check oil FORD PROBE 1997 2.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1997, Model line: PROBE, Model: FORD PROBE 1997 2.GPages: 288, PDF Size: 1.64 MB
Page 21 of 288
17
*
[IS05400(ALL)01/96]
The fuel gauge indicator may vary slightly while
the vehicle is in motion. This is the result of fuel
movement within the tank. You can get a more
accurate reading with the vehicle on smooth,
level ground.
[IS05500(ALL)01/96]
Charging System Gauge
[IS05600(ALL)01/96]
This gauge tells you your battery's voltage when
you turn your ignition key to ON. When you
start your engine, the pointer should move to
the NORMAL range if you are not operating
any electrical accessories. (If electrical accessories
are operating and the engine is not running, the
pointer may move into the red area).
[IS05700(ALL)01/96]
If the pointer moves into the red area when no
electrical accessories are operating, have the
vehicle's electrical system checked.
%*
[IS05800(ALL)04/96]
Engine Oil Pressure Gauge
[IS05900(ALL)01/96]
The gauge needle should stay in the NORMAL
range (indicating normal engine oil pressure). If
the needle drops below the NORMAL range into
the low range, there is a loss of oil pressure.
[IS06000(ALL)01/96]
If this happens:
*
[IS06100(ALL)04/96]
1. Pull off the road as soon as safely possible.
*
[IS06200(ALL)04/96]
2. Shut off the engine immediately or severe
engine damage could result.
[IS06300(ALL)01/96]
3. Check the oil level when the vehicle is on
level ground.
[IS06400(ALL)01/96]
4. Add only as much oil as the engine needs
before you drive the vehicle again. Do not
overfill the oil reservoir. For more
information, seeAdding engine oilin the
Index.
File:03prisp.ex
Update:Thu May 16 09:43:45 1996
Page 193 of 288
191 %
*
[MC06500(ALL)01/96]
Checking and Adding Engine Oil
*
[MC06600(ALL)01/96]
Since the proper amount of engine oil is
important for safe engine operation, check the oil
using the dipstick each time you put fuel in
your vehicle. Remember the engine must be off,
the oil must be warm and the vehicle must be
parked on level ground.
%*
[MC06700(ALL)01/96]
Checking the engine oil level:
*
[MC06800(ALL)01/96]
1. Turn the engine off after it has warmed up
and allow a few minutes for the engine oil
to drain back into the oil pan.
*
[MC06900(ALL)01/96]
2. Set the parking brake fully and make sure
that the gearshift is securely latched in P
(Park) (automatic transaxle) or 1 (First)
(manual transaxle).
*
[MC07000(ALL)01/96]
3. Open the hood. Protect yourself from engine
heat.
*
[MC07100(ALL)01/96]
4. Locate the engine oil dipstick (highlighted in
yellow) and carefully pull it out of the
engine.
*
[MC07200(ALL)01/96]
5. Wipe the dipstick clean and put it back into
position, making sure it is fully seated.
[MC07300(ALL)01/96]
one inch art:0032075-A
Engine oil dipstick
File:11prmcp.ex
Update:Thu May 16 12:08:53 1996
Page 194 of 288
192 [MC07400(ALL)01/96]6. Carefully, pull the dipstick out again. If the
oil level is below the L line, add engine oil
as necessary. If the oil level is beyond the
letter F, engine damage or high oil
consumption may occur and some oil must
be removed from the engine.
*
[MC07500(ALL)01/96]
7. Put the dipstick back in and make sure it is
fully seated.
%*
[MC07600(ALL)01/96]
Adding engine oil
*
[MC07700(ALL)01/96]
It may be necessary to add some oil between oil
changes. Make sure you use a CERTIFIED
engine oil of the preferred viscosity. Your
vehicle's warranty coverage may not apply if
engine damage is caused by the use of improper
engine oil.
*
[MC07800(ALL)01/96]
Add engine oil through the oil filler cap
highlighted in yellow. To add oil, remove the
filler cap and use a funnel to pour oil into the
opening. Be careful not to overfill the engine.
Recheck the oil level after you finish adding oil.
%*
[MC07900(ALL)01/96]
Changing the Engine Oil and the Oil Filter
*
[MC08000(ALL)01/96]
Change the engine oil and oil filterper the
following, whichever occurs first.
*
[MC08100(ALL)01/96]
one third page art:0060618-C
File:11prmcp.ex
Update:Thu May 16 12:08:53 1996
Page 195 of 288
193
*
[MC08200(ALL)02/96]
Refer to theMaintenance Schedulebooklet for
additional information.
%*
[MC08250(ALL)05/96]
NOTE: Always dispose of used automotive
fluids in a responsible manner. Follow
your community's standards for
disposing of these types of fluids. Call
your local recycling center to find out
about recycling automotive fluids.
*
[MC08275(ALL)05/96]
NOTE: Ford production and aftermarket
(Motorcraft) oil filters are designed for
added engine protection and long life.
If a replacement oil filter is used that
does not meet Ford material and design
specifications, startup engine noises or
knock may be experienced. It is
recommended you use the appropriate
Motorcraft oil filter (or another brand
meeting Ford specifications) for your
engine application.
*
[MC08300(ALL)01/96]
RWARNING
Continuous contact with USED motor oil
has caused cancer in laboratory mice.
*
[MC08400(ALL)01/96]
Protect your skin by washing with soap and
water.
%
*
[MC08450(ALL)05/96]
Brake Fluid
*
[MC08500(ALL)01/96]
Under normal circumstances, your vehicle
should not use up brake fluid rapidly. However,
expect the level of the brake fluid to slowly fall
as you put more mileage on your vehicle and
the brake pads wear.
[MC08600(ALL)01/96]
Check the brake fluid at least once a year. You
can do this by looking at the fluid level in the
plastic reservoir on the master cylinder. (SeeThe
Engine Typesearlier in this chapter to locate the
master cylinder.) The fluid level should be at or
near the MAX mark.
File:11prmcp.ex
Update:Thu May 16 12:08:53 1996
Page 205 of 288
203
*
[MC18900(ALL)01/96]
If you must add transaxle fluid in an emergency,
use only MERCONHfluid, such as Motorcraft
MERCONHMulti-Purpose ATF. Add the fluid in
1/2-pint increments until you raise the fluid
level to within the crosshatched area on the
dipstick. Never overfill the transaxle. If the fluid
level gets too high, remove the excess fluid as
soon as possible; otherwise, you could damage
the transaxle.
*
[MC18950(ALL)01/96]
Manual Transaxle Fluid
*
[MC19000(ALL)01/96]
The lubricant level and quality should not
deteriorate under normal use. However, you
should periodically have your Ford Dealer check
the fluid level during regular oil changes.
%*
[MC19100(ALL)05/96]
NOTE: Always dispose of used automotive
fluids in a responsible manner. Follow
your community's standards for
disposing of these types of fluids. Call
your local recycling center to find out
about recycling automotive fluids.
[MC19200(ALL)01/96]
Constant Velocity Joints
[MC19300(ALL)01/96]
Inspect all rubber boots for signs of cracks, tears,
or splits. Inspect underneath of your car for any
indication of grease splatter in the areas of
constant velocity joint boots, outboard and
inboard locations; grease splatter is an indication
of boot and/or clamp damage.
%
*
[MC19500(ALL)01/96]
Battery
*
[MC19600(ALL)01/96]
The Motorcraft maintenance-free battery does
not require additional water during its life of
service. The vents are part of the cover and
cannot be removed. For longer, trouble-free
operation, keep the top of the battery clean and
dry. Also, make certain the battery cables are
tightly fastened to the battery terminals.
File:11prmcp.ex
Update:Thu May 16 12:08:53 1996
Page 208 of 288
206
*
[MC21000(ALL)02/96]
If the acid touches someone's skin, eyes, or
clothing, immediately flush the area with water
for at least 15 minutes. If someone swallows the
acid, have him or her drink lots of milk or water
first, then Milk of Magnesia, a beaten egg, or
vegetable oil. Call a doctor immediately.
%*
[MC21100(ALL)02/96]
RWARNING
Applying too much pressure on the ends
when lifting a battery could cause acid to
spill. Lift the battery with a carrier or
with your hands on the opposite corners.
[MC24000(ALL)04/96]
Wiper blade maintenance
*
[MC24100(ALL)01/96]
Check the windshield wiper blades at least twice
a year. Also check them whenever they seem
less effective than usual. Such substances as tree
sap and some hot wax treatments used by
commercial car washes reduce the effectiveness
of wiper blades.
*
[MC24200(ALL)01/96]
If the blades do not wipe properly, clean both
the windshield and the wiper blades. Use
undiluted windshield washer solution or a mild
detergent. Rinse thoroughly with clear water. Do
not use fuel, kerosene, paint thinner, or other
solvents to clean your wiper blades. These will
damage your blades.
*
[MC24300(ALL)01/96]
To make reaching the wiper blades easy, simply
turn the ignition switch to ACC and turn your
wipers on. Wait for them to reach a vertical
position and turn the ignition to OFF. Do not
move the wipers manually. Moving the wipers
manually may damage them.
File:11prmcp.ex
Update:Thu May 16 12:08:53 1996
Page 225 of 288
223
*
[MC38500(ALL)01/96]
To make sure that the catalytic converter and the
other emission control parts continue to work
properly:
*
[MC38600(ALL)01/96]
q
Use only unleaded fuel.
*
[MC38700(ALL)01/96]
q
Avoid running out of fuel.
*
[MC38800(ALL)01/96]
q
Do not turn off the ignition while your
vehicle is moving, especially at high speeds.
*
[MC38900(ALL)01/96]
q
Do not push start your vehicle.
*
[MC38950(ALL)03/96]
q
Have the services listed in yourMaintenance
Schedulebooklet performed according to the
specified schedule.
*
[MC39000(ALL)01/96]
RWARNING
Do not park, idle, or drive your vehicle in
dry grass or other dry ground cover. The
emission system heats up the engine
compartment and exhaust system, which
can start a fire.
*
[MC39100(ALL)01/96]
Watch for fluid leaks, strange odors, smoke, loss
of oil pressure, the charge warning light, the
check engine light, or the temperature warning
light. These sometimes indicate that the emission
system is not working properly.
*
[MC39200(ALL)01/96]
Do not make any unauthorized changes to your
vehicle or engine. Changes that cause more
unburned fuel to reach the exhaust system can
increase the temperature of the engine or
exhaust system.
%*
[MC39300(ALL)01/96]
In general, maintenance, replacement, or service
of the emission control devices or systems in
your new Ford Motor Company vehicle or
engine may be performed at your expense by
any automotive repair establishment or
individual using automotive parts equivalent to
those with which your vehicle or engine was
originally equipped.
File:11prmcp.ex
Update:Thu May 16 12:08:53 1996
Page 271 of 288
Index 275
Index
A
ABS warning light
(see Anti-lock brake system)....... 13
Accessory position on the ignition..... 61
Additives, engine oil.......... 190
Air bag supplemental restraint system
and child safety seats......... 113
description............104, 106
driver air bag..........104, 106
indicator light............. 11
operation.............. 106
passenger air bag........... 106
service and information labels..... 106
tone generator............ 110
Air cleaner filter, specifications...... 237
Air conditioning, electronic automatic
temperature control system....... 49
Aluminum wheels............ 214
Antenna, radio (see Electronic
sound system)........... 21,43
Antifreeze (see Engine coolant)...... 196
Anti-lock brake system (ABS)
description.............. 133
see also Brake............ 133
warning light.............. 13
warninig light............. 12
Assistance (see Customer assistance) . . . 245
Audio system (see Electronic
sound system)............. 21
Autolamp system (see Headlamps)..... 63
Automatic transaxle
driving with............. 138
fluid, adding............. 201
fluid, checking............ 201
File:prixp.ex
Update:Tue Jun 11 11:04:36 1996
Page 276 of 288
280 Index
Engine
check engine warning light....... 15
does not start...........128, 130
fuel injected engine, starting...... 125
fuel pump shut-off switch....... 130
preparing to start........... 125
starting................ 126
starting after a collision........ 130
storing your vehicle.......... 234
Engine block heater........... 129
Engine coolant
checking and adding......... 196
checking hoses............ 199
disposal...........184, 193, 203
preparing for storage......... 236
proper solution........184, 193, 203
temperature gauge........... 18
Engine coolant temperature gauge
description............... 18
mechanical............... 18
Engine coolant temperature
gauge:electronic............. 18
Engine fan............... 184
Engine:idle speed control......... 128
Engine oil
changing oil and oil filter....... 191
checking and adding......... 191
dipstick............... 191
disposal...........184, 193, 203
engine oil pressure gauge........ 17
filter, specifications.......... 237
specifications............. 190
synthetic oil............. 190
ªbreak-inº oils............. 6
viscosity............... 190
Exhaust fumes............. 130
File:prixp.ex
Update:Tue Jun 11 11:04:36 1996
Page 280 of 288
284 Index
K
Keys
positions of the ignition......... 61
stuck in lock position.......... 61
L
Lamps
checking............... 225
daytime running light system...... 63
dome lamps.............. 58
flashing the lamps............ 66
fog lamps............... 57
hazard flashers............ 155
instrument panel, dimming....... 58
interior lamps.............. 58
replacing bulbs............ 225
Lane change indicator
(see Turn signal).......... 62,67
Lights, warning and indicator
airbag................. 11
anti-lock brakes (ABS).......... 13
brake................. 12
check engine.............. 15
engine oil pressure........... 17
hazard warning light......... 155
high beam............... 15
oil pressure............... 17
rear ABS................ 13
safety belt............... 11
service engine soon........... 15
testing the warning lights....... 126
turn signal indicator......... 62,67
Load limits
GAWR................ 151
GVWR................ 151
trailer towing............. 153
File:prixp.ex
Update:Tue Jun 11 11:04:36 1996