coolant reservoir FORD MUSTANG 2000 4.G User Guide

9. Check the coolant level in the reservoir before
you drive your vehicle the next few times (with the
engine cool).
10. If necessary, add a50/50 mixtureof engine
coolant and distilled water to the engine coolant
reservoir until the coolant level is at the ªcold fill
levelº as listed on the reservoir.
Recycled engine coolant
Ford Motor Company recommends the use of a
recycled engine coolant produced by Ford-approved
processes.
Not all coolant recycling processes produce coolant
which meets Ford specification ESE-M97B44-A. Use
of a recycled engine coolant which does not meet
the Ford specification may harm engine and cooling
system components.
Always dispose of used automotive fluids in a
responsible manner. Follow your community's
regulations and standards for recycling and disposing
of automotive fluids.
Coolant refill capacity
To find out how much fluid your vehicle's cooling
system can hold, refer toRefill capacitiesin the
Capacities and specificationschapter.
Fill your engine coolant reservoir as outlined in
Adding engine coolantin this chapter.
Severe climates
If you drive in extremely cold climates (less than
±36É C [±34É F]):
²it may be necessary to increase the coolant
concentration above 50%.
²NEVER increase the coolant concentration
above 60%.
²increased engine coolant concentrations
above 60% will decrease the overheat
Maintenance and care
150

If your vehicle is
equipped with the
3.8L V6 engine,check
the power steering
fluid level with the
engine at normal
operating temperature.
1. Start the engine and
let it run until it
reaches normal
operating temperature
(the engine coolant
temperature gauge
indicator will be near
the center of the
normal area between H
and C).
2. While the engine idles, turn the steering wheel
left and right several times.
3. Turn the engine off.
4. Check the fluid level on the dipstick. It should be
within the FULL HOT range. Do not add fluid if the
level is within this range.
5. If the fluid is low, add fluid in small amounts,
continuously checking the level until it reaches the
correct operating range. Be sure to put the cap back
on the reservoir.
FILL
HOT
Maintenance and care
152

MOTORCRAFT PART NUMBERS
Component 3.8L OHV V6 engine 4.6L SOHC V8 engine
Air filter element FA-1611 FA-1634
Fuel filter FG-800AFG-986 FG-800AFG-986
Battery BXT-59 BXT-59
Oil filter FL-400S FL-820S
PCV valve EV-152 EV-98
Spark plugs* AWSF-42EE** AWSF-32P
* Refer to Vehicle Emissions Control Information (VECI) decal for
spark plug gap information.
**If a spark plug is removed for inspection, it must be reinstalled in
the same cylinder. If a spark plug needs to be replaced, use only spark
plugs with the same service part number suffix letter as shown on the
engine decal.
REFILL CAPACITIES
Fluid Ford Part Name Application Capacity
Brake fluid High Performance
DOT 3 Motor
Vehicle Brake
FluidAll Fill to line on
reservoir
Engine oil
(includes filter
change)Motorcraft SAE
5W-30 Super
Premium Motor
OilAll 4.7L (5.0 quarts)
Engine coolant
1Premium Engine
Coolant3.8L OHV V6
engine11.2L
(11.8 quarts)
4.6L SOHC V8
engine13.3L
(14.1 quarts)
Power steering
fluidMotorcraft
MERCONtAT F3.8L OHV V6
engineKeep in FULL
HOT range on
dispstick
4.6L SOHC V8
engineFill to between
MIN and MAX
lines on reservoir
Rear axle
lubricant
2Motorcraft SAE
80W-90 Premium
Rear Axle
Lubricant7.5 inch axle 1.5L (3.25 pints)
8.8 inch axle 1.7L (3.75 pints)
Fuel tank N/A All 59.4L
(15.7 gallons)
Capacities and specifications
191

Item Information
Required fuel Unleaded fuel only - 87 octane
Fuel tank capacity 59.4L (15.7 gallons)
Engine oil capacity
(includes filter
change)4.7L (5.0 quarts). Use Motorcraft SAE
5W-30 Super Premium Motor Oil,
Ford specification WSS-M2C153-G
Tire size and
pressureSee label on inside of glove box door.
Hood release Pull handle under the left side of the
instrument panel.
Coolant
capacity-3.8L OHV
V6 engine
1
11.2L (11.8 quarts)
Coolant capacity-
4.6L SOHC V8
engine
1
13.3L (14.1 quarts)
Power steering fluid
capacityFill to line on reservoir or dipstick.
Use Motorcraft MERCONtAT F.
Manual transmission
fluid capacity-3.8L
OHV V6 engine
2
2.6L (5.6 pints). Use Motorcraft
MERCONtAT F.3
Manual transmission
fluid capacity-4.6L
SOHC V8 engine
2
3.1L (6.6 pints). Use Motorcraft
MERCONtAT F.3
Automatic
transmission fluid
capacity-3.8L OHV
V6 engine
2
13.1L (13.9 quarts). Use Motorcraft
MERCONtV ATF.4
Automatic
transmission fluid
capacity-4.6L SOHC
V8 engine
2
12.0L (12.8 quarts). Use Motorcraft
MERCONtV ATF.4
Windshield washer
fluid3.8L (4.0 quarts). Use Ultra-Clear
Windshield Washer Concentrate.
1Use Ford Premium Engine Coolant (green in color). DO NOT USE
Ford Extended Life Engine Coolant (orange in color). Refer to
Adding engine coolant, in the Maintenance and Care chapter.
2Ensure the correct automatic transmission fluid is used.
Transmission fluid requirements are indicated on the dipstick or on
the dipstick handle. MERCONtand MERCONtV are not
interchangeable. DO NOT mix MERCONtand MERCONtV. Refer to
your Scheduled Maintenance Guide to determine the correct service
interval.
Filling station information
223