jump cable FORD MUSTANG MACH E 2023 Owners Manual

The service is available 24 hours a day,seven days a week.
This program is separate from the NewVehicle Limited Warranty, but the coverageis concurrent with the powertrain coverageperiod of your vehicle. Canadian roadsidecoverage and benefits may differ from theU.S. coverage.
If you require more information, please callus in Canada at 1-800-665-2006, or visitour website at www.ford.ca.
SWITCHING THE HAZARD
FLASHERS ON AND OFF
The hazard flashers operate with thepower on or off. The battery loses chargeand may have insufficient power to restartyour vehicle.
The hazard flasher button is onthe center console. Press thebutton to turn on the hazardflashers if your vehicle is creating a safetyhazard for other road users.
When you switch the hazard flashers on,all front and rear direction indicators flash.
Press the button again to switch them off.
JUMP STARTING THE VEHICLE
JUMP STARTING PRECAUTIONS
WARNING: Connect batteries withonly the same nominal voltage.
WARNING: Use only adequatelysized cables with insulated clamps.
Note:This procedure is only for the 12 voltunder hood battery.
Note:Your vehicle has a 12 volt battery thatis easily accessible under the hood. The 12volt battery controls the switches andcontacts that engage the high voltagebattery. Do not jump start the high voltagebattery using a standard 12 volt battery. Towyour vehicle to an authorized dealer if thehigh voltage battery does not accept aregular charge.
Note:Do not attempt to push start yourvehicle. You could cause transmissiondamage.
Note:Do not disconnect the 12 volt batteryfrom your vehicle electrical system.
PREPARING THE VEHICLE
Opening the Front LuggageCompartment With No VehiclePower
If the vehicle has no power, you will beunable to open the front luggagecompartment. To open the front luggagecompartment follow the steps below:
1.Use an external power supply such asa 12 volt jump box.
2.Remove the cover at the front of yourvehicle below the headlight. Pressfirmly on the top right of the coversedge, then pull the raised section onthe bottom left toward you.
307
2023 Mustang Mach-E (CGW) Canada/United States of America, enUSA, Edition date: 202209, DOMCrash and Breakdown InformationE75790 E323341

3.Pull both wires out of the opening toreveal both terminals.
4.Connect the external power supply tothe terminals
Note:Be sure to match the red positivecable (A) to the red positive terminal andthe black negative cable (B) to the blacknegative terminal.
5.Turn on the external power supply.
Note:Refer to the manufacturer'sinstructions for external power supply use.
Note:If performed correctly, the frontluggage compartment latches immediatelyrelease, and you have access to the frontluggage compartment.
6.Disconnect the external power supplywhen it is no longer required.
7.To reinstall the cover, reverse theremoval procedure.
To Connect the Booster Cables
WARNING: Do not connect thenegative jumper cable to any other partof your vehicle. Use the ground point.
To access the booster cable connectionpoints, remove the rear and left side frontluggage compartment covers. SeeInstalling and Removing the LuggageCompartment Cover (page 297).
Note:Make sure that the cables are clearof any moving parts.
308
2023 Mustang Mach-E (CGW) Canada/United States of America, enUSA, Edition date: 202209, DOMCrash and Breakdown InformationABE323342 E338543E338543A1234..

1.Connect the positive (+) jumper cableto the positive (+) jump point of thedischarged battery vehicle.
2.Connect the other end of the positive(+) jumper cable to the positive (+)terminal of the booster vehicle battery.
3.Connect the negative (-) jumper cableto the negative (-) terminal of thebooster vehicle battery.
4.Make the final connection of thenegative (-) jumper cable to thenegative (-) ground point of thedischarged battery vehicle.
5.Unlock the driver door. See Unlockingand Locking the Doors Using theRemote Control (page 81).
JUMP STARTING THE VEHICLE
To Start Your Vehicle
1.Run the engine of the booster vehicleat a moderately high speed.
2.Move the transmission selector leverof the low charge vehicle to park (P).
3.Switch on the ready to drive mode. SeeStarting the Vehicle (page 164).
4.Run both vehicles for a minimum ofthree minutes before disconnecting thecables.
Note:Do not switch the headlamps onwhen disconnecting the cables. The peakvoltage could damage the bulbs.
Disconnect the cables in the reverse order.
POST-CRASH ALERT SYSTEM
WHAT IS THE POST-CRASHALERT SYSTEM
The system helps draw attention to yourvehicle in the event of a serious impact.
HOW DOES THE POST-CRASHALERT SYSTEM WORK
The system is designed to turn the hazardflashers on, turn the courtesy lamps on,intermittently sound the horn and unlockall doors in the event of a serious impactthat deploys an airbag or the seatbeltpretensioners.
309
2023 Mustang Mach-E (CGW) Canada/United States of America, enUSA, Edition date: 202209, DOMCrash and Breakdown InformationE338767 E338540