oil change FORD MUSTANG 2008 5.G Shelby GT500 Supplement Manual

Introduction
2
Shelby GT500 unique features
4
Driving your Shelby GT500
8
Alternate calibration 8
Transmission operation 8
Driving through water 9
Ground clearance 9
Washing your vehicle 10
Chassis
11
Lug nut torque 12
Roadside Emergencies
16
Temporary mobility kit 16
Fuses and relays 24
Wrecker towing 25
Maintenance and Specifications
29
Engine oil 30
Air filter(s) 34
Part numbers 35
Refill capacities 36
A word about warranty coverage
40
All rights reserved. Reproduction by any means, electronic or mechanical
including photocopying, recording or by any information storage and retrieval
system or translation in whole or part is not permitted without written
authorization from Ford Motor Company. Ford may change the contents without
notice and without incurring obligation.
Copyright © 2007 Ford Motor Company
Table of Contents
1
2008 05+ Mustang(197)
Supplement
USA(fus)

ENGINE OIL RECOMMENDATION
Use Motorcraft SAE 5W-50 full synthetic or an equivalent SAE 5W-50 full
synthetic oil meeting Ford specification WSS-M2C931-B.
Do not use supplemental engine oil additives, cleaners or other engine
treatments. They are unnecessary and could lead to engine damage that
is not covered by Ford warranty.
Change your engine oil and filter according to the appropriate schedule
listed in the Scheduled Maintenance Guide.
ENGINE AND INTERCOOLER COOLANT
The concentration and level of engine coolant should be checked at the
mileage intervals listed in the scheduled maintenance guide. The coolant
concentration should be maintained at 50/50 coolant and water, which
equates to a freeze point of -36°C (-34°F). Coolant concentration testing
is possible with a hydrometer or antifreeze tester (such as the Rotunda
Battery and Antifreeze Tester, 0014–R1060). The level of coolant should
be maintained at the “cold fill range” level in the coolant reservoir. If the
level falls below, add coolant per the instructions in theAdding Engine
Coolantsection.
Your vehicle was factory-filled with a 50/50 engine coolant and water
concentration. If the concentration of coolant falls below 40% or above
60%, the engine parts could become damaged or not work properly.
A 50/50 mixture of coolant and water provides the following:
•freeze protection down to -36°C (-34°F).
•boiling protection up to 129°C (265°F).
•protection against rust and other forms of corrosion.
•an accurate temperature readout from the engine coolant
gauge.
2008 05+ Mustang(197)
Supplement
USA(fus)
Maintenance and Specifications
30

REFILL CAPACITIES
Fluid Ford Part Name Capacity
Brake fluidMotorcraft High
Performance DOT 3
Motor Vehicle Brake
FluidBetween MIN and
MAX lines on reservoir
Engine oil (includes
filter change)Motorcraft 5W-50 Full
Synthetic Motor Oil6.5 quarts (6.1L)
Engine coolant
1
Motorcraft Premium
Engine Coolant
(green-colored) or
Motorcraft Premium
Gold Engine Coolant
(yellow-colored)21.1 quarts (20.0L)
Intercooler coolant
1
Motorcraft Premium
Engine Coolant
(green-colored) or
Motorcraft Premium
Gold Engine Coolant
(yellow-colored)3.96 quarts (3.75L)
(See your authorized
dealer for service)
Power steering fluidMotorcraft
MERCON
VATFBetween MIN and
MAX lines on reservoir
Rear axle lubricant
2
Motorcraft SAE
75W-140 High
Performance Synthetic
Rear Axle Lubricant4.25 pints (2.0L)
Fuel tank — 15.7 gallons (59.4L)
Transmission fluid
3MERCON
V ATF 6.35 pints (3.5L)4
Windshield washer
fluidUltra-Clear Windshield
Washer Concentrate4.0 quarts (3.8L)
1Add the coolant type originally equipped in your vehicle.2Rear axle lubricants do not need to be checked or changed unless a
leak is suspected, service is required or the axle assembly has been
submerged in water. The axle lubricant should be changed any time the
rear axle has been submerged in water, using SAE 75W-140 High
Performance rear axle lube, meeting Ford specification WSP-M2C102–A.
2008 05+ Mustang(197)
Supplement
USA(fus)
Maintenance and Specifications
36