mirror controls FORD FUSION HYBRID (AMERICAS) 2015 2.G Quick Reference Guide

Heated Front Seats*
To access, press the Climate corner on the touchscreen. For heated
front seats, press repeatedly to cycle through the various heat
modes and off. If your vehicle is not equipped with a touchscreen,
use the hard button controls (indicated by the same symbol) to
cycle through the various heat modes and off.
Memory Function*
Use the memory controls located on the driver’s door to program
and then recall memory positions. Move the seats and mirrors to
the desired positions. To program up to three positions, press and
hold the desired pre-set button until you hear a single tone. You
can now use these controls to recall the set positions.
Moonroof*
Your moonroof controls are
located on the overhead
console and have a one-touch
open and close feature.
To open the moonroof, press
the up arrow
. It stops short
of the fully opened position to
help reduce wind noise.
To close , press the down
arrow
.
To use the venting feature,
press the vent
button.
Tilting Head Restraints
Your vehicle’s front head restraints have
a tilting feature for extra comfort.
To Tilt the Head Restraint
Adjust the seatback to an upright driving
or riding position. Pivot the head restraint
forward toward your head to the desired
position. Once it is in the forward-most
position, tilting it forward once more
releases it to the upright position.
NOTE Do not attempt to force the head restraint backward after
it has been tilted. Instead, continue tilting it forward until the head
restraint releases to the upright position.
Ambient Lighting*
Lights various places, such as the footwells, with a choice of colors.
Access Using Your Touchscreen and Make Your Adjustments 1. Press the Settings icon > Vehicle > Ambient Lighting.
2. Touch the desired color.
3. Use the scroll bar to increase or decrease the intensity.
To switch off this feature, press the power button.
15
*if equipped
Intelligent Access*
NOTE Your intelligent access transmitter must be within
3 feet (1 meter) of the vehicle for intelligent access to
function properly.
This system operates the power locks. To unlock the driver’s door,
pull the front exterior door handle. To lock the doors, press the
sensor on top of the door handles. To unlock and open the trunk,
press the exterior trunk release button near the license plate. The
intelligent access transmitter also contains a mechanical key blade,
which can be used to unlock the driver’s door, if necessary. You must
have a valid transmitter inside the vehicle to switch on the ignition
and start the engine.
If you are unable to start your vehicle using the push button
start, do the following:
1. Place the transmitter in the backup slot inside the
center console.
2. With the transmitter in this position, press the brake pedal,
then the push button start to switch on the ignition and start
your vehicle. Remote Start*
Remote start allows you to start the engine from outside your
vehicle using your remote transmitter. To start, press and then
press twice within three seconds. Once inside, apply the brake
while pressing the START STOP button. Shift into drive (D) and go.
If you have the integrated keyhead transmitter, insert the key into
the ignition and switch on the ignition as you normally would before
driving. To switch off the engine from outside the vehicle after using
your remote start, press
once.
COMFORT
*if equipped

Rear View Camera
Provides a video image of the area behind the vehicle. The display
automatically appears in the touchscreen when the vehicle is in
reverse (R) and uses green, yellow and red guides to alert you of
your proximity to objects.
Front and Rear Sensing System*
Sounds a warning tone if there is an obstacle near either bumper.
The warning tone increases in frequency as the object gets closer.
The front sensors are active when the gearshift is in any position
other than park (P) or neutral (N) and the vehicle speed is below
6 mph (10 km/h). The rear sensors activate when the vehicle is in
reverse (R) and is traveling less than 3 mph (5 km/h).
Lane Keeping System*
Detects unintentional drifting out of your lane through
various driver alerts and steering corrections toward
the center of the lane. Set your system settings as
desired by Mode, Sensitivity and Intensity from your
information display screen.
Driver Alert*
Automatically monitors your driving behavior using various inputs
including the front camera sensor. If the system detects that your
driving alertness is reduced below a certain threshold, the system
alerts you by using a tone and displaying a message in the cluster
display. If no correction is made, warnings continue to alert the
driver. Press OK on the steering wheel to clear the warning.
Collision Warning System*
Designed to alert the driver of certain collision risks. A radar detects
if your vehicle is rapidly approaching another vehicle traveling in the
same direction as yours. If it is, a red warning light illuminates and
an audible warning tone sounds. If the risk of collision increases, the
system increases brake support to help reduce collision speed.
BLIS® (Blind Spot Information System)
with Cross Traffic Alert
*
BLIS aids you in detecting vehicles that may have entered into
your blind spot zone. Cross traffic alert warns you of vehicles
approaching from the sides when the transmission is in reverse (R).
BLIS and cross traffic turn on a yellow indicator light in the exterior
mirror on the side of the vehicle the approaching vehicle is coming
from. Refer to the Driving Aids chapter in your Owner’s Manual for
more information.
NOTE Visibility aids do not replace the need to watch where
the vehicle is moving. Refer to your Owner's Manual for safety
information, more details and system limitations.
*if equipped
FUNCTION
Configurable Daytime Running Lamps*
When you switch the feature on in the information display, daytime
running lamps turn on when you are driving, the lighting control is
in the autolamps position
and the headlamps are off. You can
switch the Configurable Daytime Running Lamps feature ON or OFF
using the information display controls. See the Lighting chapter in
your Owner’s Manual for complete information.
Electric Parking Brake
This feature replaces the conventional handbrake. The operating
switch is located on the center console, to the left of the
gearshift lever. To apply the electric parking brake, pull the switch up.
The brake system warning lamp lights to confirm that you applied
the electric parking brake.
You can release the electric parking brake manually by switching
the ignition on, pressing the brake pedal and then pressing the
electric parking brake switch. Refer to the Brakes chapter of
your Owner's Manual for more details.
Active Park Assist*
Detects an available parallel parking space and automatically
steers the vehicle into the space (hands-free) while you control
the accelerator, gearshift and brakes.
» Press the
button on the center console near the gearshift
lever. The touchscreen displays a message and a corresponding
graphic to indicate it is searching for a parking space.
» Use the direction indicator to indicate which side of the vehicle
you want the system to search. If the direction indicator is off,
the system automatically searches on the passenger side of
the vehicle.
» When the system locates a suitable space, the touchscreen
displays a message and a tone sounds. Slow down and stop
approximately even with the vehicle in front of where you wish
to park, then follow the instructions on the touchscreen.
NOTE The driver is always responsible for controlling the vehicle,
supervising the system and intervening, if required.
17
*if equipped