lever position,
vehicle speeds in excess of 11 kmlh. Accelerator pedal position,
In this
case the transmission control unit actuates ' Engine speed,
the shift timing solenoid valve, as a result of which Transmission input speed,
the actuating pressure does not reach the reverse
. Vehicle speed. gear clutch or the reverse gear brake.
The following are actuated:
The reverse gear safety strategy is deactivated
PCM (torque reduction request signal via the
when the vehicle speed is below 9 kmlh. The
actuating pressure can then reach the reverse gear CAN
databus).
clutch and the reverse gear brake and the gearshift
into reverse gear is performed.
Selector lever positions
This is influenced by the following variables:
Vehicle speed,
Selector lever position.
The
following are actuated:
Shift timing solenoid valve.
Selector lever position "P"
No gear is engaged in selector lever position "P".
The parking
pawl is engaged manually via the
selector lever cable and the selector shaft.
Avoidance of gearshift judder during
engagement of a transmission range Selector
lever position "R"
In order to prevent gearshift judder when moving The reverse gear is eWaged in selector lever
the selector lever from N to D, the transmission position "R.
control unit initially shifts into
2nd gear instead of
1 st gear, and then immediately shifts back into I st
gear before the gearshift process is finished. Selector lever position "N"
This reduces the amount of gearshift judder during No gear is engaged in selector lever position WNW. engagement of a forward drive range.
The powertrain is not blocked. This is influenced by the following variables:
Selector lever position,
Accelerator pedal position,
Transmission input speed,
2006.0 Fiesta 1212006 G380530en
procarmanuals.com

Automatic Transmission/Transaxle -
Vehicles With: 4Speed Automatic
307-01 -35 Transmission (AW81-40) 307-01 -35
DESCRIPTION AND OPERATION
Engine speed
1 The engine speed is detected by the crankshaft
position (CKP) sensor and passed on to the PCM.
The engine speed is transmitted from the PCM via
the CAN
databus to the transmission control unit.
The transmission control unit uses this signal for:
Torque reduction during gearshifts,
Pressure control during gearshifts.
Engine load
The PCM determines a load signal which is
transmitted via the CAN
databus to the
transmission control unit.
The transmission control unit uses this signal for:
Torque reduction during gearshifts,
Pressure control during gearshifts,
Shift timing adaptation during upshifts,
Shift timing adaptation during shifts from 3rd to
4th gear,
Hill climb mode,
( ' Hill descent mode. ' ,
Torque reduction request signal
Before performing a gearshift, the transmission
control unit sends a signal via the CAN
databus to
the PCM requesting a torque reduction.
The PCM then reduces the engine torque, ensuring
that the gearshift is as smooth and judder-free as
possible.
Brake signal
The PCM receives a signal from the stoplamp
switch when the brake pedal is depressed.
This signal is transmitted via the CAN
databus to
the transmission control unit.
The transmission control unit uses this signal for:
Gearshift control,
Engagement of the TCC
Accelerator pedal position
The PCM receives the current accelerator pedal
position signal from the Accelerator Pedal Position
(APP) sensor.
This signal is transmitted via the CAN
databus to
the transmission control unit.
The transmission control unit uses this signal for:
Controlling the main line pressure,
Gearshift control,
Engagement of the TCC,
Shift timing adaptation during upshifts,
Shift timing adaptation during shifts from 3rd to
4th gear,
Shift timing adaptation during shifts from 4th to
3rd gear,
Avoidance of gearshift judder during
engagement of a transmission range,
Torque reduction when pulling away.
Coolant temperature
The coolant temperature is detected by the Engine
Coolant Temperature (ECT) sensor and passed
on to the PCM.
This signal is transmitted via the CAN
databus to
the transmission control unit.
The transmission control unit uses this signal for:
Cold start mode,
Engagement of the TCC
Selector lever position
The transmission control unit transmits the selector
lever position to the instrument cluster.
The instrument cluster uses the signal to send a
request for a warning tone to the GEM when the
selector lever is not in position "P" and the driver's
door is opened.
-
2006.0 Fiesta 1212006 G380530en
procarmanuals.com

Automatic Transmission/Transaxle -
Vehicles With: 4-Speed Automatic
307-01 -58 Transmission
(AW81-40) 307-01 -58
IN-VEHICLE REPAIR
Halfshaft Seal LH
I. 1.NOTE:lnstall a new halfshaft seal.
Special
Tool(s) Discard
the seal.
Removal
Installer, Front Wheel Hub
Seal
204-066 (1 4-028)
Remover, Halfshaft Seal
308-208 (1 6-074)
A WARN1NG:Refer to the Material Safety Data
Sheets for the Automatic Transmission
Fluid
E-AW. Failure to follow this
instruction may result in personal injury.
Certain Transmission and Power Steering
fluids supplied to Ford contain additives
which may cause skin irritation or other
skin reactions after contact.
Installation
For additional information, refer to: Health
and Safety Precautions
(1 00-00 General
Information, Description and Operation).
See
- Transmission Fluids. Using the
special tool, install the halfshaft
seal.
1. Remove the left-hand halfshaft.
2. Install the left-hand halfshaft.
For additional information, refer to: Front
Halfshaft LH
(205-04 Front Drive Halfshafts, For additional
information, refer to: Front
Removal and lnstallation). Halfshaft
LH (205-04 Front Drive Halfshafts,
Removal and lnstallation).
2. Using the special tool, remove the halfshaft
seal.
Allow the fluid to drain into a suitable
container.
For additional information, refer to: Health
and Safety Precautions
(1 00-00 General
Information, Description and Operation).
See
- Transmission Fluids.
-
2006.0 Fiesta 1212006 G371503en
procarmanuals.com

Automatic Transmission/Transaxle -
Vehicles With: 4-Speed Automatic
307-01 -59 Transmission (AW81-40) 307101 -59
IN-VEHICLE REPAIR
Halfshaft Seal RH
Special Tool@) Discard the seal.
Installer, Front Wheel Hub
Seal
204-066
(1 4-028)
A WARNING:Refer to the Material Safety Data
Sheets for the Automatic Transmission
Fluid E-AW. Failure to follow this
( instruction may result in personal injury. ' , Certain Transmission and Power Steering
fluids supplied to Ford contain additives
which may cause skin irritation or other
skin reactions after contact.
For additional information, refer to: Health
and Safety Precautions (100-00 General
Information, Description and Operation).
See
- Transmission Fluids.
Remover, Halfshaft Seal
308-208
(1 6-074)
1. Remove the right-hand halfshaft. 2. Install the right-hand halfshaft.
For additional information, refer to: Front
Halfshaft
RH (205-04 Front Drive Halfshafts, For
additional information, refer to: Front
Removal and Installation). Halfshaft
RH (205-04 Front Drive Halfshafts,
Removal and lnstallation).
2. Using the special tool, remove the halfshaft
seal.
lnstallation
1. N0TE:lnstall a new halfshaft seal.
Allow the fluid to drain into a suitable
container.
Removal Using the special tool, install the halfshaft
seal.
For additional information, refer to: Health
and Safety Precautions
(1 00-00 General
Information, Description and Operation).
See
- Transmission Fluids.
2006.0 Fiesta 1212006 G371504en
procarmanuals.com

308-0314 Manual Transmission/Transaxle 308-03-4 -- --
SPECIFICATIONS
2006.0 Fiesta 1212006 GII 3289en
Item
Transaxle housing final drive cover retaining bolts
Transaxle to engine retaining bolts
Engine support insulator to engine retaining bolt
Engine support insulator to
subframe retaining bolts
Engine rear mount outer retaining nuts
Exhaust flexible pipe retaining nuts
Wiring harness retaining bracket retaining nut Power steering high-pressure line retaining bracket
retaining bolt
Lower arm ball joint to the wheel knuckle retaining
nut
Engine rear mount center retaining nut
Intermediate shaft center bearing retaining nuts
Strut and spring assembly top mount retaining nuts
Transmission fluid filler plug
Starter motor retaining bolts
Starter motor wiring harness retaining bracket retaining nuts Nm
12
47
48
48
48
44
22
25
52
90
25
48 35
35
20
Ib-ft
9
35
35
35
35
32
16
21
38
66
18
35
26
26
15
I b-in
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
procarmanuals.com

308-0318 Manual Transmission/Transaxle 308-03-8
DESCRIPTION AND OPERATION
Output shaft
/'
Item Description
I 1 I Open cylinder roller bearing I
1 2 1 Output shaft with differential drive wheel I
1 3 1lst gear wheel I
1 4 1 1st gear double synchronisation I
151
Synchroniser - I stl2nd gear with reverse
gear
wheel
1 6 12nd gear double synchronisation I
Item Description
1 7 12nd gearwheel I
1 8 13rd gear wheel I
1 9 13rd gear simple synchronisation I
1 10 1 Synchroniser assembly - 3rdl4th gear I
11
12
2006.0 Fiesta 12/2006 G281365en
13 4th gear simple synchronisation
4th gear
wheel
Ball bearing (closed both
sides)
L
procarmanuals.com