suspension FORD SIERRA 1986 1.G Braking System Workshop Manual

the caliper, and the caliper body is modified
accordingly. Also, plastic covers are fitted to
the caliper guide bolts (see illustrations).
22Procedures are unchanged from those
given above.
Rear disc pads
23Slacken the rear roadwheel nuts, chock
the front wheels, then jack up the rear of the
vehicle and support on axle stands. (see
“Jacking and Vehicle Support”). Remove the
roadwheel.
24The disc pads can be inspected through
the top of the caliper after removal of the
blanking spring clip. Check that the friction
material thickness is not less than the
minimum given in the Specifications.
25If any one of the pads has worn below the
specified limit, the rear pads must be renewedas an axle set (4 pads).
26To renew the pads, proceed as follows.
27Release the handbrake, and free the
handbrake cable from the suspension lower
arm by bending back the tangs.
28Where applicable, disconnect the wiring
to the disc pad wear sensor (see illustration).
29Unscrew and remove the bolt from the
forward caliper guide pin, while holding the
pin stationary with a spanner (see
illustration).
30Swing the caliper rearwards and lift out
the disc pads (see illustration). Do not
depress the brake pedal with the caliper
removed.
31Brush all dirt and dust from the caliper,
pads and disc, but do not inhale it as it may
be injurious to health. Scrape any corrosion
from the disc.32As the new pads will be thicker than the
old ones, the piston must be retracted into its
bore to accommodate the new thicker pads.
Retracting the piston will cause the fluid level
in the reservoir to rise, so to avoid spillage,
syphon out some fluid using an old
hydrometer or a teat pipette. Retract the
caliper piston by turning it clockwise. Ford
tool No 12-006 is designed for this purpose,
but a pair of circlip pliers or any similar tool
can be used instead (see illustration).
33Remove the backing paper from the new
pads, and fit them to the caliper.
34Further refitting is a reversal of removal,
bearing in mind the following points.
35If disc pads with wear sensors are fitted,
the pad with the sensor wire should be fitted
inboard.
36Repeat the procedure on the opposite
rear brake.
37On completion, switch on the ignition and
apply the footbrake hard several times to
settle the pads. Switch off the ignition, then
check and if necessary top-up the fluid level in
the reservoir. Check the operation of the
handbrake.
38Avoid heavy braking, if possible, for the
first hundred miles or so after fitting new
pads. This will allow the pads to bed in and
reach full efficiency.
Braking system 10•5
10
4.21a Later type front disc pad retaining
clip
4.32 Retracting the piston using circlip
pliers4.30 Lift out the disc pads
4.28 Rear disc pad wear sensor wiring clip
(arrowed)
4.29 Unscrewing the forward caliper guide
pin bolt
4.21b Removing a caliper guide bolt cover
- later type
4.20b Refitting the caliper retaining clip -
Teves caliper4.20a The clip on the back of the inboard
disc pad fits into the piston recess - Teves
caliper

Note: Complete dismantling of the rear caliper
should not be attempted unless Ford spring
compressor (tool No 12-007) is available, or
unless the problems likely to arise in the
absence of the tool are understood. Renewal
of the piston seal dust-excluding seal and
piston adjuster nut seal requires no special
tools.
Removal
1With the ignition switched off, pump the
brake pedal at least 20 times, or until it
becomes hard, to depressurise the system.
2Chock the front wheels, slacken the
relevant roadwheel nuts, then jack up the rear
of the vehicle and support on axle stands (see
“Jacking and Vehicle Support”). Remove the
roadwheel and release the handbrake.
3Where applicable, disconnect the wiring to
the disc pad wear sensor.
4Proceed as described in Section 6,
paragraphs 2 and 3, but note that the rigid
brake pipe is clipped to the suspension lower
arm.
5Unscrew and remove the two guide bolts
securing the caliper to the carrier bracket,
while holding the pins with a spanner. Unhookthe handbrake cable from the lever, and
withdraw the caliper. Alternatively, the two
carrier bracket-to-hub carrier bolts can be
unscrewed, and the caliper and carrier can be
separated on the bench, but in this case the
handbrake cable must be disconnected from
the carrier bracket by removing the retaining
circlip.
Overhaul
6Clean the caliper, taking care not to inhale
any dust which may be injurious to health, and
mount it in a soft-jawed vice.
7Rotate the piston anti-clockwise, using
Ford tool No 12-006, or a pair of circlip pliers
or similar tool, until it protrudes from the
caliper bore by approximately 20.0 mm (0.8
in). Free the dust-excluding seal from the
groove in the piston, then continue
unscrewing the piston and remove it. Remove
and discard the dust-excluding seal.
8The piston and bore may now be cleaned
and examined as described in Section 6,
paragraph 12.
9The piston adjuster nut seal should be
renewed as follows.
10Remove the circlip from the piston, then
extract the thrustwashers, wave washer and
thrust bearing. Note the fitted sequence of
these components. Finally remove the nut
(see illustrations).
11Remove the seal from the nut, noting
which way round it is fitted. Clean the nut with
methylated spirit. Lubricate the new seal with
clean hydraulic fluid and fit it to the nut.12If no further dismantling is required,
proceed to paragraph 20.
13For further dismantling it is virtually
essential to have Ford tool 12-007 in order to
compress the adjuster spring. This tool
appears to be a cut-down adjuster nut with a
handle for turning it. In the workshop it was
found that the actual piston adjuster nut could
be used to compress the spring if it were
turned with circlip pliers (see illustration).
This works well enough for dismantling, but
reassembly proved extremely difficult
because of the limited clearance between the
skirt of the nut and the caliper bore.
14Having compressed the adjuster spring
just enough to take the load off the circlip,
release the circlip inside the caliper bore.
Remove the spring compressor, then extract
the circlip, spring cover, spring and washer
(see illustrations).
7Rear disc caliper - removal,
overhaul and refitting
10•10Braking system
7.10a Remove the circlip from the rear
caliper piston . . .7.10c . . . a wave washer and (not shown)
another thrustwasher . . .
7.14a Extract the circlip from the caliper
bore . . .
7.13 Using the piston adjuster nut to
compress the adjuster spring7.10e . . . and finally the adjuster nut itself.
Note the seal (arrowed) on the nut7.10d . . . then the thrust bearing . . .
7.10b . . . followed by the thrustwasher . . .
Caution: Refer to the
precautions in Section 1.

3Remove the wheel cylinder.
4Remove the driveshaft but do not refit the
securing bolts to the backplate.
5Remove the backplate.
6If required, prise out the handbrake stop
button.
7Refitting is a reversal of removal.
P 100 models
Note: When refitting the backplate, a new rear
hub nut and driveshaft O-ring must be used.
8Proceed as described in paragraphs 1 to 3
inclusive.
9Remove the driveshaft.
10Relieve the staking on the rear hub nut,
and using a 50 mm socket and a suitable
extension bar, unscrew the nut. Note that the
nut is extremely tight.
11Pull off the hub.
12Unscrew the six retaining nuts and
remove the backplate and the oil baffle (see
illustration).
13If required, prise out the handbrake stop
button.
14Refitting is a reversal of removal, bearing
in mind the following points.
15When refitting the backplate and the oil
baffle, coat the area of the oil baffle shown
(see illustration - Chapter 9) with sealant to
Ford spec SPM-4G-9112-F, then refit the
baffle and the backplate to the axle, tightening
the six securing nuts to the specified torque.
16Use a new rear hub nut, and tighten to the
specified torque. Stake the nut into the groove
in the axle tube after tightening.
17Refit the driveshaft, using a new O-ring.
Note: A suitable puller will be required to
remove the drive flange, and a new rear hub
nut must be used on reassembly.
Removal
1Loosen the rear hub nut with the vehicle
resting on its wheels. Note that the left-hand
nut has a left-hand thread, ie it is undone in a
clockwise direction. Before loosening the nut,
ensure that the handbrake is applied, and
chock the relevant rear wheel. A suitable
extension bar will be required, as the nut is
extremely tight.
2Loosen the relevant rear roadwheel nuts,
chock the front wheels, then jack up the rear
of the vehicle and support on axle stands (see
“Jacking and Vehicle Support”).Remove the
roadwheel and release the handbrake.
3Free the handbrake cable from its clip on
the suspension lower arm.
4Unscrew the two caliper carrier
bracket-to-hub carrier bolts, and remove the
caliper, supporting it on an axle stand to avoid
straining the flexible hose.
5Mark the position of the brake disc in
relation to the drive flange, remove the
retaining spire washer(s), and remove the
disc.
6Unscrew and remove the rear hub nut, and
using a suitable puller, pull off the drive flange.
7Unscrew the four bolts securing the hub
carrier and splash shield to the lower arm.
Remove the hub carrier and splash shield,
whilst supporting the driveshaft. Support the
driveshaft by placing axle stands underneath
it, or by securing with string to the underbody.
Avoid bending the driveshaft joints to
excessive angles, and do not allow the shaft
to hang down from one end.
Refitting
8Refitting is a reversal of removal, bearing in
mind the following points.
9When reassembling the drive flange and the
hub carrier, fit the drive flange to the hub
carrier in order to centralise the bearings, then
using a soft-faced mallet, drive the drive
flange/hub carrier assembly onto the end of
the stub axle.10Refit the hub carrier/splash
shield-to-lower arm securing bolts. Note that
there are two types of bolts used to secure
the rear hub carrier to the lower arm. The two
types of bolt must not be mixed on a vehicle
but can be changed in complete sets for the
alternative type. A complete set is eight bolts,
four each side. Note that the two types of bolt
have different torque wrench settings. When
renewing the wheel bearings a suitable puller
will be required to remove the drive flange,
and a new rear hub nut must be used on
reassembly.
11When refitting the brake disc, align the
previously made marks on disc and drive
flange.
12Fit a new rear hub nut of the correct type,
and tighten it with the vehicle resting on its
roadwheels. Apply the handbrake and chock
the relevant rear wheel when finally tightening
the hub nut.
Note: Before commencing overhaul obtain a
repair kit containing new pistons and seals.
Removal
1Depress the brake pedal several times to
dissipate the vacuum in the servo.
2Disconnect the wiring plug from the low
fluid level switch on the fluid reservoir cap
(see illustration).
3Place a suitable container beneath the
master cylinder, then unscrew the union nuts
and disconnect the two fluid pipes. Plug the
ends of the pipes to prevent dirt ingress.
13Master cylinder (conventional
braking system) - removal,
overhaul and refitting
12Rear disc splash shield -
removal and refitting
Braking system 10•13
10
13.2 Disconnect the wiring plug from the low fluid level switch
(arrowed)11.12 Brake backplate and oil baffle retaining nuts
Caution: Refer to the
precautions in Section 1.
Caution: Refer to the
precautions in Section 1.

4Withdraw the module, and disconnect the
multi-plug (see illustration).
Refitting
5Refitting is a reversal of removal but on
completion check the operation of the ABS
warning lamp as described in the
manufacturer’s handbook.
Note: A new O-ring must be used when
refitting a sensor.
Front wheel sensor
1Apply the handbrake, loosen the relevant
front roadwheel nuts, then jack up the front of
the vehicle and support on axle stands (see
“Jacking and Vehicle Support”). Remove the
roadwheel.
2Working under the bonnet, unclip the ABS
wiring loom from the chassis side member,
and disconnect the wheel sensor wiring plug.
3Unscrew the mounting bolt and withdraw
the sensor (see illustration).
4Refitting is a reversal of removal, bearing in
mind the following points.
5Clean the bore in the hub carrier, and smear
the bore and the sensor with lithium based
grease.
6Use a new O-ring seal when refitting the
sensor.
Rear wheel sensor
7Chock the front wheels, loosen the relevant
rear roadwheel nuts, then jack up the rear of
the vehicle and support on axle stands.
Release the handbrake and remove the
roadwheel.
8Working inside the vehicle, lift up the rear
seat cushion, then remove the side kick panel
and fold the carpet forwards to gain access to
the wheel sensor wiring plug (see
illustrations).
9Remove the wiring plug from its clip, and
disconnect it.
10Prise out the floor panel grommet, then
feed the sensor wiring through the floor panel.
11Free the handbrake cable from its clip on
the suspension lower arm.12Where applicable, disconnect the wiring
to the disc pad wear sensor.
13Unscrew and remove the bolt from the
forward caliper guide pin, while holding the
pin stationary with a spanner.
14Swing the caliper rearwards to gain
access to the wheel sensor.
15Unscrew the bolt securing the sensor to
its mounting bracket.
16Refitting is a reversal of removal, bearing
in mind the following points.
17Clean the bore in the sensor mounting
bracket, and smear the bore and the sensor
with lithium based grease.
18Use a new O-ring seal when refitting the
sensor.
Removal
1The deceleration sensitive valve is located
on the left-hand side of the engine
compartment (see illustrations).
2Place a suitable container beneath the
valve to catch spilt fluid, then unscrew the
union nuts and disconnect the fluid pipes.Plug the open ends of the pipes and valve to
prevent fluid leakage and dirt ingress. If fluid is
accidentally spilt on the paintwork, wash off
immediately with cold water.
3On early models, the valve is secured to the
mounting bracket on the inner wing by a
single bolt. Unscrew the bolt and remove the
valve.
4On later models, the valve is secured to the
mounting bracket by a clip. Remove the clip
and slide out the valve.
Refitting
5Refitting is a reversal of removal, but note
that the early type of valve must be fitted with
the cover bolts facing forwards, and the later
type of valve must be fitted with the smaller
diameter stepped end facing forwards.
6On completion, bleed the rear hydraulic
circuit.
23Deceleration sensitive valve
(all models with conventional
braking system)
- removal and refitting
22Wheel sensor (ABS)
- removal and refitting
10•18Braking system
21.4 Withdraw the module and disconnect
the multi-plug - ABS22.8a Remove the side kick panel
(securing screws arrowed) for access to
the rear wheel sensor wiring plug - ABS
23.1b Later type deceleration sensitive
valve23.1a Early type deceleration sensitive
valve
22.8b Rear wheel sensor wiring plug
(arrowed) - ABS
22.3 Unscrew the mounting bolt and
withdraw the front wheel sensor - ABS
Caution: Refer to the
precautions in Section 1.

4A flexible hose must never be installed
twisted, but a slight “set” is permissible to
give it clearance from adjacent components.
This can be achieved by turning the hose
slightly before fitting the U-shaped retaining
clip to the mounting bracket.
5Rigid pipelines can be made to pattern by
motor factors supplying brake components.
Removal
1Chock the front wheels, loosen the rear
roadwheel nuts, then jack up the rear of the
vehicle and support on axle stands. Release
the handbrake and remove the roadwheels.
2Slacken the handbrake cable adjuster.
3Extract the securing circlip and pivot pin,
and detach the handbrake equaliser from the
linkage on the underbody (see illustration).4On models with a conventional braking
system, remove the brake shoes and
disconnect the handbrake cables from the
operating levers, then disconnect the cables
from the brake backplates by extracting the
U-clips.
5On models with ABS, unhook the
handbrake cables from the operating levers
on the calipers, then disconnect the cables
from the caliper carrier brackets by removing
the retaining circlips (see illustrations).
6On Saloon, Hatchback and Estate models
bend back the tangs and release the cables
from the lower suspension arms, then feed
the cables through the holes in the
suspension crossmember and release them
from the brackets on the underbody, noting
that the right-hand cable is retained by a
circlip (see illustration). Withdraw the cable
assembly from the vehicle.
7On P100 models, release the cables from
the brackets on the chassis crossmember,
noting that the left-hand cable is retained by a
circlip, then unhook the cable support springsand withdraw the cable assembly from the
vehicle (see illustration).
Refitting
8Refitting is a reversal of removal. On
models with a conventional braking system
refit the brake shoes.
9On completion, adjust the cable.
27Handbrake cable -removal
andrefitting
10•20Braking system
27.3 Handbrake equaliser securing circlip
(arrowed) and pivot pin
27.5b Handbrake cable-to-caliper carrier bracket attachment -
ABS
27.7 Handbrake cable support spring (arrowed)27.6 Handbrake cable-to-lower suspension arm attachment
27.5a Handbrake cable-to-operating lever attachment - ABS

Note: Where fitted, the adjuster locking pin
must be renewed on completion of
adjustment.
Conventional braking system
(except P100 models)
1The handbrake cable is normally
self-adjusting in use, however adjustment
may be required to compensate for cable
stretch over a long period, and is also
necessary after fitting a new cable.
2Chock the front wheels, jack up the rear of
the vehicle and support on axle stands (see
“Jacking and Vehicle Support”).Release the
handbrake.
3Unscrew the locknut from the adjuster
located on the left-hand underbody bracket
(see illustration). On later models, a locking
pin is fitted to the bracket to lock the adjuster
nuts in position. Where applicable, remove the
locking pin before unscrewing the locknut.4Apply the footbrake vigorously several
times to set the self-adjuster mechanism.
5Turn the adjuster until the plastic plungers
located in the brake lockplates are free to
turn, and the total movement of both plungers
added together is between 0.5 and 1.0 mm
(0.02 and 0.04 in) (see illustration).
6Tighten the adjuster locknut against the
adjuster nut by hand (two clicks), then tighten
further by a minimum of two and a maximum
of four clicks, using a suitable spanner or
pliers.
7Where applicable, fit a new adjuster locking
pin. The old pin should not be re-used.
8Check that with the handbrake released,
the rear wheels are free to rotate and no brake
“bind” is evident. The handbrake lever travel
should be between two and four clicks of the
ratchet. If brake “bind” or excessive lever
travel is evident, check the handbrake cable
routing, and check the self-adjuster
mechanism for wear or damage.
ABS
9Proceed as described in paragraphs 1 to 3
inclusive.
10Bend back the tangs and release the
cables from the lower suspension arms.
11Ensure that both handbrake operating
levers are returned to their stops on the
calipers, then make alignment marks between
the levers and the caliper bodies (see
illustration).
12Turn the adjuster until either lever just
starts to move, as indicated by the alignment
marks.
13Apply the handbrake and release it
several times to equalise the cable runs.
14With the handbrake released, proceed as
described in paragraphs 6 and 7.
15Refit the cables to the lower suspension
arms, and secure by bending over the tangs.
16Check that with the handbrake released,
the rear wheels are free to rotate and no brake“bind” is evident. The handbrake lever travel
should be between two and four clicks of the
ratchet. If brake “bind” or excessive lever
travel is evident, check the handbrake cable
routing, and check the caliper mechanism for
wear or damage.
P100 models
17Proceed as described in paragraphs 1 to
4 inclusive, but note that the adjuster is
located on the right-hand side of the chassis
crossmember (see illustration).
18Apply the handbrake, pulling the lever
upwards three clicks.
19Turn the adjuster until both rear wheels
are locked and cannot be turned by hand.
20Proceed as described in paragraphs 6
and 7.
21Check that with the handbrake released,
the rear wheels are free to rotate and no brake
“bind” is evident. The handbrake lever travel
should be between three and five clicks of the
ratchet. If brake “bind” or excessive lever
travel is evident, check the handbrake cable
routing, and check the self-adjuster
mechanism for wear or damage.
28Handbrake cable - adjustment
Braking system 10•21
10
28.5 Plastic plunger (arrowed) in brake backplate
28.17 Handbrake cable adjuster on right-
hand side of chassis crossmember28.11 Make alignment marks between
each handbrake operating lever and
caliper body (arrowed) - ABS
28.3 Handbrake cable adjuster on left-hand underbody bracket
(arrowed)