ABS FORD RANGER 1996 2.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1996, Model line: RANGER, Model: FORD RANGER 1996 2.GPages: 369, PDF Size: 3.48 MB
Page 25 of 369
Safety Restraints
23
%*
[SR09600(ALL)08/95]
Safety Belt Extension Assembly
*
[SR09700(ALL)07/95]
For some people, the safety belt may be too short even when it
is fully extended. You can add about eight inches (20 cm) to the
belt length with a safety belt extension assembly (part number
611C22). Safety belt extensions are available at no cost from
your dealer.
*
[SR09790(ALL)08/95]
Use only extensions manufactured by the same supplier as the
safety belt. Manufacturer identification is located at the end of
the webbing on the label. Also, use the safety belt extension
only if the safety belt is too short for you when fully extended.
Do not use extension to change the fit of the shoulder belt
across the torso.
*
[SR09800(ALL)08/95]
RWARNING
Failure to follow these instructions will affect the
performance of the safety belts and increase the risk of
personal injury.
%*
[SR09900(ALL)08/95]
Safety Belt Maintenance
*
[SR10000(ALL)09/95]
Check the safety belt systems periodically to make sure that
they work properly and are not damaged.
[SR10030(R )06/95]
The short plastic boot on the front safety belt at the outboard
anchor location (Regular Cab, driver; SuperCab, driver and
passenger) covers an energy absorbing sew pattern on the safety
belt. In the event of an accident, the sew pattern may release,
and the colored label (REPLACE BELT) may become visible. If
this occurs,the safety belt must be replaced.
File:03unsrr.ex
Update:Wed May 1 13:43:56 1996
Page 26 of 369
24
[SR10035(ALL)06/95]
33-1/2 pica
art:0021286-B
Energy absorbing sew pattern
File:03unsrr.ex
Update:Wed May 1 13:43:56 1996
Page 41 of 369
Safety Restraints
39
[SR18501(ALL)09/95]
Follow the child seat manufacturer's instructions to attach the
tether strap to the tether bracket.
*
[SR18950(ALL)06/95]
RWARNING
Only use the tether attachment hole locations shown in
the illustrations. The tether anchor may not perform
properly if the wrong mounting location is used.
*
[SR19595(R )05/95]
In Super Cabs equipped with Center Facing Jump Seats, the
tether strap anchor bracket should be installed only at the center
of the cab's back panel with the child seat in the front center
seating position. Installing an anchor bracket at the right rear of
the cab may increase risk of injury to an occupant of the right
rear center facing jump seat in the event of a collision or
sudden stop. If a tethered child seat is installed in the right
front seating position, secure the tether strap to the webbing of
the buckled right rear lap belt.
*
[SR19600(R )05/95]
RWARNING
Do not install a child seat in a center facing jump seat.
%*
[SR19700(ALL)07/95]
Safety Belts for Children
*
[SR19800(ALL)07/95]
Children who are too large for child safety seats should always
wear safety belts. (See instructions with your child seat, or
contact its manufacturer, to determine maximum size of child
that will safely fit in the seat.)
*
[SR19900(ALL)07/95]
RWARNING
If safety belts are not properly worn and adjusted as
described, the risk of serious injury to the child in a
collision will be much greater.
File:03unsrr.ex
Update:Wed May 1 13:43:56 1996
Page 58 of 369
Warning Lights and Gauges
57
*
[LG03800(ALL)02/95]
Anti-lock Brake Warning Light
[LG03925(ALL)03/95]
To check the ABS brake warning light, turn the ignition key to
ON. The ABS brake warning light should glow momentarily.
[LG03985(R )09/95]
NOTE: If the ABS brake warning light does not glow
momentarily, have your vehicle's electrical system
checked immediately. If the light begins to flash in a
repeatable flash sequence, check the anti-lock system
continuous power fuse and brakelamps for proper
operation.
[LG04050(ALL)06/94]
6 pica art:0021146-A
Anti-lock warning light symbol
*
[LG04100(ALL)05/95]
RWARNING
If the anti-lock brake system warning light remains on or
comes on while driving, have the braking system checked
by a qualified service technician as soon as possible.
*
[LG04110(ALL)10/95]
NOTE: If a fault occurs in the anti-lock system, and the brake
warning light is not lit, the anti-lock system is
disabled but normal brake function remains
operational.
%*
[LG04150(ALL)07/95]
Safety Belt Warning Light and Chime
*
[LG04301(ALL)08/95]
The safety belt warning light/chime reminds you to fasten your
safety belt. One of the following will take place:
[LG04325(ALL)03/95]
n
If the safety belt is not buckled when the key is turned to
the ON position, the light comes on for 60 seconds and the
chime sounds for 4 to 8 seconds.
File:05unlgr.ex
Update:Wed May 1 13:45:37 1996
Page 134 of 369
134
*
[AS29505(ALL)08/95]
n
Using the ªSEEKº function with your cassette tape player
*
[AS29510(ALL)08/95]
While in the tape mode, push the right (
a) side of the
ªSEEKº button to seek forward to the next selection on the
tape. Push the left (
b) side to seek the previous tape
selection.
*
[AS29515(ALL)08/95]
n
Using the ªSCANº function with your cassette tape player
*
[AS29520(ALL)01/95]
Press the ªSCANº button to begin the forward scan mode on
the tape currently playing, stopping on each tape selection
for approximately an eight-second sampling (display
indicates ªSCº).
*
[AS29525(ALL)01/95]
To stop the scan mode on the presently sampled tape
selection, press ªSCANº a second time.
*
[AS29530(ALL)08/95]
n
How to change the side of the tape being played
*
[AS29535(ALL)01/95]
The alternate side of the tape can be selected by pressing the
ªSIDE 1-2º button.
*
[AS29540(ALL)08/95]
How to eject the tape
*
[AS29545(ALL)01/95]
To stop the tape and eject the cassette, press the ªEJº button.
The radio will resume playing if the radio power is on. The
tape cartridge can be ejected with radio power (and/or ignition)
on or off.
[AS29550(ALL)06/95]
How to switch from tape to AM/FM mode
*
[AS29555(ALL)01/95]
Press the ªAM/FMº button to stop the tape player and resume
radio play.
*
[AS29560(ALL)08/95]
Using the DolbyHB noise reduction feature
*
[AS29565(ALL)08/95]
NOTE: Noise reduction system manufactured under license
from Dolby Labs Licensing Corporation. ªDolbyº and
double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
*
[AS29570(ALL)04/95]
Push thekbutton to activate Dolby B Noise Reduction. Push
again to deactivate.
File:09unasr.ex
Update:Wed May 1 13:49:43 1996
Page 150 of 369
150
*
[AS30200(R )08/95]
n
Using the ºSEEKª function with your cassette tape player
*
[AS30205(R )08/95]
While in the tape mode, push the right (
a) side of the
ºSEEKª button to seek forward to the next selection on the
tape. Push the left (
b) side to seek the previous tape
selection.
*
[AS30210(R )08/95]
n
Using the ºSCANª function with your cassette tape player
*
[AS30215(R )01/95]
Press the ºSCANª button to begin the forward scan mode on
the tape currently playing, stopping on each tape selection
for approximately an eight-second sampling (display
indicates ºSCª).
*
[AS30220(R )01/95]
To stop the scan mode on the presently sampled tape
selection, press ºSCANª a second time.
*
[AS30225(R )08/95]
n
How to change the side of the tape being played
*
[AS30230(R )01/95]
The alternate side of the tape can be selected by pressing the
ºSIDE 1-2ª button.
*
[AS30235(R )08/95]
How to eject the tape
*
[AS30240(R )01/95]
To stop the tape and eject the cassette, press the ºEJª button.
The radio will resume playing if the radio power is on. The
tape cartridge can be ejected with radio power (and/or ignition)
on or off.
[AS30245(R )06/95]
HowtoswitchfromtapetoAM/FMmode
*
[AS30247(R )01/95]
Press the ºAM/FMª button to stop the tape player and resume
radio play.
*
[AS30250(R )08/95]
Using the DolbyHB noise reduction feature
*
[AS30255(R )08/95]
NOTE: Noise reduction system manufactured under license
from Dolby Labs Licensing Corporation. ºDolbyª and
double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
File:09unasr.ex
Update:Wed May 1 13:49:43 1996
Page 179 of 369
Driving Your Ranger
179
[DR22905(ALL)10/94]
Four Wheel Anti-lock Brake System
*
[DR22912(R )08/94]
Your vehicle may be equipped with a Four Wheel Anti-lock
Braking System (4WABS). The 4WABS helps the driver to
maintain vehicle control by preventing wheel lockup during
hard braking.
*
[DR22915(ALL)03/94]
The 4WABS operates with a computer that is able to optimize
vehicle control during braking on varying tire and road
conditions by modulating the brake pressure at each of the front
wheels and the rear axle. This ªpumping actionº is similar to
the driver ªpumpingº the brakes but happens at a much faster
rate.
*
[DR22920(ALL)05/95]
RWARNING
The Anti-lock system does NOT assist the vehicle in
stopping quickly on wet or icy surfaces. Heavy braking
combined with poor road conditions could cause you to
lose steering control of your vehicle.
*
[DR22925(ALL)10/94]
Using anti-lock brakes
*
[DR22930(ALL)05/94]
The operation of a vehicle with 4WABS is not similar to the
operation of normal brakes. Some differences exist and are listed
below:
*
[DR22935(ALL)10/94]
n
Apply the brake steadily. In the event of a panic stop, do
NOT ªpumpº the brakes. ªPumpingº the brakes during an
Anti-lock stop will diminish braking effectiveness.
%*
[DR22940(ALL)10/94]
n
During an Anti-lock stop, the driver will notice a brake
pedal pulsation and hear some noise from the engine
compartment. This is an indication that the 4WABS system is
working correctly and is normal.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996
Page 180 of 369
180
*
[DR22945(ALL)05/95]
RWARNING
The Anti-lock system does NOT decrease the time
necessary to apply the brakes. Always leave enough room
between the vehicle in front of you and your vehicle.
*
[DR22950(ALL)05/95]
4WABS driver warning light
[DR22955(ALL)10/94]
The 4WABS computer continuously monitors the system while
driving for any electrical faults or system malfunctions. In
addition, the 4WABS computer performs an initial system check
called bulb proveout when the vehicle ignition is switched on.
During bulb proveout, the ABS light on the instrument cluster
will momentarily illuminate and then go out.
*
[DR22960(ALL)09/95]
NOTE: After starting the vehicle and upon initial drive-off,
the driver may notice a single pulse of the brake
pedal and a noise from the engine compartment. This
is part of the initial system check and is normal.
[DR22965(ALL)05/95]
Should a malfunction in the 4WABS system occur, the ABS light
on the instrument cluster will come on and stay on indicating
that the anti-lock system has been shut down and the vehicle
needs to be serviced. Normal braking is not affected unless the
brake warning light is also illuminated.
*
[DR22970(ALL)09/95]
NOTE: It is important to note that when the ABS Warning
Light is illuminated the ABS system is disabled. The
vehicle must be serviced immediately to restore the
benefits of the Anti-lock system.
*
[DR22975(ALL)09/95]
NOTE: Mobile phones or radio transmitters not installed by
Ford Motor Company may interfere with the Anti-lock
System. Should the Anti-lock system activate
unexpectedly or the Anti-lock Warning Light
illuminate after installation of such a unit, have the
installation of the unit checked.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996
Page 186 of 369
186
[DR27001(ALL)01/95]
n
Pump the brake pedal steadily and evenly to avoid locking
your front wheels (except with 4WABS).
[DR27025(ALL)05/95]
n
To stop on ice, shift to N (Neutral) below 10 mph (15 km/h)
and gently pump brakes (except with 4WABS).
*
[DR27050(ALL)02/93]
n
Consider using one of the lower gears.
*
[DR27101(ALL)05/91]
n
For 4x4 vehicles, engage 4WD, and try to drive slowly away.
*
[DR27150(ALL)05/95]
RWARNING
To avoid losing control on slippery roads, do not
downshift into Low with the automatic transmission
when moving faster than 20 mph (32 km/h). Do not
downshift into First with the manual transmission when
moving faster than 5 mph (8 km/h).
*
[DR27350(R )06/94]
RWARNING
The rear antilock brake system may not prevent brake
lock-up on extremely slippery surfaces. Rear brake
lock-up may also occur while driving in four-wheel drive
because the transfer case couples the front and rear axles
together.
%*
[DR27450(ALL)03/95]
Traction-Lok Rear Axle (If equipped)
*
[DR27501(ALL)03/95]
This axle provides added drive away traction on slippery
surfaces, particularly when one or more wheels are on a surface
with poor traction.
*
[DR27550(ALL)03/93]
Extended use of other than matching size tires on a
Traction-Lok rear axle could result in a permanent reduction in
effectiveness. This loss of effectiveness does not affect normal
driving and should not be noticeable to the driver.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996
Page 229 of 369
Roadside Emergencies
229
[RE16800(ALL)07/94]3.
Insert the tapered end of the lug nut wrench behind wheel
covers or hubcaps and twist off.
[RE16830(ALL)05/95]
RWARNING
Use only the lug nut wrench provided to remove wheel
ornaments. Not using the tapered end of the lug nut
wrench at the pry-off notches may result in damage to
the finish of the wheel and ornament.
[RE16850(ALL)06/94]
RWARNING
Not using the tapered end of the lug nut wrench at the
pry-off notches may result in damage to the finish of the
wheel and ornament.
*
[RE16900(ALL)10/89]4.
Loosen the wheel nuts by pulling up on the handle of the
lug nut wrench about one-half turn (counterclockwise). Do
not remove the wheel lug nuts until you raise the tire off the
ground.
*
[RE17100(ALL)02/95]5.
Insert the jack handle into the jack and use the handle to
slide the jack under the vehicle.
*
[RE17175(ALL)05/95]
RWARNING
To avoid injury, never run the engine with one wheel off
the ground, such as when changing a tire.
%*
[RE17225(ALL)05/95]
Removing and Replacing the Tire
%*
[RE17300(ALL)06/95]1.
Positioning the jack
[RE18150(R )06/94]
a. To raise a front wheel, place the jack directly under the
shock absorber so that it contacts the bottom of the shock.
[RE18201(R )11/89]
b. To raise a rear tire place the jack under the rear axle
between the spring shackle bolts.
File:12unrer.ex
Update:Wed May 1 13:53:18 1996