FORD SIERRA 1988 2.G Cooling And Air Conditioning Systems Workshop Manual

FORD SIERRA 1988 2.G Cooling And Air Conditioning Systems Workshop Manual SIERRA 1988 2.G FORD FORD https://www.carmanualsonline.info/img/11/5453/w960_5453-0.png FORD SIERRA 1988 2.G Cooling And Air Conditioning Systems Workshop Manual
Trending: bulb, washer fluid, jacking, fuel, transmission oil, heating, drain bolt

Page 1 of 12

FORD SIERRA 1988 2.G Cooling And Air Conditioning Systems Workshop Manual System type
SOHC models  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pressurised, with belt-driven coolant pump, crossflow radiator,
thermo-viscous fan, t

Page 2 of 12

FORD SIERRA 1988 2.G Cooling And Air Conditioning Systems Workshop Manual Torque wrench settingsNmlbf ft
Radiator upper mounting nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 to 2515 to 18
Radiator lower mounting bolts . . . . . . . . . . . . . . .

Page 3 of 12

FORD SIERRA 1988 2.G Cooling And Air Conditioning Systems Workshop Manual passing over the evaporator fins on its way to
the vehicle interior. The refrigerant becomes a
gas again and the cycle is repeated.
Various subsidiary controls and sensors
protect the system against e

Page 4 of 12

FORD SIERRA 1988 2.G Cooling And Air Conditioning Systems Workshop Manual 3A radiator specialist can perform a “flow
test” on the radiator to establish whether an
internal blockage exists.
4A leaking radiator must be referred to a
specialist for permanent repair. Do not

Page 5 of 12

FORD SIERRA 1988 2.G Cooling And Air Conditioning Systems Workshop Manual 17Note that the thermostat wax capsule
must face into the inlet manifold, with the flow
direction arrow pointing forward, in line with
the pressure relief valve in the housing (see
illustration). 
18R

Page 6 of 12

FORD SIERRA 1988 2.G Cooling And Air Conditioning Systems Workshop Manual 8Unscrew the three retaining bolts and
remove the coolant pump and gasket from the
front of the cylinder block. Note that on
certain models, the alternator adjusting link is
secured by the right-hand

Page 7 of 12

FORD SIERRA 1988 2.G Cooling And Air Conditioning Systems Workshop Manual 36Tighten the coolant pump securing bolts,
and where applicable the pump pulley
securing bolts, to the specified torque. 
37On completion, refill the cooling system.
Refer to Chapter 1, Section 21.
Re

Page 8 of 12

FORD SIERRA 1988 2.G Cooling And Air Conditioning Systems Workshop Manual DOHC models
6Disconnect the battery negative lead.
7To provide additional clearance when
removing the cooling fan shroud assembly
(which is removed from below the vehicle),
apply the handbrake, then j

Page 9 of 12

FORD SIERRA 1988 2.G Cooling And Air Conditioning Systems Workshop Manual 2With the engine cold, slowly unscrew the
expansion tank cap to release any remaining
pressure from the cooling system, then refit
the cap.
3Disconnect the wiring from the sender
terminal (see illustr

Page 10 of 12

FORD SIERRA 1988 2.G Cooling And Air Conditioning Systems Workshop Manual 1With the heater unit removed from the
vehicle, remove the two securing screws and
withdraw the heater matrix from the casing
(see illustrations).
2Cut the heater casing gasket in line with the
casing
Page:   1-10 11-20 next >
Trending: coolant, alternator belt, automatic transmission, tow, drain bolt, fuel, jacking