lock FORD RANGER 1996 2.G User Guide

Starting Your Ranger
43
%*
[ST03076(ALL)02/95]
Removing the Key From the Ignition
*
[ST03100(ALL)08/95]
Procedures for removing your key from the ignition will vary,
depending on the type of gearshift your vehicle has. Gearshift
levers may be mounted on the steering column or on the floor
or console.
[ST03117(ALL)05/91]
If you have a manual transmission, you have a key release lever
which allows you to remove your key from the ignition. The
key release lever is on the upper right of the steering column,
just above the key lock cylinder.
*
[ST03300(ALL)08/95]
If your vehicle's gearshift lever is mounted on the
column:
*
[ST03400(ALL)06/95]1.
Put the gearshift in P (Park).
*
[ST03500(ALL)03/91]2.
Set the parking brake fully before removing your foot from
the service brake. (This will avoid ªbindingº or ªloadingº the
park gear if you park on a grade.)
*
[ST03600(ALL)03/95]3.
Turn the ignition key to LOCK.
*
[ST03700(ALL)03/95]4.
Remove the key.
*
[ST03800(ALL)05/95]
If your vehicle's gearshift lever is mounted on the
floor:
*
[ST03950(ALL)05/95]1.
Put the gearshift in 1 (First).
*
[ST04000(ALL)05/95]2.
Turn the ignition key to OFF.
*
[ST04100(ALL)05/95]3.
Set the parking brake fully before removing your foot from
the service brake.
*
[ST04200(ALL)05/95]4.
Push and hold in the key release button.
*
[ST04300(ALL)05/95]5.
Turn the key to LOCK.
*
[ST04400(ALL)05/95]6.
Remove the key.
File:04unstr.ex
Update:Wed May 1 13:44:22 1996

Starting Your Ranger
47
%*
[ST07300(ALL)10/95]
A computer system controls the engine's idle speed. When you
start your vehicle, the engine's idle speed normally runs high.
These faster engine speeds will make your vehicle coast slightly
faster than its normal idle speed. It should, however, slow down
after a short time. If it does not, have the idle speed checked.
*
[ST07390(ALL)07/95]
If the engine idle speed does not slow down automatically, do
not allow your vehicle to idle for more than 10 minutes. Have
the vehicle checked.
*
[ST07400(ALL)05/95]
RWARNING
Extended idling at high engine speeds can produce very
high temperatures in the engine and exhaust system,
creating the risk of fire or other damage.
*
[ST07450(ALL)05/95]
RWARNING
Do not park, idle, or drive your vehicle in dry grass or
other dry ground cover. The emission system heats up
the engine compartment and exhaust system, which can
start a fire.
*
[ST07500(ALL)03/95]
If you consistently start your vehicle in subzero temperatures,
use an engine block heater (if your vehicle has this option).
%*
[ST07600(ALL)06/95]
Engine Block Heater (If equipped)
*
[ST07700(ALL)03/95]
Engine block heaters are strongly recommended if you live in a
region where temperatures reachs20ÊF (s29ÊC) orbelow
consistently during the winter months. An engine block heater
warms the engine coolant, which improves starting, warms up
the engine faster, and allows the heater-defrost system to
respond quickly.
File:04unstr.ex
Update:Wed May 1 13:44:22 1996

48
*
[ST08000(ALL)05/95]
RWARNING
To prevent electrical shock, do not use your heater with
ungrounded electrical systems or two-pronged (cheater)
adapters.
*
[ST08100(ALL)03/95]
For best results, plug the heater in at least three hours before
you start your vehicle. Using the heater for longer than three
hours will not damage the engine, so you can plug it in at night
to start your vehicle the following morning.
*
[ST08150(ALL)12/91]
NOTE: Be sure to disconnect the engine block heater before
driving your vehicle.
%*
[ST08175(ALL)03/95]
If the Engine Cranks but Does Not Start or
Does Not Start After a Collision
*
[ST08200(ALL)07/95]
The Fuel Pump Shut-off Switch
*
[ST08210(ALL)10/95]
If the engine cranks but does not start or does not start after a
collision, the fuel pump shut-off switch may have been
triggered. The shut-off switch is a device intended to stop the
fuel pump when your vehicle has been involved in a major jolt.
*
[ST08215(ALL)03/95]
Once the shut-off switch is triggered, you must reset the switch
by hand before you can start your vehicle.
File:04unstr.ex
Update:Wed May 1 13:44:22 1996

Warning Lights and Gauges
57
*
[LG03800(ALL)02/95]
Anti-lock Brake Warning Light
[LG03925(ALL)03/95]
To check the ABS brake warning light, turn the ignition key to
ON. The ABS brake warning light should glow momentarily.
[LG03985(R )09/95]
NOTE: If the ABS brake warning light does not glow
momentarily, have your vehicle's electrical system
checked immediately. If the light begins to flash in a
repeatable flash sequence, check the anti-lock system
continuous power fuse and brakelamps for proper
operation.
[LG04050(ALL)06/94]
6 pica art:0021146-A
Anti-lock warning light symbol
*
[LG04100(ALL)05/95]
RWARNING
If the anti-lock brake system warning light remains on or
comes on while driving, have the braking system checked
by a qualified service technician as soon as possible.
*
[LG04110(ALL)10/95]
NOTE: If a fault occurs in the anti-lock system, and the brake
warning light is not lit, the anti-lock system is
disabled but normal brake function remains
operational.
%*
[LG04150(ALL)07/95]
Safety Belt Warning Light and Chime
*
[LG04301(ALL)08/95]
The safety belt warning light/chime reminds you to fasten your
safety belt. One of the following will take place:
[LG04325(ALL)03/95]
n
If the safety belt is not buckled when the key is turned to
the ON position, the light comes on for 60 seconds and the
chime sounds for 4 to 8 seconds.
File:05unlgr.ex
Update:Wed May 1 13:45:37 1996

Warning Lights and Gauges
63
*
[LG06100(ALL)07/95]
This light comes on every time you turn the ignition to the ON
or START position (engine off). The light should go off when
the engine starts and the alternator begins to charge.
*
[LG06300(ALL)01/95]
If the light stays on or comes on when the engine is running,
have the electrical system checked as soon as possible.
[LG06335(ALL)04/95]
This light flashes on and off when the ignition switch is OFF
and any door is opened. As soon as you lock the doors, the
light glows steadily. Within 30 seconds of closing all the doors,
the light flashes intermittently (every 2 seconds). This indicates
that the alarm system is armed.
[LG06350(ALL)10/94]
Check Gage Light (If equipped)
*
[LG06355(ALL)06/94]
This light will come on when the key is in the ON position and
the:
[LG06360(ALL)06/94]
n
engine coolant temperature is high
[LG06365(ALL)06/94]
n
engine oil pressure is low
[LG06370(ALL)06/94]
n
fuel level is near empty
[LG06375(ALL)06/94]
This light serves as a notice that a system needs your attention
and to check the engine coolant temperature gauge, the engine
oil pressure gauge, and the fuel level gauge.
[LG06380(ALL)03/95]
Please seeEngine Coolant Temperature Gauge,Engine Oil Pressure
Gauge,orFuel Gaugein this chapter for more information.
[LG06385(ALL)10/94]
6 pica art:0021250-B
Check gage light
File:05unlgr.ex
Update:Wed May 1 13:45:37 1996

74
[IP00350(R )10/94]
The main controls for the climate control system, lights, lamps,
clock, and radio are on the instrument panel.
%*
[IP00475(ALL)09/95]
NOTE: Any cleaner or polish that increases the gloss (shine)
of the upper part of the instrument panel should be
avoided. The dull finish in this area is to help protect
the driver from undesirable windshield reflection.
%*
[IP00500(ALL)06/95]
The Climate Control Systems
*
[IP00601(ALL)12/91]
Your vehicle is equipped with a control assembly designed to
handle either a combination A/C-Heater System or a
Heater-Only System.
%*
[IP00801(ALL)10/93]
Instrument Panel Registers
*
[IP00901(ALL)02/95]
There are four registers in the instrument panel. Each of these
registers contains a louver assembly which can be manually
adjusted to direct airflow up, down, left and right. An
illustration of the register locations follows.
[IP01201(ALL)04/94]
7-1/2 pica art:0020099-D
Instrument panel registers
[IP01400(ALL)12/91]
Air Conditioning (A/C) Controls (Manual Air
Conditioning)
*
[IP01450(ALL)02/95]
The control for your air conditioning and heater system is
located at the center of the instrument panel below the radio
and will operate only when the ignition key is turned to the
ON position. Your air conditioner and heater will heat and/or
cool your vehicle interior depending on the function position
File:06unipr.ex
Update:Wed May 1 13:46:22 1996

78
*
[IP02750(ALL)03/95]
n
Do not put objects under the front seats that interfere with
the flow of air to the back seat area.
[IP02800(ALL)03/95]
n
Remove any snow, ice, or leaves from the air intake area of
your air conditioner and heater system that could block the
air intake. The intake area is located at the bottom of the
windshield.
*
[IP02900(R )08/94]
Heater Controls (Heater-Only Vehicles)
[IP02950(R )03/95]
The control for your heater system is located at the center of the
instrument panel below the radio. The heater will operate only
when the ignition key is turned to the ON position. Your heater
will heat and/or ventilate your vehicle interior depending on
the function position and temperature you select. The function
selector control knob allows you to select heating or ventilation
and determine where the air will be directed. The temperature
control knob setting determines the temperature of the air that
flows into the vehicle.
[IP03000(R )06/95]
10-1/2 pica
art:0090206-A
Climate control knobs (heater only)
[IP03050(R )03/95]
To turn your heater system on, select any position except OFF.
This turns the fan on and allows airflow into the vehicle. To
turn your heater off, select OFF.
File:06unipr.ex
Update:Wed May 1 13:46:22 1996

Instrument Panel Controls
83
*
[IP17890(ALL)05/95]
RWARNING
The Daytime Running Light (DRL) system will not
illuminate the tail lamps and parking lamps. Turn on
your headlamps at dusk. Failure to do so may result in a
collision.
%*
[IP17900(ALL)03/95]
Lighting Up the Instrument Panel and the Interior of
Your Vehicle
[IP18000(ALL)10/94]
The instrument panel lights can be turned on by turning the
headlamp knob toward either the first or second position. You
can brighten or dim the instrument panel lights by rotating the
thumb wheel.
[IP18200(ALL)03/95]
The interior lights will shut off after 25 seconds with all the
doors closed, or immediately when the ignition switch is turned
to the ON position, or if the vehicle speed is above five MPH
(8 km/h). The interior lights will turn off after 40 minutes if
any of the doors are left open. Refer toBattery Saverin the
Featuressection for more details.
[IP18500(R )11/89]
Courtesy and Dome Lamps
[IP19175(R )04/94]
The interior/courtesy lamp is automatically turned on when the
driver or passenger door is opened. Turning the thumb wheel
fully counterclockwise will operate the interior lamp when the
doors are closed.
[IP19185(R )08/94]
7-1/2 pica art:0021156-B
Interior/Courtesy lamp
File:06unipr.ex
Update:Wed May 1 13:46:22 1996

Instrument Panel Controls
85
[IP19700(ALL)04/95]
Dome/Map Lamps (If equipped)
[IP19825(R )08/91]
The map lamps are located on each side of the dome light
assembly. You can turn the individual map lamps on or off by
sliding the switch to the left or right. To turn off, slide the
switch to the middle.
[IP19950(R )04/94]
7-1/2 pica art:0020895-B
Map lamps
*
[IP20300(ALL)04/95]
Clock Controls on Electronic Radios
[IP20400(ALL)10/94]
The electronic radios have a built-in clock. For complete
operating instructions, refer toElectronic Sound Systemsin this
Owner Guide.
File:06unipr.ex
Update:Wed May 1 13:46:22 1996

Steering Column Controls
93
*
[SC06450(ALL)09/95]
To change the position of the steering wheel, push the release
lever under the steering column away from you. Tip the
steering wheel to the desired position. Pull the lever back into
place to lock the steering wheel.
*
[SC07250(ALL)12/89]
Be sure the steering wheel locks in a notch. It is not infinitely
adjustable. Do not adjust the steering wheel while the vehicle is
in motion.
%*
[SC07300(ALL)03/91]
Speed Control (If equipped)
*
[SC07400(ALL)06/95]
If your vehicle has speed control, you can automatically
maintain a constant speed at or above 30 mph (50 km/h).
*
[SC07450(ALL)06/95]
Use of radio transmitting equipment that is not Federal
Communications Commission (FCC) or in Canada the Canadian
Radio and Telecommunications Commission (CRTC) approved
may cause the speed control to malfunction. Therefore, use only
properly installed FCC (CRTC in Canada) approved radio
transmitting equipment in your vehicle.
[SC07500(ALL)10/94]
7-1/2 pica art:0020091-F
The speed control switches
*
[SC07800(ALL)08/95]
To set the speed control:
*
[SC08000(ALL)08/95]1.
Press and release the ON switch.
[SC08100(ALL)02/95]2.
Accelerate to the desired speed above 30 mph (48 km/h)
using the accelerator pedal.
File:07unscr.ex
Update:Wed May 1 13:46:58 1996