engine coolant FORD MUSTANG 1997 4.G User Guide
[x] Cancel search | Manufacturer: FORD, Model Year: 1997, Model line: MUSTANG, Model: FORD MUSTANG 1997 4.GPages: 321, PDF Size: 2.81 MB
Page 226 of 321
![FORD MUSTANG 1997 4.G User Guide 228
*
[MC14905( ALL)05/96]
Coolant refill capacity
[MC14910( ALL)05/96]
To find out how much fluid your vehicles
cooling system can hold, refer toRefill Capacities
in theCapacities and Specifications FORD MUSTANG 1997 4.G User Guide 228
*
[MC14905( ALL)05/96]
Coolant refill capacity
[MC14910( ALL)05/96]
To find out how much fluid your vehicles
cooling system can hold, refer toRefill Capacities
in theCapacities and Specifications](/img/11/5204/w960_5204-225.png)
228
*
[MC14905( ALL)05/96]
Coolant refill capacity
[MC14910( ALL)05/96]
To find out how much fluid your vehicle's
cooling system can hold, refer toRefill Capacities
in theCapacities and Specificationschapter.
*
[MC14915( ALL)05/96]
Have your dealer check the engine cooling
system for leaks if you have to add more than a
quart (liter) of engine coolant per month.
*
[MC15005( ALL)05/96]
Severe winter climate
*
[MC15105( ALL)05/96]
If you drive in extremely cold climates (less than
-34ÊF [-36ÊC]), it may benecessary to increase
the coolant concentration above 50%. Refer to
the chart on the coolant container to ensure the
coolant concentration in your vehicle is such that
the coolant will not freeze at the temperature
level in which you drive during winter months.
Never increase the engine coolant concentration
above 60%. Leave a 50/50 mixture of engine
coolant and water in your vehicle year-round in
non-extreme climates.
%*
[MC15200( ALL)05/96]
Engine Coolant Drain and Flush
[MC15300( ALL)04/96]
Proper procedures for a complete coolant drain
and flush of the cooling system can be found in
theCar Service Manual. Following these
recommended procedures will ensure that the
specified coolant level and a 50/50 or
appropriate mixture of coolant and water is
maintained.
*
[MC15400( ALL)12/95]
Engine Coolant Refill Procedure
*
[MC15500( ALL)12/95]
When the entire cooling system is drained and
refilled, the following procedure should be used
to ensure a complete fill:
*
[MC15600( ALL)12/95]
NOTE: It is imperative the following
procedure be adhered to. Failure to do
so could result in damage to your
engine.
File:11rcmcm.ex
Update:Thu Apr 3 07:49:33 1997
Page 227 of 321
![FORD MUSTANG 1997 4.G User Guide 229 [MC15700(MBC )12/95]
3.8L engine only
[MC15800(MBC )12/95]
q
Open the vent plug.
[MC15900(MBC )12/95]
q
Remove coolant recovery reservoir cap.
[MC16000(MBC )12/95]
q
Remove radiator pressure cap.
FORD MUSTANG 1997 4.G User Guide 229 [MC15700(MBC )12/95]
3.8L engine only
[MC15800(MBC )12/95]
q
Open the vent plug.
[MC15900(MBC )12/95]
q
Remove coolant recovery reservoir cap.
[MC16000(MBC )12/95]
q
Remove radiator pressure cap.](/img/11/5204/w960_5204-226.png)
229 [MC15700(MBC )12/95]
3.8L engine only
[MC15800(MBC )12/95]
q
Open the vent plug.
[MC15900(MBC )12/95]
q
Remove coolant recovery reservoir cap.
[MC16000(MBC )12/95]
q
Remove radiator pressure cap.
[MC16100(MBC )12/95]
q
With the engine off and cool, add a 50/50
mixture of recommended cooling system fluid
and water to the radiator until full, then add
to the reservoir until the reservoir is at the
FULL-HOT level.
[MC16200(MBC )12/95]
q
Close the vent plug.
[MC16300(MBC )12/95]
q
Reinstall the coolant recovery reservoir cap
by installing the cap to the fully installed
position.
[MC16400(MBC )12/95]
q
Reinstall the pressure cap to the pressure
relief position by installing the cap to the
fully installed position, and then backing off
to the first stop.
[MC16500(MBC )12/95]
q
Start and idle engine until the radiator upper
hose is warm (this indicates the thermostat is
open and coolant is flowing through the
entire system).
[MC16600(MBC )12/95]
q
Immediately shut off engine. Cover cap
completely with a thick cloth and cautiously
remove radiator pressure cap and add a
50/50 mixture of recommended coolant and
water until system is full.
[MC16700(MBC )12/95]
q
Reinstall the radiator cap securely.
[MC16800(MBC )12/95]
q
Remove the cap from the engine coolant
recovery reservoir and add a 50/50 mixture
of recommended cooling system fluid and
water to the FULL-HOT mark on the engine
coolant recovery reservoir. Check that
reservoir hose is not kinked.
[MC16900(MBC )12/95]
q
Reinstall the reservoir cap.
File:11rcmcm.ex
Update:Thu Apr 3 07:49:33 1997
Page 228 of 321
![FORD MUSTANG 1997 4.G User Guide 230
*
[MC17000(MBC )12/95]
q
Check for leaks at the draincock, block plug
and vent plug.
*
[MC17100(MBC )12/95]
q
Recheck the engine coolant level, using the
recommended procedure, after one or two
oc FORD MUSTANG 1997 4.G User Guide 230
*
[MC17000(MBC )12/95]
q
Check for leaks at the draincock, block plug
and vent plug.
*
[MC17100(MBC )12/95]
q
Recheck the engine coolant level, using the
recommended procedure, after one or two
oc](/img/11/5204/w960_5204-227.png)
230
*
[MC17000(MBC )12/95]
q
Check for leaks at the draincock, block plug
and vent plug.
*
[MC17100(MBC )12/95]
q
Recheck the engine coolant level, using the
recommended procedure, after one or two
occasions of vehicle use.
[MC17300(M )12/95]
4.6L (2V) engine only Ð GT models
*
[MC17400( ALL)12/95]
q
With the engine OFF and cool, remove the
pressure cap, located on the coolant reservoir.
Remove the heater hose and clamp, located
on the rear of the intake manifold.
*
[MC17500( ALL)12/95]
q
Add a 50/50 mixture of specified coolant and
water to the coolant reservoir. Refer toRefill
Capacitieslater in this chapter for the correct
amount. Add coolant to the reservoir until
the coolant continuously flows out of the tube
in the rear of engine. Reattach hose and
secure clamp.
[MC17600( ALL)12/95]
q
Continue to fill the reservoir until the coolant
is at the FULL COLD level.
*
[MC17700( ALL)12/95]
q
Reinstall the pressure cap to the fully
installed position.
*
[MC17800( ALL)12/95]
q
Start and idle the engine until the radiator
upper hose is warm (this indicates the
thermostat is open and coolant is flowing
through the entire system).
*
[MC17900( ALL)12/95]
q
Immediately shut off the engine and let cool.
Cautiously remove the pressure relief cap and
add a 50/50 mixture of specified coolant and
water until the coolant is at the COLD FILL
level in the coolant reservoir.
File:11rcmcm.ex
Update:Thu Apr 3 07:49:33 1997
Page 229 of 321
![FORD MUSTANG 1997 4.G User Guide 231
*
[MC18000( ALL)12/95]
q
Reinstall the pressure cap securely.
*
[MC18100( ALL)12/95]
q
Check for leaks at the draincock.
*
[MC18200( ALL)12/95]
q
Recheck the engine coolant level, using the
recomm FORD MUSTANG 1997 4.G User Guide 231
*
[MC18000( ALL)12/95]
q
Reinstall the pressure cap securely.
*
[MC18100( ALL)12/95]
q
Check for leaks at the draincock.
*
[MC18200( ALL)12/95]
q
Recheck the engine coolant level, using the
recomm](/img/11/5204/w960_5204-228.png)
231
*
[MC18000( ALL)12/95]
q
Reinstall the pressure cap securely.
*
[MC18100( ALL)12/95]
q
Check for leaks at the draincock.
*
[MC18200( ALL)12/95]
q
Recheck the engine coolant level, using the
recommended procedure, after one or two
occasions of vehicle use.
%
*
[MC18300( ALL)01/96]
Power Steering Fluid
*
[MC18400( ALL)01/96]
Check the level of the power steering fluid at
least twice a year (i.e., every Spring and Fall).
%*
[MC18500( ALL)01/96]
Checking and Adding Power Steering
Fluid
[MC18650(M )04/96]
3.8L SFI engine (check warm)
*
[MC18700( ALL)04/96]
1. Start the engine and let it run until the
power steering fluid reaches normal
operating temperature. The power steering
fluid will be at the right temperature when
the engine coolant temperature gauge in the
instrument cluster is near the center of the
NORMAL operating temperature range.
*
[MC18800( ALL)01/96]
2. While the engine idles, turn the steering
wheel back and forth several times. Make
sure that the cap assembly is installed at this
time.
*
[MC18900( ALL)01/96]
3. Turn the engine off.
%*
[MC19000(MBC )01/96]
4. Check the fluid level on the dipstick (which
is highlighted in yellow in your vehicle). The
fluid level should be between the arrows in
the FULL HOT range, which is marked on
the side of the dipstick, opposite the side
marked FULL COLD. Do not add fluid if the
level is within the FULL HOT range.
*
[MC19200(MBC )01/96]
5. If the power steering fluid is low, add fluid
in small amounts, continuously checking the
level, until you reach the FULL HOT range.
Do not overfill.
File:11rcmcm.ex
Update:Thu Apr 3 07:49:33 1997
Page 298 of 321

Index 309
Index
A
ABS warning light
(see Anti-lock brake system)....... 12
Accessories............... 287
Accessory position on the ignition..... 65
Accessory power source, power
point outlet.............. 63
Additives, engine oil.......... 216
Air bag supplemental
restraint system..........124, 129
and child safety seats.......129±130
description............124±125
driver air bag..........124±125
indicator light............. 14
operation.............. 125
passenger air bag........... 125
service and information labels..... 125
tone generator............ 127
Air cleaner filter
location............... 213
specifications............. 265
Air conditioning, manual heating and air
conditioning system........... 55
Alarm, activating remote personal..... 98
Antenna, radio
(see Electronic sound system)...... 25
Antifreeze (see Engine coolant)...... 224
Anti-lock brake system (ABS)
description.............. 157
see also Brake............ 157
warning light.............. 12
warninig light............. 11
Anti-theft lug nuts and key....... 199
File:rcixm.ex
Update:Thu Apr 3 07:52:02 1997
Page 303 of 321

314 Index
Cold engine starting........... 151
Combination lap and shoulder belts . . 111, 114
Compact disc player (see Electronic sound
system)................. 34
Console, description............ 83
Controls, mirrors............. 77
Convenience kit in cargo area...... 193
Convertible
cleaning................ 91
installation of the boot.......... 87
lowering the convertible top....... 85
raising the convertible top........ 90
Coolant (see Engine coolant)....... 224
checking and adding......... 224
drain and flush............ 228
preparing for storage......... 270
refill capacities............ 266
specifications............. 267
temperature gauge........... 18
warnings............... 224
Cooling fan............... 210
Crankcase emission filter......... 265
Customer Assistance Center, Ford (U.S.) . . 277
Customer Assistance Centre,
Ford of Canada..........277, 283
D
Daytime running light system....... 59
Defrost
rear window.............. 58
windshield............... 57
Dipstick................ 217
automatic transmission fluid....234, 236
engine oil.............. 217
power steering fluid.......... 231
Disabled vehicle (see Towing)...... 207
Dispute Settlement Board........ 278
File:rcixm.ex
Update:Thu Apr 3 07:52:02 1997
Page 305 of 321

316 Index
Engine
check engine warning light....... 17
does not start...........152, 190
fuel injected engine, starting....149±150
fuel pump shut-off switch....... 190
preparing to start........... 149
refill capacities............ 266
service points............. 213
starting................ 150
starting after a collision........ 190
storing your vehicle........268±269
Engine block heater........... 153
Engine coolant............. 224
checking and adding......... 224
checking hoses............ 226
disposal...........210, 219, 236
drain and flush............ 228
low coolant warning light........ 14
preparing for storage......... 270
proper solution........210, 219, 236
recovery reservoir.........213, 224
refill capacities............ 266
specifications............. 267
temperature gauge........... 18
Engine coolant temperature gauge..... 18
description............... 18
mechanical.............18±19
Engine coolant temperature
guage:electronic............. 18
Engine fan............... 210
Engine oil............... 216
changing oil and oil filter.....217, 219
checking and adding......... 217
dipstick............... 217
disposal...........210, 219, 236
engine oil pressure gauge........ 22
filter, specifications.......... 265
refill capacities............ 266
specifications...........216, 267
synthetic oil............. 216
File:rcixm.ex
Update:Thu Apr 3 07:52:02 1997
Page 307 of 321

318 Index
Fuel cap................ 246
removing............... 246
replacing............... 246
Fuel filler door............. 246
remote release............ 246
Fuel filter, specifications......... 265
Fuel gauge................ 18
Fuel pump shut-off switch
engine does not start......... 190
starting after a collision........ 190
Fuse panels
engine compartment.......... 185
high current fuse panel........ 186
instrument panel.........181, 188
Fuses
charts..............183, 188
checking and replacing........ 188
circuit breakers............ 189
G
Gas cap (see Fuel cap).......... 246
Gas mileage (see Fuel economy)..... 247
Gasoline (see Fuel)............ 246
Gauges, Electronic
engine coolant temperature gauge.... 18
fuel gauge............... 18
odometer................ 20
speedometer.............. 20
Gauges, Mechanical
engine coolant temperature gauge.... 18
engine oil pressure gauge........ 22
fuel gauge............... 18
odometer................ 20
speedometer.............. 20
tachometer............... 21
trip odometer.............. 20
File:rcixm.ex
Update:Thu Apr 3 07:52:02 1997
Page 311 of 321

322 Index
Lights, warning and indicator (continued)
engine oil pressure........... 22
hazard warning light.......... 71
high beam............... 16
low coolant............... 14
oil pressure............... 22
overdrive off.............. 15
safety belt............... 13
service engine soon........... 17
turn signal indicator....... 17,67±68
Load limits............... 170
GAWR................ 170
GVWR................ 170
trailer towing............. 173
Lubricant specifications......... 267
Lug nuts................ 194
anti-theft............... 199
standard............... 195
tightening sequence........194, 198
M
Maintenance schedule and record
(see separate Maintenance Schedule and
Record booklet)............. 4
Maintenance (see Servicing)....... 209
Maintenance (see servicing)........ 209
Manual transaxle
backing up (reverse).......... 168
clutch................ 167
shifting gears............. 168
shift speeds.............. 169
Manual transmission
backing up (reverse).......... 168
clutch..............167, 222
driving................ 167
fluid, checking and adding....... 237
fluid capacities............ 266
lubricant specifications......... 267
shifting gears............. 168
shift speeds.............. 169
File:rcixm.ex
Update:Thu Apr 3 07:52:02 1997