air condition FORD RANGER 1997 2.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1997, Model line: RANGER, Model: FORD RANGER 1997 2.GPages: 361, PDF Size: 3.39 MB
Page 68 of 361
Controls and Features
65
[CF01400(R)01/96]
Air Conditioning (A/C) Controls (Manual Air
Conditioning)
*
[CF01450(R)03/96]
The control for your air conditioning and heater system is
located at the center of the instrument panel below the radio
and will operate only when the ignition key is turned to the
ON position. Your air conditioner and heater will heat and/or
cool your vehicle interior depending on the function position
and temperature you select. The function selector control knob
allows you to select heating or cooling and determine where the
air will be directed. The temperature control knob setting
determines the temperature of the air that flows into the vehicle.
[CF01500(R)01/96]
10-1/2 pica
art:0020589-G
Climate control knobs
*
[CF01550(R)03/96]
To turn your air conditioner and heater system on, select any
position except OFF. This will turn the fan on and allow airflow
into the vehicle. To turn your air conditioner and heater off,
select OFF. This will turn the fan off and stop airflow from
coming into the vehicle.
File:05uncfr.ex
Update:Thu Mar 20 08:51:14 1997
Page 70 of 361
Controls and Features
67
*
[CF02050(R)03/96]
MAX A/C
[CF02100(R)01/96]
The MAX A/C position produces cool air more rapidly to
provide faster cooling of your vehicle. This is possible because
cooler air is drawn from inside the passenger area and
refrigerated again instead of using warmer outside air. Using
inside air will also make the fan sound louder and is normal
when using MAX A/C. The air flow will be from the
instrument panel registers.
[CF02150(R)01/96]
S(Panel and Floor)
[CF02200(R)01/96]
SelectSto direct airflow to the floor and through the
instrument panel registers at the same time. This selection can
be used to either heat or cool your vehicle. The air conditioner
will operate to cool the air if the outside temperature is about
50ÊF (10ÊC) orwarmer.
[CF02250(R)04/96]
R(Floor)
[CF02300(R)01/96]
SelectRto direct air to the floor. The air cannot be cooled in
theRposition but can be heated by rotating the temperature
knob into the red area.
[CF02350(R)01/96]
P(Floor and Defrost)
[CF02400(R)01/96]
SelectPto direct air to the floor and windshield defrosters at
the same time. If the outside temperature is about50ÊF (10ÊC)
or warmer, the air will also be dehumidified to remove
moisture. This feature will help prevent fogging in humid
weather. The air can be cooled or heated.
% [CF02450(R)04/96]
V(Defrost)
[CF02500(R)01/96]
SelectVto obtain maximum airflow to the windshield. Rotate
the temperature knob into the red area for the air temperature
required to defrost. When the outside temperature is about50ÊF
(10ÊC) or warmer, the airwill be dehumidified to remove
moisture. Rotate the
Hknob to increase the airflow.
File:05uncfr.ex
Update:Thu Mar 20 08:51:14 1997
Page 71 of 361
68
*
[CF02550(R)01/96]
Operating tips
*
[CF02600(R)03/96]
The following tips will help you to get the most satisfaction
from your air conditioning (if equipped) and heater system.
[CF02650(R)01/96]
n
In humid weather, selectVbefore starting your engine.
This will help to prevent windshield fogging. After a few
minutes of operation, you may select another function.
[CF02700(R)01/96]
n
To prevent humidity buildup inside your vehicle, always
drive with the air conditioner or heater system turned on.
*
[CF02750(R)01/96]
n
Do not put objects under the front seats that interfere with
the flow of air to the back seat area.
[CF02800(R)01/96]
n
Remove any snow, ice, or leaves from the air intake area of
your air conditioner and heater system that could block the
air intake. The intake area is located at the bottom of the
windshield.
*
[CF02900(R)01/96]
Heater Controls (Heater-Only Vehicles)
[CF02950(R)01/96]
The control for your heater system is located at the center of the
instrument panel below the radio. The heater will operate only
when the ignition key is turned to the ON position. Your heater
will heat and/or ventilate your vehicle interior depending on
the function position and temperature you select. The function
selector control knob allows you to select heating or ventilation
and determine where the air will be directed. The temperature
control knob setting determines the temperature of the air that
flows into the vehicle.
File:05uncfr.ex
Update:Thu Mar 20 08:51:14 1997
Page 124 of 361
122
[SS10040(R)01/96]
RWARNING
FAILURE TO REPLACE THE SAFETY BELT ASSEMBLY
UNDER THE ABOVE CONDITIONS COULD RESULT
IN SEVERE PERSONAL INJURIES IN THE EVENT OF
A COLLISION.
[SS10200(R)05/96]
All safety belt assemblies, including retractors, buckles, front
seat belt buckle support assemblies (slide bar) (if equipped)
shoulder belt height adjusters (if equipped) child safety seat
tether bracket assemblies (if equipped), and attaching hardware,
should be inspected after any collision. Ford recommends that
all safety belt assemblies used in vehicles involved in a collision
be replaced. Hoever, if the collision was minor and a qualified
technician finds that the belts do not show damage and
continue to operate properly, they do not need to be replaced.
Safety belt assemblies not in use during a collision should also
be inspected and replaced if either damage or improper
operation is noted.
%*
[SS10300(R)05/96]
Air Bag Supplemental Restraint System
(SRS)
*
[SS10800(R)05/96]
The driver and right front passenger air bags are Supplemental
Restraint Systems (SRS), provided at these seating positions in
addition to the lap/shoulder belt, and are designed to
supplement the protection provided to properly belted
occupants in moderate to severe frontal collisions. The
supplemental air bag system does not provide restraint to the
lower body.
File:06unssr.ex
Update:Fri Mar 21 09:43:41 1997
Page 131 of 361
Seating and Safety Restraints
129
%*
[SS13050(R)05/96]
The air bag system uses a readiness light on the instrument
cluster and a tone to indicate the condition of the system. When
you turn the ignition key to the ON position, this light will
illuminate for approximately six (6) seconds and then turn off.
This indicates that the system is operating normally. NOTE:
Maintenance of the air bag system is not required.
*
[SS13060(R)01/96]
17-1/2 pica
art:0050087-A
Inflated driver-side air bag
File:06unssr.ex
Update:Fri Mar 21 09:43:41 1997
Page 154 of 361
Starting
153
*
[TO10400(R)01/96]
If the engine is idling while you are stopped in an open area
for long periods of time, open the windows at least one inch
(2.5 cm). Also, adjust the heating or air conditioning system to
bring in outside air.
[TO10650(R)01/96]
n
HEATING Ð Set fan speed to medium or high, the function
control knob on any position except OFF and the
temperature control knob on any desired position.
[TO10700(R)01/96]
n
AIR CONDITIONING Ð Set fan speed to medium or high
with the function control knob on any position (except OFF
or MAX A/C) and the temperature control knob at a
comfortable level.
*
[TO13076(R)03/96]
Removing the Key From the Ignition
*
[TO13100(R)03/96]
Procedures for removing your key from the ignition will vary,
depending on the type of gearshift your vehicle has. Gearshift
levers may be mounted on the steering column or on the floor
or console.
[TO13117(R)01/96]
If you have a manual transmission, you have a key release lever
which allows you to remove your key from the ignition. The
key release lever is on the upper right of the steering column,
just above the key lock cylinder.
*
[TO13300(R)03/96]
If your vehicle's gearshift lever is mounted on the
column:
*
[TO13400(R)03/96]1.
Put the gearshift in P (Park).
*
[TO13500(R)03/96]2.
Set the parking brake fully before removing your foot from
the service brake. (This will avoid ªbindingº or ªloadingº the
park gear if you park on a grade.)
*
[TO13600(R)03/96]3.
Turn the ignition key to LOCK.
*
[TO13700(R)03/96]4.
Remove the key.
File:08untor.ex
Update:Thu Mar 20 08:53:27 1997
Page 195 of 361
194
*
[GF30650(R)01/96]
It is important to remember that GVWis not a limit or a
specification.If an owner loads up a vehicle and weighs it, that's
the GVW at that moment. If the owner piles on more of a load
and weighs it again, that becomes the GVW.
%*
[GF30701(R)01/96]
Gross Vehicle Weight Rating (GVWR)
*
[GF30750(R)01/96]
To avoid overloading a vehicle, the owner should observe the
manufacturer's specified Gross Vehicle Weight Rating. The
GVWR is the maximum total weight of base vehicle, passengers,
optional components and cargo that a particular vehicle was
designed to carry.
%*
[GF30801(R)01/96]
Gross Axle Weight Rating (GAWR)
*
[GF30850(R)01/96]
We have all seen a car or a truck that is loaded down in the
rear and riding high in the front. This is a dangerous condition
that usually means that the rear suspension components are
under severe strain and that vehicle handling is impaired. There
is more to carrying a load than just payload or GVWR.
*
[GF30901(R)01/96]
Your Safety Compliance Certification Label not only gives the
GVWR, it also gives the Gross Axle Weight Rating (GAWR)
which is the carrying capacity for each axle system. For trucks,
the rear axle will be designed to carry more weight than the
front.
*
[GF30950(R)01/96]
The rating is based on the carrying capacity of thelowest rated
axle and suspension component as well as other factors. This is
why it's so important to observe vehicle loading ratings.
Overloading a vehicle punishes components and can lead to
shortened service life or outright failure.
*
[GF31001(R)01/96]
The capacity of the tires is included as part of the axle and
suspension system, which is to be considered when determining
the lowest rated component. Tires are rated to carry a specific
maximum load at a specific maximum tire pressure.
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997
Page 250 of 361
250
%*
[MC01400(R)05/96]
NOTE: Always dispose of used automotive fluids in a
responsible manner. Follow your community's
standards for disposing of these types of fluids. Call
your local recycling center to find out about recycling
automotive fluids.
%*
[MC01600(R)01/96]
Precautions When Servicing Your Vehicle
*
[MC01700(R)01/96]
Be especially careful when inspecting or servicing your vehicle.
Here are some general precautions for your safety:
*
[MC01900(R)01/96]
n
If you must work with the engine running, avoid wearing
loose clothing or jewelry that could get caught in moving
parts. Take appropriate precautions with long hair.
*
[MC02000(R)01/96]
n
Do not work on a vehicle in an enclosed space with the
engine running, unless you are sure you have enough
ventilation.
*
[MC02100(R)01/96]
n
Never get under a vehicle while it is supported only by a
jack. If you must work under a vehicle, use safety stands.
*
[MC02200(R)01/96]
n
Keep all lit cigarettes and other smoking materials away
from the battery and all fuel-related parts.
*
[MC02500(R)01/96]
If you disconnect the battery, the engine must ªrelearnº its idle
conditions before your vehicle will drive properly. To find out
how the engine does this, seeBatteryin this chapter.
*
[MC02600(R)01/96]
Working with the engine off:
*
[MC02660(R)01/96]1.
Set the parking brake fully and make sure that the gearshift
is securely latched in P (Park).
*
[MC02700(R)01/96]2.
Remove the key from the ignition after you turn the engine
off.
*
[MC02725(R)01/96]3.
Block the wheels. This will prevent your vehicle from
moving unexpectedly.
File:11unmcr.ex
Update:Thu Mar 20 08:58:43 1997
Page 290 of 361
290
*
[MC32510(R)01/96]
A venting fuel tank is not an abnormal condition. It may be
caused by:
[MC32520(R)01/96]
n
Too volatile a fuel for the weather conditions. The service
stations sometimes sell winter grade fuel in the spring.
*
[MC32530(R)01/96]
n
Pulling a heavy load on hot days, or at high altitudes.
*
[MC32540(R)01/96]
n
Extended periods of idling with the engine RPM increased
above the normal idle range.
*
[MC32550(R)01/96]
n
Parking vehicle in full sunlight for extended periods on
extremely hot days.
%*
[MC32580(R)01/96]
Choosing the Right Fuel
*
[MC32592(R)05/96]
Use only UNLEADED FUEL. The use of leaded fuel is
prohibited by law and could damage your vehicle. The damage
may not be covered by your warranty.
*
[MC32600(R)05/96]
Your vehicle was not designed to use fuel containing
manganese-based additives such as MMT. Additionally, vehicles
certified to California emission standards (indicated on the
underhood Vehicle Emissions Control Information label) are
designed to operate on California reformulated gasolines. If
California reformulated gasoline is not available when you
refuel, your vehicle can be operated on non-California fuels.
However, even though your engine will perform adequately on
other gasolines, the performance of the emission control devices
and systems may be adversely affected. Repair of damage
caused by using a fuel that your vehicle was not designed for
may not be covered by your warranty.
[MC32620(R)05/96]
Octane Recommendations
*
[MC32640(R)05/96]
Your vehicle is designed to use regular gasoline with an
(R+M)/2 octane rating of 87.We do not recommend gasolines
labeled as ªregularº in high altitude areas that are sold with
octane ratings of 86 or even less.
File:11unmcr.ex
Update:Thu Mar 20 08:58:43 1997
Page 291 of 361
Maintenance and Care
291
[MC32660(R)05/96]
one inch art:0060001-C
Typical octane rating label
*
[MC32680(R)05/96]
Do not be concerned if your vehicle sometimes knocks lightly.
However, if it knocks heavily under most driving conditions on
the recommended octane fuel, see your dealer or a qualified
service technician to prevent any engine damage.
[MC32700(R)05/96]
Fuel Quality
*
[MC32720(R)05/96]
If you are experiencing starting, rough idle or hesitation
problems, try a different brand of fuel. If the condition persists,
see your dealer or a qualified service technician.
*
[MC32730(R)05/96]
The American Automobile Manufacturers Association (AAMA)
issued a gasoline specification to provide information on high
quality fuels that optimize the performance of your vehicle. We
recommend the use of gasolines that meet the AAMA
specification if they are available.
*
[MC32740(R)05/96]
It should not be necessary to add any aftermarket products to
your fuel tank if you continue to use a high-quality fuel.
[MC32742(R)05/96]
Cleaner Air
*
[MC32744(R)05/96]
Ford approves the use of gasolines to improve air quality,
including reformulated gasolines, that contain oxygenates such
as a maximum of 10% ethanol or 15% MTBE. There should be
no more than 5% methanol with cosolvents and additives to
protect the fuel system.
File:11unmcr.ex
Update:Thu Mar 20 08:58:43 1997