lock FORD RANGER 1996 2.G Workshop Manual

Driving Your Ranger
175
*
[DR19700(R )08/94]
n
Manual locking hubs must be in LOCK position before
shifting into four-wheel drive.
*
[DR19800(ALL)11/89]
When using four-wheel drive, maintain steering wheel control at
all times, especially in rough terrain. Since sudden changes in
terrain can result in abrupt steering wheel motion, make sure
you grip the steering wheel rim from the outside. Do not grip
the spokes.
*
[DR19900(ALL)05/90]
Drive cautiously to avoid vehicle damage from concealed objects
such as rocks and stumps. Know the terrain or examine maps of
the area in question before driving. Map out your route
beforehand. To maintain steering and braking control of your
vehicle, you must have all four tires on the ground, and they
must be rolling, not sliding or spinning.
[DR19925(ALL)10/94]
Transmission upshift in 4WD with transfer case in 4WD LOW
may be quite firm due to large total gear reduction. This
condition is normal.
*
[DR20000(ALL)11/89]
Sand
*
[DR20100(ALL)11/89]
When driving over sand, try to keep all four wheels of the
vehicle on the most solid area of the trail. Do not reduce the
tire pressures but shift to a lower gear and drive steadily
through the terrain. Apply accelerator slowly and avoid
spinning the wheels.
*
[DR20200(ALL)11/89]
Mud and Water
*
[DR20300(ALL)12/89]
When driving through water, determine the depth; avoid water
higher than the bottom of the hubs (if possible) and proceed
slowly. If the ignition system gets wet, the vehicle may stall.
*
[DR20400(ALL)11/89]
Once through water, always try the brakes. Wet brakes do not
stop the vehicle as effectively as dry brakes. Drying can be
improved by moving your vehicle slowly, while applying light
pressure on the brake pedal.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

178
*
[DR22400(ALL)05/95]
RWARNING
An increase in pedal travel will result in reduced braking
capability. The brake system should be checked
immediately.
%*
[DR22500(R )10/94]
Rear Anti-lock Brakes
*
[DR22750(R )10/94]
Your vehicle may be equipped with a Rear Anti-lock Brake
System. This system prevents at least one and often both rear
wheels from completely locking up when the brakes are applied
in a panic stop, for example.
*
[DR22800(R )07/94]
Even with the Anti-lock Brake System, you should be careful
when braking. Front brake lock up on any surface, even on
smooth pavement causes loss of steering control. Heavy braking
on roads with loose surfaces such as snow or gravel, or severe
pavement irregularities could also cause you to lose steering
control of your vehicle.
*
[DR22900(R )05/95]
RWARNING
If the anti-lock brake system warning light remains on or
comes on while driving, have the braking system checked
by a qualified service technician as soon as possible.
*
[DR22901(R )10/95]
NOTE: If a fault occurs in the anti-lock system, and the brake
warning light is not lit, the anti-lock system is
disabled but normal brake function remains
operational.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

Driving Your Ranger
179
[DR22905(ALL)10/94]
Four Wheel Anti-lock Brake System
*
[DR22912(R )08/94]
Your vehicle may be equipped with a Four Wheel Anti-lock
Braking System (4WABS). The 4WABS helps the driver to
maintain vehicle control by preventing wheel lockup during
hard braking.
*
[DR22915(ALL)03/94]
The 4WABS operates with a computer that is able to optimize
vehicle control during braking on varying tire and road
conditions by modulating the brake pressure at each of the front
wheels and the rear axle. This ªpumping actionº is similar to
the driver ªpumpingº the brakes but happens at a much faster
rate.
*
[DR22920(ALL)05/95]
RWARNING
The Anti-lock system does NOT assist the vehicle in
stopping quickly on wet or icy surfaces. Heavy braking
combined with poor road conditions could cause you to
lose steering control of your vehicle.
*
[DR22925(ALL)10/94]
Using anti-lock brakes
*
[DR22930(ALL)05/94]
The operation of a vehicle with 4WABS is not similar to the
operation of normal brakes. Some differences exist and are listed
below:
*
[DR22935(ALL)10/94]
n
Apply the brake steadily. In the event of a panic stop, do
NOT ªpumpº the brakes. ªPumpingº the brakes during an
Anti-lock stop will diminish braking effectiveness.
%*
[DR22940(ALL)10/94]
n
During an Anti-lock stop, the driver will notice a brake
pedal pulsation and hear some noise from the engine
compartment. This is an indication that the 4WABS system is
working correctly and is normal.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

180
*
[DR22945(ALL)05/95]
RWARNING
The Anti-lock system does NOT decrease the time
necessary to apply the brakes. Always leave enough room
between the vehicle in front of you and your vehicle.
*
[DR22950(ALL)05/95]
4WABS driver warning light
[DR22955(ALL)10/94]
The 4WABS computer continuously monitors the system while
driving for any electrical faults or system malfunctions. In
addition, the 4WABS computer performs an initial system check
called bulb proveout when the vehicle ignition is switched on.
During bulb proveout, the ABS light on the instrument cluster
will momentarily illuminate and then go out.
*
[DR22960(ALL)09/95]
NOTE: After starting the vehicle and upon initial drive-off,
the driver may notice a single pulse of the brake
pedal and a noise from the engine compartment. This
is part of the initial system check and is normal.
[DR22965(ALL)05/95]
Should a malfunction in the 4WABS system occur, the ABS light
on the instrument cluster will come on and stay on indicating
that the anti-lock system has been shut down and the vehicle
needs to be serviced. Normal braking is not affected unless the
brake warning light is also illuminated.
*
[DR22970(ALL)09/95]
NOTE: It is important to note that when the ABS Warning
Light is illuminated the ABS system is disabled. The
vehicle must be serviced immediately to restore the
benefits of the Anti-lock system.
*
[DR22975(ALL)09/95]
NOTE: Mobile phones or radio transmitters not installed by
Ford Motor Company may interfere with the Anti-lock
System. Should the Anti-lock system activate
unexpectedly or the Anti-lock Warning Light
illuminate after installation of such a unit, have the
installation of the unit checked.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

Driving Your Ranger
183
[DR24930(ALL)05/95]
17-1/2 pica
art:0020568-D
Parking brake
*
[DR24950(ALL)03/95]
RWARNING
When parking, do not use the gearshift in place of the
parking brake. Turn the key to LOCK whenever you
leave your vehicle. Always set the parking brake fully
and make sure that the gearshift is securely latched in P
(Park) (automatic transmission) or in 1 (First) (manual
transmission). Never leave your vehicle unattended while
it is running. If you do not take these precautions, your
vehicle may move unexpectedly and injure someone.
*
[DR24970(R )05/95]
With the transfer case in N (Neutral), the vehicle is free to move
with either the automatic transmission in P (Park) or with the
manual transmission in any driving gear.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

186
[DR27001(ALL)01/95]
n
Pump the brake pedal steadily and evenly to avoid locking
your front wheels (except with 4WABS).
[DR27025(ALL)05/95]
n
To stop on ice, shift to N (Neutral) below 10 mph (15 km/h)
and gently pump brakes (except with 4WABS).
*
[DR27050(ALL)02/93]
n
Consider using one of the lower gears.
*
[DR27101(ALL)05/91]
n
For 4x4 vehicles, engage 4WD, and try to drive slowly away.
*
[DR27150(ALL)05/95]
RWARNING
To avoid losing control on slippery roads, do not
downshift into Low with the automatic transmission
when moving faster than 20 mph (32 km/h). Do not
downshift into First with the manual transmission when
moving faster than 5 mph (8 km/h).
*
[DR27350(R )06/94]
RWARNING
The rear antilock brake system may not prevent brake
lock-up on extremely slippery surfaces. Rear brake
lock-up may also occur while driving in four-wheel drive
because the transfer case couples the front and rear axles
together.
%*
[DR27450(ALL)03/95]
Traction-Lok Rear Axle (If equipped)
*
[DR27501(ALL)03/95]
This axle provides added drive away traction on slippery
surfaces, particularly when one or more wheels are on a surface
with poor traction.
*
[DR27550(ALL)03/93]
Extended use of other than matching size tires on a
Traction-Lok rear axle could result in a permanent reduction in
effectiveness. This loss of effectiveness does not affect normal
driving and should not be noticeable to the driver.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

192Vehicle Loading/Towing Informationand the Trailer Towing Tables
to determine the specific towing capability of your vehicle.
*
[DR29050(ALL)02/92]
n
Stay within the load limits when you tow.
*
[DR29101(ALL)01/95]
n
Carefully and thoroughly prepare your vehicle for towing,
making sure to use the right equipment and to attach it
properly. (SeePreparing to Towin this chapter.)
*
[DR29151(ALL)01/95]
n
Use extra caution when driving your vehicle while you tow.
(SeeDriving while you towin this chapter.)
*
[DR29201(ALL)01/95]
n
Service your vehicle more frequently if you tow a trailer.
(SeeServicing your vehicle if you towin this chapter.)
*
[DR29350(ALL)05/94]
Do not tow a trailer until your vehicle has been driven at least
500 miles (800 km).
%*
[DR29401(ALL)06/92]
Vehicle Loading/Towing Information
*
[DR29450(ALL)03/91]
Your vehicle's load capacity is designated by weight, not
volume, so you cannot necessarily use all available space with
large or heavy loads. Maximum safe vehicle weights as well as
tire, rim sizes and inflation pressures are specified for your
vehicle at the assembly plant on the Safety Compliance
Certification Label. The Certification Label is located on the left
front door lock facing or the door latch post pillar.
*
[DR29501(ALL)12/91]
Trucks, unlike passenger cars, are basically custom vehicles
designed to carry a load. Most owners start with a base vehicle
and add production and dealer installed and/or aftermarket
components to suit their tastes and purposes. Even trucks that
are purchased for personal transportation only are likely to have
considerable optional equipment, such as step bumpers and
light bars, for example.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

Roadside Emergencies
227
%*
[RE15200(ALL)03/95]
Preparing to Change the Tire
*
[RE15250(ALL)12/91]
NOTE: To lift your vehicle by other than the front or rear
jacking points, be sure to use only hoist adapters with
a wide contact surface.
*
[RE15300(ALL)03/91]1.
Make sure that your vehicle will not move or roll. If you
have an automatic transmission, put the gearshift in Park. If
you have a manual transmission, put the gearshift in
Reverse. Set the parking brake and block the wheel that is
diagonally opposite the tire that you are changing.
*
[RE15335(ALL)12/91]
NOTE: Make sure the ignition is in the OFF position.
*
[RE15350(R )06/94]
If you have a four-wheel drive vehicles with manual locking
hubs, put transfer case lever in 2H, 4H, or 4L.
*
[RE15390(ALL)05/95]
When one of the back wheels is off the ground, the transmission
alone will not prevent the vehicle from moving or slipping off
the jack, even if the vehicle is in P (Park) or 1 (First). To
prevent the vehicle from moving when you change a tire, be
sure the parking brake is set, then block the wheel (both
directions) that is diagonally opposite (other side and end of the
vehicle) to the tire that is being changed.
[RE15400(ALL)05/95]
RWARNING
If the vehicle slips off the jack, someone could be
seriously injured.
*
[RE15440(R )05/95]
RWARNING
Do not leave the vehicle unattended with the transfer
case in the N (Neutral) position. Always set the parking
brake fully and turn off the ignition when leaving the
vehicle.
*
[RE15550(ALL)03/95]2.
Get out the spare tire and jack.
File:12unrer.ex
Update:Wed May 1 13:53:18 1996

Roadside Emergencies
229
[RE16800(ALL)07/94]3.
Insert the tapered end of the lug nut wrench behind wheel
covers or hubcaps and twist off.
[RE16830(ALL)05/95]
RWARNING
Use only the lug nut wrench provided to remove wheel
ornaments. Not using the tapered end of the lug nut
wrench at the pry-off notches may result in damage to
the finish of the wheel and ornament.
[RE16850(ALL)06/94]
RWARNING
Not using the tapered end of the lug nut wrench at the
pry-off notches may result in damage to the finish of the
wheel and ornament.
*
[RE16900(ALL)10/89]4.
Loosen the wheel nuts by pulling up on the handle of the
lug nut wrench about one-half turn (counterclockwise). Do
not remove the wheel lug nuts until you raise the tire off the
ground.
*
[RE17100(ALL)02/95]5.
Insert the jack handle into the jack and use the handle to
slide the jack under the vehicle.
*
[RE17175(ALL)05/95]
RWARNING
To avoid injury, never run the engine with one wheel off
the ground, such as when changing a tire.
%*
[RE17225(ALL)05/95]
Removing and Replacing the Tire
%*
[RE17300(ALL)06/95]1.
Positioning the jack
[RE18150(R )06/94]
a. To raise a front wheel, place the jack directly under the
shock absorber so that it contacts the bottom of the shock.
[RE18201(R )11/89]
b. To raise a rear tire place the jack under the rear axle
between the spring shackle bolts.
File:12unrer.ex
Update:Wed May 1 13:53:18 1996

230
[RE18301(R )10/94]
10-1/2 pica art:0020297-E
Front axle jacking point
[RE18401(ALL)06/94]
c. Turn the jack handle clockwise until the wheel is a
maximum of one inch off the ground.
[RE18551(R )10/94]
10-1/2 pica
art:0021187-B
Rear axle jacking point
[RE18650(ALL)09/95]
NOTE: Do not use the differential housing as a lift point.
File:12unrer.ex
Update:Wed May 1 13:53:18 1996