Torque FORD KUGA 2011 1.G Workshop Manual

34.
E68429
35.Refer to: Quick Release Coupling (310-00 Fuel
System - General Information, General
Procedures).
36. Torque: 12Nm•
• Torque: 24
Nm
2
37.Torque: 10Nm
E65220
38.Torque: 20Nm
E112607
1
2
34
39. N O T E : The gasket is to be reused unless
damaged.
E99980
40.
G1191241en2008.50 Kuga8/2011
303-01- 128
Engine— 2.5L Duratec (147kW/200PS) - VI5303-01-
128
INSTALLATION
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL
E68475
E116433
1

E112656
41.Torque: 25Nm1.
2. Torque: 5
Nm
G1191241en2008.50 Kuga8/2011
303-01- 129
Engine— 2.5L Duratec (147kW/200PS) - VI5303-01-
129
INSTALLATION
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL

E112652
43.Torque: 5Nm
E99948
G1191241en2008.50 Kuga8/2011
303-01- 131
Engine— 2.5L Duratec (147kW/200PS) - VI5303-01-
131
INSTALLATION
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL

49. CAUTION: Make sure that nocomponents catch.
General Equipment: Retaining Strap
General Equipment: Trolley Jack
E112303
15 mm
50.
E112649
Vehicles without PCM security shield
51.
E112653
52.Torque: 7Nm
E93509
G1191241en2008.50 Kuga8/2011
303-01- 134
Engine— 2.5L Duratec (147kW/200PS) - VI5303-01-
134
INSTALLATION
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL

Vehicles with PCM security shield
53.Torque: 7Nm
x4x4
E92343
All vehicles
54. CAUTION: Make sure that no
components catch.
Remove the following items:
• General Equipment: Retaining Strap
55. N O T E : Only tighten the bolts finger tight at this
stage. Remove the following items:
• General Equipment: Trolley Jack
E116626
56. CAUTION: Make sure that the inside of the pipe ends are clean and free of oil
residue.
1. Torque: 4Nm
2. Torque: 10Nm
E116646
1
2
2
G1191241en2008.50 Kuga8/2011
303-01- 135
Engine— 2.5L Duratec (147kW/200PS) - VI5303-01-
135
INSTALLATION
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL

57.
E65070
58.
E106249
59.
E112389
60.
E112311
61.To r q u e : 115Nm1.
2. Torque: 90
Nm
E68740
1
2
62.General Equipment: Hose Clamp
Remover/Installer
E112638
G1191241en2008.50 Kuga8/2011
303-01- 136
Engine— 2.5L Duratec (147kW/200PS) - VI5303-01-
136
INSTALLATION
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL

63.Torque: 10Nm
E112446
64.Torque: 12Nm
E101006
65.On both sides.
Torque: 35
x3
66.
G1191241en2008.50 Kuga8/2011
303-01- 137
Engine— 2.5L Duratec (147kW/200PS) - VI5303-01-
137
INSTALLATION
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL
Nm
E99147
E114689

8.Torque: 25Nm
E100040
x4
9.
E98184
10.
E98183
11 .Remove the cable ties securing the radiator and
condenser assembly.
G1062292en2008.50 Kuga8/2011
303-03- 9
Engine Cooling
303-03- 9
GENERAL PROCEDURES
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL

Coolant Pump — 2.5L Duratec (147kW/200PS) - VI5(24 404 0)
General EquipmentTrolley Jack
Removal
NOTE: Removal steps in this procedure may
contain installation details.
1. Drain the cooling system.
Refer to: Cooling System Draining and Vacuum
Filling (303-03 Engine Cooling, General
Procedures).
2. Remove the timing belt.
Refer to: Timing Belt (303-01 Engine - 2.5L
Duratec (147kW/200PS) - VI5, Removal and
Installation).
3. CAUTION: Use a wooden block to protect the oil pan when supporting the
engine.
Position the trolley jack with the wooden block
under the oil pan. Raise the trolley jack until the
front of the engine is free from load and the
coolant pump bolts can be accessed.
General Equipment: Trolley Jack
4. Torque: 17
Nm
E63823
x4
5.Lower the engine.
General Equipment: Trolley Jack 6.
Torque: 17
Nm
x3
E63856
Installation
1. NOTE: Install all the bolts finger tight before
final tightening.
To install, reverse the removal procedure.
G544632en2008.50 Kuga8/2011
303-03- 10
Engine Cooling
303-03- 10
REMOVAL AND INSTALLATION
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL

Cooling Fan Motor and Shroud — 2.5L Duratec (147kW/200PS)- VI5(24 222 0)
Removal
NOTE: Removal steps in this procedure may
contain installation details.
1. Refer to: Lifting(100-02 Jacking and Lifting,
Description and Operation).
2.
E98183
3.
E98184
4.
E112584
5.
E112335
6. Torque: 25Nm
G1156382en2008.50 Kuga8/2011
303-03- 11
Engine Cooling
303-03- 11
REMOVAL AND INSTALLATION
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL