lock FORD MUSTANG 1996 4.G Repair Manual

237
*
[SV01900( ALL)06/95]
q
If you must work with the engine running,
avoid wearing loose clothing or jewelry that
could get caught in moving parts. Take
appropriate precautions with long hair.
*
[SV02000( ALL)06/95]
q
Do not work on a vehicle in an enclosed
space with the engine running, unless you are
sure you have enough ventilation.
*
[SV02100( ALL)08/95]
q
Never get under a vehicle while it is
supported only by a jack. If you must work
under a vehicle, use safety stands.
*
[SV02200( ALL)06/95]
q
Keep all lit cigarettes and other smoking
materials away from the battery and all
fuel-related parts.
*
[SV02600(MBC )03/95]
If you disconnect the battery, the engine must
ªrelearnº its idle conditions before your vehicle
will drive properly. To find out how the engine
does this, seeBatteryin this chapter.
*
[SV02800( ALL)03/95]
Working with the engine off:
[SV02900(M )03/95]
1. Set the parking brake fully, block the wheels,
and make sure that the gearshift is securely
latched in P (Park) (automatic transmission)
or 1 (First) (manual transmission).
*
[SV03100( ALL)06/95]
2. Remove the key from the ignition after you
turn the engine off.
*
[SV03150( ALL)06/95]
3. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[SV03200( ALL)03/95]
Working with the engine on:
[SV03300(M )03/95]
1. Set the parking brake fully, and make sure
that the gearshift is securely latched in P
(Park) (automatic transmission) or Neutral
(manual transmission).
*
[SV03501( ALL)03/95]
2. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
File:15rcsvm.ex
Update:Thu Mar 28 14:48:54 1996

242 %
*
[SV05850( ALL)04/95]
Cleaning the Engine
*
[SV06000( ALL)04/95]
A clean engine is more efficient because a
buildup of grease and dirt acts as an insulator,
keeping the engine warmer than usual.
*
[SV06020( ALL)07/95]
q
Extreme care must be used if a power washer
is used to clean the engine. The high pressure
fluid could penetrate sealed parts and
assemblies causing damage or malfunctions.
*
[SV06040( ALL)08/95]
q
In order to avoid possible cracking of the
engine block or fuel injection pump, do not
spray a hot engine or injection pump with
cold water.
*
[SV06060( ALL)07/95]
q
The alternator, distributor and air intake must
be covered. Covering these components will
help prevent water damage.
*
[SV06080( ALL)04/95]
q
Never wash or rinse the engine while it is
running. Water getting into the engine may
cause internal damage.
%
*
[SV06100( ALL)03/95]
Filling the Fuel Tank
*
[SV06240(MBC )05/95]
The fuel door is outside the car on the passenger
side near the back. To fill the fuel tank:
*
[SV06550( ALL)05/95]
1. After opening the fuel filler door, remove
the cap carefully and slowly by turning it
counterclockwise 1/2 to 3/4 turn.
*
[SV06650( ALL)05/95]
RWARNING
The fuel system may be under pressure. If
the fuel cap is venting vapor or if you
hear a hissing sound while disengaging
the fuel cap, wait until it stops before
completely removing the cap. Otherwise,
fuel may spray out and injure you or
others.
File:15rcsvm.ex
Update:Thu Mar 28 14:48:54 1996

243
*
[SV06700( ALL)05/95]
2. Put the nozzle all the way inside the fuel
filler pipe before pumping the fuel.
*
[SV06800( ALL)09/95]
NOTE: If you spill any fuel on the body of
your vehicle, clean it off immediately.
The fuel may dull or soften the paint
if you do not wash it off.
%*
[SV06850( ALL)08/95]
3. Replace the fuel cap completely when you
are finished. Turn it clockwise 1/4 turn until
it is tight. It will click when it is fully
tightened.
*
[SV06875( ALL)10/95]
4. Push the fuel door closed.
[SV06900( ALL)05/95]
RWARNING
If you lose the fuel cap, replace it with a
Motorcraft or equivalent fuel cap. If you
do not use the proper fuel cap, the
pressure in the fuel tank can damage the
fuel system or cause it to work improperly
in a collision, endangering you and your
passengers.
*
[SV06950( ALL)09/95]
NOTE: If you replace your fuel cap with an
aftermarket fuel filler cap, the customer
warranty may be void for any damage
to the fuel tank and/or fuel system.
%*
[SV07500( ALL)06/95]
Choosing the Right Fuel
*
[SV07600( ALL)06/95]
Use only UNLEADED FUEL in your vehicle.
Using leaded fuel is prohibited by federal law.
Your warranty may not apply if your vehicle is
damaged because you used the wrong fuel.
*
[SV07701( ALL)05/95]
Using a high-quality fuel makes your vehicle
more responsive and maintain its good fuel
economy and emissions. It should not be
necessary to add any aftermarket products to
your fuel tank if you continue to use a
high-quality fuel.
File:15rcsvm.ex
Update:Thu Mar 28 14:48:54 1996

254 %
*
[SV18600( ALL)08/95]
Checking Hoses
*
[SV18700( ALL)11/94]
Inspect all engine and heater system hoses and
hose connections for deterioration, leaks, and
loose hose clamps as specified in theMaintenance
Schedule and Recordbooklet. Repair or replace
with Motorcraft hoses or equivalent as necessary.
*
[SV18800( ALL)09/95]
Adding Engine Coolant
*
[SV18900( ALL)09/95]
RWARNING
Do not put engine coolant in the container
for the windshield washer fluid.
*
[SV18950( ALL)09/95]
If sprayed to clean the glass, engine coolant or
antifreeze could make it difficult to see through
the windshield.
[SV19000(MBC )05/95]
RWARNING
Never remove the radiator cap or vent
plug while the engine is running or hot.
[SV19030( ALL)05/95]
Follow these steps to avoid personal injury that
can be caused by escaping steam or engine
coolant.
[SV19040(MBC )03/95]
1. Before you remove the cap, turn the engine
off and let it cool. Even when the engine is
cool, be careful when you remove the
radiator cap or vent plug.
[SV19145( ALL)03/95]
2. When the engine is cool, wrap a thick towel
around the cap and turn it slowly
counterclockwise to unscrew.
*
[SV19150( ALL)09/95]
3. Step back while the pressure releases.
[SV19160( ALL)12/94]
4. When you are sure that all the pressure has
been released, use the cloth to press the cap
down, turn it, and remove it.
File:15rcsvm.ex
Update:Thu Mar 28 14:48:54 1996

258 [SV21200(MBC )03/93]q
Start and idle engine until the radiator upper
hose is warm (this indicates the thermostat is
open and coolant is flowing through the
entire system).
[SV21300(MBC )03/93]
q
Immediately shut off engine. Cover cap
completely with a thick cloth and cautiously
remove radiator pressure cap and add a
50/50 mixture of recommended coolant and
water until system is full.
[SV21400(MBC )03/91]
q
Reinstall the radiator cap securely.
[SV21500(MBC )05/94]
q
Remove the cap from the engine coolant
recovery reservoir and add a 50/50 mixture
of recommended cooling system fluid and
water to the FULL-HOT mark on the engine
coolant recovery reservoir. Check that
reservoir hose is not kinked.
[SV21800(MBC )03/93]
q
Reinstall the reservoir cap.
*
[SV21900(MBC )05/95]
q
Check for leaks at the draincock, block plug
and vent plug.
*
[SV22000(MBC )03/95]
q
Recheck the engine coolant level, using the
recommended procedure, after one or two
occasions of vehicle use.
[SV22012(M )05/95]
4.6L (2V) engine only Ð GT models
*
[SV22014( ALL)03/95]
q
With the engine OFF and cool, remove the
pressure cap, located on the coolant reservoir.
Remove the heater hose and clamp, located
on the rear of the intake manifold.
*
[SV22021( ALL)03/95]
q
Add a 50/50 mixture of specified coolant and
water to the coolant reservoir. Refer toRefill
Capacitieslater in this chapter for the correct
amount. Add coolant to the reservoir until
the coolant continuously flows out of the tube
in the rear of engine. Reattach hose and
secure clamp.
File:15rcsvm.ex
Update:Thu Mar 28 14:48:54 1996

291 [SV46710(M )05/95]
quarter page art:0011232-B
Headlamp access covers
[SV46875(M )08/93]
3. Lift the cover and find the bulb in the
headlamp socket.
[SV47125(M )06/93]
4. Remove the electrical connector from the
bulb by lifting the connector clip upward
while pulling the connector rearward.
[SV47250(M )08/93]
5. Remove the retaining ring by turning
counterclockwise 1/8 of a turn to free it
from the socket. Then slide the ring off the
plastic base.Keep the ring.You must use it
again to hold the new bulb in place.
[SV47300(M )11/92]
6. Carefully remove the bulb assembly from its
socket by gently pulling it rearward without
turning.
File:15rcsvm.ex
Update:Thu Mar 28 14:48:54 1996

292
*
[SV47400( ALL)03/95]
Installing the headlamp bulb
*
[SV47600(MBC )02/95]
1. With the flat side of the bulb's plastic base
facing upward, insert the glass end of the
bulb into the socket. You may need to turn
the bulb left or right to line up the grooves
in the plastic base with the tabs in the
socket. When the grooves are aligned, push
the bulb into the socket until the plastic base
contacts the rear of the socket.
*
[SV47800(MBC )08/95]
2. Slip the bulb retaining ring over the plastic
base until it contacts the rear of the socket.
Lock the ring into the socket by rotating it
clockwise until you feel a ªstop.º
*
[SV47900( ALL)02/95]
3. Push the electrical connector into the rear of
the plastic base until it snaps, locking it into
position.
*
[SV48000(MBC )02/95]
4. Turn the headlamps on and make sure that
they work properly. If the headlamp was
correctly aligned before you changed the
bulb, you should not need to align it again.
[SV48075(M )05/95]
5. Reinstall the headlamp cover pushpin and
tighten until snug.
File:15rcsvm.ex
Update:Thu Mar 28 14:48:54 1996

Index 317
Index
A
ABS warning light
(see Anti-lock brake system)....... 65
Accessory position on the ignition..... 49
Accessory power source,
power point outlet.......... 130
Additives, engine oil.......... 249
Air bag supplemental restraint system
and child safety seats........ 24,30
description............... 22
disposal................ 28
driver air bag........... 22,25
indicator light............. 67
operation............... 25
passenger air bag............ 25
proper seating............. 23
service and information labels...... 25
tone generator............. 28
wearing safety belts........... 22
Air cleaner filter
location............... 239
specifications............. 299
Air conditioning, manual heating and air
conditioning system........... 80
Alarm, activating remote personal.... 111
Alcohol, in fuel............. 244
Antenna, radio (see Electronic
sound system)..........141, 173
Antifreeze (see Engine coolant)...... 252
Anti-lock brake system (ABS)
description.............. 186
see also Brake............ 186
warning light.............. 65
File:rcixm.ex
Update:Wed Mar 27 09:41:15 1996

Index 319
Battery (continued)
servicing............... 259
voltage gauge............. 76
when storing your vehicle....... 303
Brake fluid
brake warning light........... 64
checking and adding......... 272
description.............. 272
specifications............. 300
Brakelamp, bulb replacement....... 292
Brakes
adjustment.............. 186
anti-lock............... 186
anti-lock brake system (ABS)
warning light............ 65
applying the brakes.......... 186
brake warning light........... 64
fluid, checking and adding...... 272
fluid, refill capacities.......272, 298
fluid, specifications.......... 300
front disc.............. 186
if brakes do not grip well....... 186
master cylinder............ 272
new brake linings............ 5
noise..............186±187
parking............... 188
power braking............ 186
servicing............... 272
stopping distances.......... 190
trailer................ 196
when storing your vehicle....... 303
Brake-shift interlock........... 178
Break-in period.............. 5
Brights (high beams)........... 70
Bulbs
replacing............... 288
halogen............... 289
headlamps.............. 289
specifications............. 292
File:rcixm.ex
Update:Wed Mar 27 09:41:15 1996

320 Index
C
Canada, customer assistance....... 223
Canada, warranty information....... 4
Canadian Motor Vehicle Arbitration Plan
(CAMVAP).............. 223
Capacities for refilling fluids....... 298
Carbon monoxide in exhaust........ 56
Car seats for children
(see Child safety seats)......... 30
Cassette tape player (see Electronic
sound system)......141, 145, 162, 168
Catalytic converter............ 293
CD player (see Electronic
sound system)........148, 154, 155
Chains, tires.............. 268
Changing a tire............. 205
Charging system gauge.......... 76
Charging system warning light....... 68
Child safety restraints........... 28
child safety belts............ 46
child safety seats............ 30
Child safety seats
and air bags............ 24,30
automatic locking mode
(retractor)....... 14,15,30,32,39
in front seat............ 24,30
in front seat, convertible......... 32
in front seat, coupe........... 39
in rear outboard seat........ 30,39
in rear seat............... 30
Chime
key in ignition............. 51
safety belt............... 66
Circuit breakers
checking and replacing........ 287
see also fuses............. 278
Cleaning your vehicle
CD player and discs........152, 159
chrome and aluminum parts....... 7
File:rcixm.ex
Update:Wed Mar 27 09:41:15 1996