alarm FORD SIERRA 1987 2.G Bodywork And Fittings Workshop Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1987, Model line: SIERRA, Model: FORD SIERRA 1987 2.GPages: 22, PDF Size: 1.2 MB
Page 10 of 22
3Remove the window channel extension
screw from the bottom rear corner of the
door, and withdraw the channel through the
lower door aperture.
4Working inside the door aperture, pull out
the lock barrel retaining clip using pliers, then
unhook the lock operating rod from the barrel,
and withdraw the barrel from outside the door
(see illustration).
Refitting
5Refitting is a reversal of removal.
Models up to 1990
1Remove the door inner trim panel.
2Where necessary for improved access, peel
back the waterproof plastic sheet from the
door.
3Withdraw the window channel extension
through the lower rear door aperture after
removing the single securing screw if working
on a front door or the two securing screws if
working on a rear door.
4Remove the three securing screws from the
rear edge of the door, then reach inside the
door and turn the lock to disconnect it from
the control rods.
5Where applicable, disconnect the “door
ajar” sensor wiring plug and the central
locking component wiring plug(s). Central
locking component removal and refitting is
covered in Chapter 13.
6Withdraw the lock from inside the door.
7Refitting is a reversal of removal, but ensure
that the window channel extension is correctly
located.
Models from 1990
8From 1990, cable-operated door locks have
been fitted to all Sierra models. To remove the
later type of lock, proceed as follows. Do not
bend or stretch the cable during removal and
refitting, as the operation of the lock will be
impaired.
9Remove the door inner trim panel.
10Where necessary for improved access,
peel back the waterproof plastic sheet from
the door.11Remove the securing screw, and
withdraw the window channel extension
through the door’s lower aperture.
12Disconnect the door outer handle and the
lock barrel (front doors) operating rods at the
lock assembly.
13Disconnect the battery negative lead, and
disconnect the door lock motor and the alarm
system wiring plugs (where applicable).
14Remove the screw securing the door
interior handle to the door panel.
15Remove the three lock securing screws
from the rear edge of the door, then withdraw
the lock assembly complete with the
operating cable and the door interior handle.
16To disconnect the cable from the lock,
proceed as follows.
17Carefully prise the cover plate from the
lock, using a screwdriver(see illustration).
18Using a suitable pair of pliers, carefully
remove the outer cable from the groove in the
lock assembly casing.
19Extend the inner cable until the flats on
the plastic end piece align with the guide, then
withdraw the cable (see illustration).
20Commence reassembly and refitting as
follows.
21Align the flats on the inner cable end piece
with the cable guide, and refit the inner cable.
22Using a suitable pair of pliers, carefully
refit the outer cable to the groove in the lock
assembly casing.
23Refit the lock cover plate.
24Insert the lock, cable and interior handle
into the door, and refit the three lock securing
screws. 25Push the interior handle assembly
towards the lock to adjust the cable, and
when adjustment is correct, refit and tighten
the interior handle securing screw.
26Further refitting is a reversal of removal,
ensuring that the window channel extension is
correctly located.
Removal
1Remove the door inner trim panel.
2Unscrew and remove the bolt securing the
check arm to the body pillar.
3Unscrew and remove the two bolts
securing the check arm to the door, and
withdraw the check arm from inside the door.
Peel back the waterproof plastic sheet where
necessary for improved access.
Refitting
4Refitting is a reversal of removal.
Note: A suitable lifting crane and tackle will be
required for this operation.
Removal
1Disconnect the battery negative lead.
2Remove the fuel filler cap, then drain the
fuel tank.
3Remove the two securing screws and
detach the fuel filler pipe from the cargo area.
4Disconnect the number plate lamp and the
rear lamp wiring plugs, and release the wiring
from the cargo area.
5Disconnect the earth lead from the right-
hand front cargo area mounting bracket
underneath the vehicle.
6Working underneath the vehicle, remove
the three Torx bolts on each side securing the
cargo area to the chassis (see illustration).
7Make up a cradle to lift the cargo area from
the chassis, using suitable ropes or chains
attached to the tonneau tie-down points.
23Cargo area (P100 models) -
removal and refitting
22Door check arm - removal
and refitting
21Door lock - removal and
refitting
12•10Bodywork and fittings
21.17 Prising the cover plate from a cable-
operated door lock
23.6 Cargo area-to-chassis Torx bolt
locations (arrowed) - one side shown for
clarity
21.19 Disconnecting the operating cable
from a cable-operated door lock
A Removing outer cable
B Disconnecting inner cable
20.4 Door lock barrel location. Retaining
clip arrowed
Page 18 of 22
20On models with an adjustable steering
column, fully extend and lower the steering
column before attempting to remove any of
the panels on the driver’s side.
21The steering column shrouds are secured
by six screws - five through the lower shroud,
and one through the upper shroud.
22If necessary, remove the centre console.
23The driver’s side lower facia panel is
secured by five screws.
24The passenger’s side lower facia panel is
secured by eight screws.
25On models with an alarm, the alarm warning
light must be disconnected and removed before
removing the upper facia panel.
Models up to 1990
Full length console
1Where applicable, prise the electric window
switches from the front upper console panel
and disconnect the wiring.
2Remove the three securing screws from the
front upper console panel, then withdraw the
panel over the gear selector lever, at the same
time releasing the rubber gaiter where
applicable.
3On “high specification” models, where
applicable prise the electric window switches
from the rear upper console panel and
disconnect the wiring. Remove the five
securing screws and withdraw the rear upper
console panel (see illustrations).
4On “low specification” models, remove the
two securing screws and release the single
rear clip, then withdraw the rear upper
console panel.
5Where applicable, remove the two screws
securing the lower console centre bracket to
the transmission tunnel, and remove the
bracket.
6Remove the six screws securing the lower
console panel, and withdraw the panel (see
illustrations).
7Refitting is a reversal of removal.
Short console
8Prise out the blanking plug, and remove the
rear console securing screw.9On automatic transmission models, lift out
the console tray mat and remove the front two
console securing screws.
10On manual gearbox models, prise out the
blanking plugs and remove the front two
console securing screws.
11Withdraw the console over the gear
selector lever, at the same time releasing the
rubber gaiter where applicable.
Models from 1990
12Remove the switch assembly (after
disconnecting the battery negative lead), or
remove the blanking plate from the gear lever
surround, as applicable.
13Remove the securing screw from the gearlever surround, and withdraw the gear lever
surround from the console by releasing the
two securing clips.
14Remove the seven console securing
screws (see illustration).
15Chock the rear wheels, then release the
handbrake lever.
16Jack up the vehicle and support it on axle
stands (see “Jacking and Vehicle Support”).
Disconnect the handbrake equaliser from the
linkage on the underbody.
17Raise the handbrake lever fully, and lift the
console over the handbrake lever.
18Refitting is a reversal of removal, but on
completion, check the handbrake/cable
adjustment.
44Centre console - removal and
refitting
12•18Bodywork and fittings
44.3b Rear upper console panel rear
retaining screws (arrowed)
44.6b . . . centre securing screw . . .
44.14 Centre console components - models from 1990
A Screw
B Screw coverC Gear lever surround
D Blanking plateE Centre console
44.6c . . . and rear securing screw
44.6a Removing a lower console panel
front securing screw . . .44.3a Removing a rear upper console
panel front retaining screw - “high
specification” model