battery FORD SIERRA 1988 2.G Braking System Workshop Manual

Note: New seals must be used between the
reservoir and the hydraulic unit on reassembly.
Removal
1Disconnect the battery negative lead.
2Depressurise the hydraulic system by
pumping the brake pedal at least 20 times, or
until it becomes hard.
3Disconnect the wiring multi-plugs from the
reservoir cap and remove the cap.
4Unscrew the reservoir securing screw, and
remove the securing clip, noting that the clip
also supports the clutch cable (see illustration).5Prepare a suitable container to collect the
fluid as the hydraulic unit is drained, then
remove the securing spring clip and
disconnect the low pressure fluid hose from
the pump (see illustrations). Allow the fluid to
drain out of the hose into the container. If fluid
is accidentally spilt on the paintwork, wash off
immediately with cold water.
6Pull the reservoir out of the seals on the
hydraulic unit and remove it (see illustration).
7Note the spigot locating bush on the rear
hydraulic unit inlet, which may stay in the
hydraulic unit or may come out with the
reservoir (see illustration).
Refitting
8Refitting is a reversal of removal, but use
new seals between the reservoir and the
hydraulic unit.
9On completion, bleed the complete
hydraulic system and check for leaks around
all disturbed components.Note: A new gasket must be used between
the hydraulic unit and the bulkhead on
refitting.
Removal
1Disconnect the battery negative lead.
2Depressurise the hydraulic system by
pumping the brake pedal at least 20 times, or
until it becomes hard.
3Disconnect the six multi-plugs from the
hydraulic unit. They are all different, so there
is no need to label them. When a plug has a
spring clip retainer, lift the clip before pulling
out the plug. To release the pump plug, pull
back the rubber boot and the plug sleeve (see
illustrations).
4Unbolt the earth strap from the unit.
5Prepare a suitable container to catch spilt
fluid. Mark the hydraulic pipes so that they
can be refitted in their original positions, then
disconnect them from the base of the unit.
Plug the open ends of the pipes and hydraulic
unit to prevent fluid leakage and dirt ingress. If
fluid is accidentally spilt on the paintwork,
wash off immediately with cold water.
6Working inside the vehicle, remove the
lower facia panel from the driver’s side.
16Hydraulic unit (ABS)
- removal and refitting
15Fluid reservoir (ABS)
- removal and refitting
Braking system 10•15
10
15.5b . . . and disconnect the low pressure
fluid hose - ABS
16.3c . . . and the pressure switch
multi-plug - ABS16.3b . . . the main valve multi-plug . . .16.3a Disconnecting the low fluid level
switch multi-plug . . .
15.7 Removing the spigot locating bush
from the rear hydraulic unit inlet - ABS15.6 Removing the fluid reservoir from the
hydraulic unit - ABS
15.5a Remove the securing spring clip . . .15.4 Reservoir securing clip (arrowed) also
supports clutch cable - ABS
Caution: Refer to the
precautions in Section 1.
Caution: Refer to the
precautions in Section 1.

7Remove the clip from the hydraulic unit
pushrod on the brake pedal.
8With an assistant supporting the hydraulic
unit, unscrew the four nuts which secure the
unit to the bulkhead (see illustration).
Withdraw the unit from under the bonnet.
9Recover the gasket fitted between the unit
and the bulkhead.
10Drain the fluid from the reservoir. Do not
actuate the pushrod with the unit removed.
11Dismantling of the hydraulic unit should
be limited to the operations described in the
following Sections (see illustration).
Refitting
12Refitting is a reversal of removal, bearing
in mind the following points.13Do not refill the fluid reservoir until
reassembly and refitting is complete.
14Use a new gasket between the hydraulic
unit and the bulkhead.
15Ensure that the hydraulic pipes are
reconnected to the correct unions.
16On completion, bleed the complete
hydraulic system and check for leaks around
all disturbed components.
Note: A new O-ring must be used between
the accumulator and the hydraulic unit on
refitting.
Removal
1Disconnect the battery negative lead.
2Depressurise the hydraulic system by
pumping the brake pedal at least 20 times, or
until it becomes hard.
3Wrap a clean rag round the base of the
accumulator to catch any spilt fluid.
4Unscrew the accumulator using a hexagon
key. Remove the accumulator, noting the
sealing ring and being prepared for fluid
spillage (see illustration). If fluid isaccidentally spilt on the paintwork, wash off
immediately with cold water.
Refitting
5Fit a new O-ring to the base of the
accumulator, fit the accumulator and tighten
it.
6Reconnect the battery. Switch on the
ignition and check that the hydraulic unit
pump stops within 60 seconds; if not, the
accumulator is likely to be faulty.
7On completion, bleed the complete
hydraulic system and check for leaks around
all disturbed components.
Note: New sealing washers must be used on
the high pressure fluid hose banjo union, and
a new O-ring must be used between the
accumulator and the hydraulic unit on refitting.
Removal
1Remove the accumulator.
2Prepare a suitable container to catch spilt
fluid, and disconnect the high pressure fluid
hose from the pump.
3Remove the securing spring clip and
disconnect the low pressure fluid hose from
the pump. Allow the fluid to drain out of the
hose into the container. If fluid is accidentally
spilt on the paintwork, wash off immediately
with cold water.
4Disconnect the multi-plugs from the
pressure switch and the pump motor.
5Remove the pump mounting bolt (see
illustration).
6Pull the pump and motor assembly off the
mounting spigot and remove it.
7Recover the mounting bushes and renew
them if necessary.
8If a new pump is to be fitted, transfer the
pressure switch to it, using a new O-ring.
18Hydraulic unit pump and motor
(ABS) - removal and refitting
17Hydraulic unit accumulator
(ABS) - removal and refitting
10•16Braking system
16.8 Hydraulic unit-to-bulkhead securing
nuts (arrowed) - ABS
17.4 Unscrew the accumulator and remove
it, noting the O-ring (arrowed)
16.11 Hydraulic unit components - ABS
A Fluid reservoir
B Accumulator
C Main valveD Master cylinder
E Pushrod
F Pump and motorG Booster
H Pressure switch
J Valve block
Caution: Refer to the
precautions in Section 1.
Caution: Refer to the
precautions in Section 1.

Refitting
9Commence refitting by offering the pump to
the mounting spigot, then reconnecting the
low pressure fluid hose.
10Refit and tighten the pump mounting bolt.
11Reconnect the high pressure fluid hose,
using new sealing washers on the banjo
union.
12Refit the accumulator, using a new O-ring.
13Reconnect the multi-plugs and the
battery.
14Refill the fluid reservoir, then switch on the
ignition and allow the pump to prime itself.
Allow the pump to run for a maximum of two
minutes at a time then leave it for ten minutes
to cool down.
15On completion, bleed the complete
hydraulic system and check for leaks around
all disturbed components.
Note: To remove the pressure switch from the
hydraulic unit in situ, Ford tool No 12-008 or a
locally made equivalent will be required. The
switch may be removed without special tools
after removing the hydraulic unit complete or
the pump above. A new O-ring must be used
when refitting the switch.
Removal
1Disconnect the battery negative lead.
2Depressurise the hydraulic system by
pumping the brake pedal at least 20 times, or
until it becomes hard.
3Disconnect the multi-plug from the switch,
then unscrew and remove the switch.
Refitting
4Refit the switch using a new O-ring.
Position the plastic sleeve so that the drain
hole faces the pump motor, then tighten the
switch (see illustration).
5Reconnect the multi-plug and the battery.
6On completion, bleed the complete
hydraulic system and check for leaks around
all disturbed components.
Removal
1Disconnect the battery negative lead.
2Depressurise the hydraulic system by
pumping the brake pedal at least 20 times, or
until it becomes hard.
3Apply the handbrake, and slacken the
left-hand front wheel nuts. Jack up the front of
the vehicle and support on axle stands (see
“Jacking and Vehicle Support”).Remove the
left-hand front wheel.
4Remove the plastic liner from under the
wheel arch.
5Prepare a suitable container to catch spilt
fluid, clean around the unions on the valve
block, then unscrew and disconnect the fluid
pipes (see illustration). Plug the open ends of
the pipes and valve block to prevent fluid
leakage and dirt ingress. If fluid is accidentally
spilt on the paintwork, wash off immediately
with cold water.
6Disconnect the multi-plug and the earth
strap from the valve block.
7Working through the wheel arch, unscrew
the three nuts which secure the valve block
mounting bracket (see illustration).8Remove the valve block and mounting
bracket, taking care not to spill brake fluid on
the paintwork.
9No further dismantling of the valve block is
possible, but the pressure regulating valve in
the rear brake pipe union can be renewed if
desired.
Refitting
10Refitting is a reversal of removal.
11On completion, bleed the complete
hydraulic system and check for leaks around
all disturbed components.
Removal
1Disconnect the battery.
2Working inside the vehicle, prise out the
facia trim panel from the passenger’s side.
Remove the insulation.
3To remove the now exposed module, push
it as necessary to release the retaining catch.
21Computer module (ABS)
- removal and refitting
20Valve block (ABS) -removal
andrefitting
19Hydraulic unit pressure switch
(ABS) - removal and refitting
Braking system 10•17
10
20.5 Valve block and associated
components - ABS
A Bracket screws
B Adapter plate
C valve blockD Multi-plug
E Earth strap
anchor point
19.4 Refit the pressure switch with the
drain hole (arrowed) in the plastic sleeve
facing the pump motor - ABS18.5 Hydraulic unit pump mounting bolt -
ABS
20.7 Unscrewing the valve block mounting
bracket nuts (arrowed) - ABS
Caution: Refer to the
precautions in Section 1.
Caution: Refer to the
precautions in Section 1.

Removal
1Chock the rear wheels, jack up the front of
the vehicle and support on axle stands.
Release the handbrake. Disconnect the
battery negative lead.
2Slacken the handbrake cable adjuster.
3Extract the securing circlip and pivot pin,
and detach the handbrake equaliser from the
linkage on the underbody (see illustration).
4Working inside the vehicle, remove the
handbrake lever rubber gaiter and/or the
centre console, as necessary.
5Disconnect the wiring connector from the
handbrake “on” warning switch. 6Unscrew the two handbrake lever mounting
bolts, and carefully lift the lever through the
underfloor gaiter.
7If required, the handbrake “on” warning
switch can be removed.Refitting
8Refitting is a reversal of removal, but on
completion, adjust the handbrake cable.
Removal
1Remove the clutch pedal as described in
Chapter 6.
2Extract the inboard circlip from the brake
pedal end of the pivot shaft (see illustration).3The brake pedal can now be removed from
the pedal bracket by sliding out the pivot
shaft, noting the position of any washers and
spacers which may be fitted.
4If desired, the nylon bushes can be prised
from each side of the pedal for renewal, and
the brake lamp switch removed.
Refitting
5Refitting is a reversal of removal, fitting any
washers and spacers in their original
positions. Refit the clutch pedal.
30Brake pedal - removal and
refitting
29Handbrake lever -removal
andrefitting
10•22Braking system
29.3 Handbrake equaliser and linkage on underbody30.2 Extract the inboard circlip (arrowed) to remove the pedal
pivot shaft