oil type FORD SIERRA 1989 2.G XR4 Workshop Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1989, Model line: SIERRA, Model: FORD SIERRA 1989 2.GPages: 45, PDF Size: 1.33 MB
Page 3 of 45
pC pB
pD pJ
pK
pE
pJ
pG
pI
pF
pH
Suspension - (front)0 2
pA
sway bar bushings
(see page 4)
pF Front Control Arms higher mileage cars exhibiting ball
joint and bushing wear can benefit from our standard control
arms. These arms are brand new, and include ball joints and
bushings installed.
Note: the outboard (sway/control arm) bushing
is an uprated "castellated" design which transmits less vibration
than the original U.S. spec. bushing.
(left) M428L
(right) M428R
pG
Inner Control Arm Bushing H.D. Made from
increased durometer rubber, these heavy duty (GPN) bushings
offer the desired firming effect while retaining a reasonable
degree of shock and vibration absorption. (each) M428BH-N
Optional urethane version of above bushing(set) M428BU
pH
Control Arm/Sway Bar Bushing Kit This heavy
duty urethane bushing set really does an excellent job
limiting the amount of "jutter" felt at the steering wheel
which is especially noticeable under braking. The kit includes
bushing halves and center sleeves to do both sides of the
car and is easy to install.
(set) M428BK
pH
Control Arm/Sway Bar Bushings As an option to
urethane bushings we offer either the "castellated" type
outer TCA bushings are available in standard rubber, or the
new style (better fills the void between the bushing halves)
H.D. GPN bushing kit. Both will dramatically reduce the
vibration under braking common to XR's and Scorpio's.
Outer TCA Bushings Standard (pair) does 1 armM428B
Outer TCA Bushing Set H.D. (set)M428BK-N
pI
Sway Bar Washer Get the most from your new
"castellated" type outer TCA bushings by using this "shallow"
washer (in front behind the lock nut) for a tighter fit.M407W
pJ
Tie Rod Ends High quality European Ford standard
replacement tie rod ends. (left) M434L (right) M434R
pK
Front Strut Upper Insulator H.D. Made from increased
durometer rubber, these heavy duty (GPN) Insulators offer the
desired firming effect while retaining a reasonable degree of
shock and vibration absorption. Steering and transitional
response becomes noticeably more direct.(each) M404 pA
Front Sway Bar The larger Cosworth Sierra 28.5mm
factory front sway bar is a direct replacement for the standard
25mm bar.
(H.D. bar clamp bushings are included)M407
NOTE: see price list for sway bar clamp bushings for XR & Scorpio
pB Spring Sets see page 3 (spring section) for listings
pC Front Struts (see below- shocks sold as each)
Spax TA series struts utilize a non pressurized gas over oil design
with 10 positive settings (knob type external adjustment on top) for
tuning the dampening to suit individual applications.M401A
Spax Sport One of the most popular shocks we sell, Spax fixed rate
gas sport shocks are an excellent choice for upgrading the handling
performance on the XR. M401V
Bilstein New for 2000. Bilstein's new sprint series gas shocks
offer the big B's renowned German made performance at a very
attractive price. Bilstein shocks are now available in our
suspension kits see page 3 for details.M401B
Rally/Sport Super-Gas made to European Ford spec. by Koni of
Holland. R/S shocks feature Konis twin-tube low pressure design and
have adjustable settings (knob type external adjustment on top) which
can be tailored to suit individual applications.
M401RS
Boge Turbo-Gas German manufactured twin tube high pressure
gas design utilizing a unique variable valving system that insures
the perfect balance between ride comfort and road holding
capability.M401S
DeCarbon French made mono tube high pressure gas shocks with
fairly sporty valving, similar in design to Bilstein.M401G
KYB GR2 gas struts are high quality, heavy duty units that are
a cost effective performance upgrade for the XR4. Handling is
improved without sacrificing ride quality.M401Y
pD
Steering Rack complete rack assembly w/inner tie rods,
boots, and stainless steel inner sleeve. M434SR
pE
Rack Boot* replacement steering rack boot M434RB
*same boot left or right XR4 & Scorpio
Shock Absorbers
GAS SHOCK ABSORBERSSUPER
GAS SHOCK ABSORBERScheck price lists for Scorpio versions of listed items check price lists for Scorpio versions of listed itemscheck price lists for Scorpio versions of listed items check price lists for Scorpio versions of listed items
check price lists for Scorpio versions of listed items
Page 11 of 45
Brake (related)
pA
pEpA
Racing Brake Fluid Not all brake fluid is created equally. High
operating temperatures at the caliper transfers extreme heat through the piston
causing lesser quality brake fluid to boil. This in turn allows the fluid to become
compressed and reduces overall braking performance. The best way to
counter this from happening is to use a racing specification, mineral (never
synthetic) brake fluid and flush the system after each event for competition or
annually on performance street driven vehicles. Both AP550 and Wilwood 570
brake fluid is DOT approved with a dry boiling point of 550-570 degrees, low
viscosity minimizes aeration and permits easy bleeding.
Brake Fluid AP Competition (16.9oz. 500ml.) MC550
Brake Fluid Wilwood 570 (12oz. 355ml.) MC570
Brake Fluid Wilwood 570 (6 Pack) MC57-6
Brake Fluid Wilwood 570 (24 Case) MC57-C
pB
Cosworth & Scorpio Rotors For those fortunate few who own
Cosworth Sierras or have converted XR4's to Cosworth type front or rear brakes
and are in need of replacement rotors we have them. Scorpio front or rear rotors
in standard and cross drilled are also available. (see price list page 31)
Cosworth Front 283 x 24mm standard, X-drilled, grooved
Cosworth Rear 273 x 10mm standard, X-drilled, grooved
Scorpio Front 260 x 24mm standard or X-drilled
Scorpio Rear 253 x 10mm standard or X-drilled
Performance Brake Kits Engineered competition brake kits for the
ultimate in stopping power.
pC Front R/S Brake Kit (283 x 24mm)
BAT R/S "big brake" kit allows larger 11.25" (285mm) brake rotors to be fitted
with standard XR calipers. Increasing rotor "swept area" in this way will greatly
improve stopping power (leverage) and help to reduce high brake temperatures
that can cause premature brake fade and poor pedal feel.
Kit includes:
285 x 24mm vented (standard or cross-drilled) rotors, Mintex 1144 brake pad
set, caliper mounting brackets & hardware (fitment with most 15" wheels -
some require slight modification)
kit supplied with standard rotors
M418
kit supplied with cross drilled rotors M418A
pD Front Brake Kit (283 x 24mm) w/4 Piston Calipers
Combine the performance of the R/S large rotor kit with 4 piston calipers for the
ultimate in stopping power.
includes: 283 x 24mm vented rotors,
4-piston alloy Wilwood Superlite 2A calipers with pads. (fitment with most 15"
wheels -some require modification or spacers)
M416W
pD Front Brake Kit (300 x 32mm) w/4 Piston Calipers
For those who are looking for the ultimate brake performance. Quite simply the
largest and most competent competition type brake kit that can be fitted to the XR4.
includes: 300 x 32mm vented rotors with light alloy hats, 4-piston alloy Wilwood
Superlite IIA calipers, caliper mounting brackets & hardware
M417A
(this kit also available for Scorpio ! ) G417A
Rear Kit (XR4 w/16" wheels) 300 x 21mm (See Price List)
includes: 300 x 21mm vented rotors with light alloy hats, 4-piston alloy Wilwood
Superlite 2A calipers, caliper mounting brackets & hardware
pE Wheel Bearings Genuine European Ford wheel bearing kits are
complete with all required service parts to do a first class job. Each kit
include bearings, races, seals and hub nuts to service one wheel.
Front Wheel Bearing Kit (specify left or right) -XR4 M560F
Rear Wheel Bearing Kit (specify left or right) -XR4 M560R
Front Wheel Bearing Kit (specify left or right) -Scorpio G560F
Rear Wheel Bearing Kit (specify left or right) -Scorpio G560R
pB
pC
pD
1 0
Page 14 of 45
pA Replica Cosworth Body Components
Fiberglass body panels are an alternative to the more expensive, and
becoming unavailable, factory Ford versions. We have searched far and wide
to import only the highest quality fiberglass replica bodywork. Even so,
fiberglass is more prone to incidental damage (cracking) than the more
flexible ABS plastic or urethane original Ford components. Also keep in mind
that fitting is totally DIY and most items will require paint prep work, fabricated
brackets and other hardware.
Important Note: We often hear horror stories
from customers who have ordered similar fiberglass items from European
mail-order suppliers only to receive broken or substandard components, and
now you own it! Worse yet, the shipping costs involved importing large, bulky,
items like these can far exceed the cost of the part, and what started out as
a bargain now has become a expensive learning experience. Our pricing on
all items, including sheet metal & body panels,
includes inbound freight from
Europe. Once here, some items that are too large for UPS (or other carriers)
will be shipped truck freight collect, we will also extend our 25% C.F. Motor
Freight discount.
Front Spoiler Bumper (R/S Cosworth type) M353F
Front Spoiler Bumper (R/S 500 Type) with lower "splitters*" M353FA
*lower chin spoiler moulded in on lower edge
Rear Bumper (R/S Cosworth type)
Rear Wing Airfoil (R/S Cosworth type)
see information belowM306F
Rear Wing Airfoil (R/S 500 type) M306FA
Lower Rear Wing (R/S 500 type) M306L
Cosworth Wheel Arches (4) & Side Skirts (2)
see information belowM302F
Cosworth Hood (complete with vent louvers)
Hood Vent Louvers (2)
fiberglass (functional)M814F
Hood Vent Louvers (2)
stick-on ABS plastic (non functional)M814FS
pB
Cosworth Sierra Arches & Skirt
Sadly the factory Ford wheel arches have recently become unavaiable. Some
side skirts still remain but for the most part the R/S arches and skirts have gone
the way of all the factory R/S 500 stuff "not availabe- not replaced". In place
of the origionals we can offer a reasonable cost & quality fiberglass alternative
wheel arch and side skirt kit. For anyone searching out new factory arches and
skirts we might still have a couple odd arches & skirts available (no full sets)
call for more information & pricing.
Cosworth Wheel Arches (4) & Side Skirts (2)-
fiberglassM302F
pC
Cosworth Rear Airfoil
One of the trademarks of the Cosworth Sierra is its large rear wing/airfoil.
Perhaps a bit gaudy for some tastes, none the less it does a great job at
keeping the rear end planted. At speeds over 100mph as much as 45 lbs. of
downforce is created for added high speed stability. Anyone interested in this
item had one of two choices. The factory Ford Cosworth rear wing/airfoil (still
available from Ford Europe) but at over $1800.00 who can afford it. Or the
usual aftermarket fiberglass versions, although much cheaper in cost the
quality suffers greatly. When we sampled most of these we were genuinely
concerned that some of the replica wings might come apart, or even fly off at
speed ! This dilemma prompted us to undertake manufacturing a super high
quality fiberglass replica that solves all the above problems. It is extremely
well built, can be securely attached to the car and is attractively priced.
Note:
rear wings are designed to fit smaller hatch 1985-87 cars- the mounting foot
will overhang on the hatch glass molding on later cars and will have to be trimmed.
Rear Wing Airfoil (R/S Cosworth type) M306F
see above section for larger RS500 version
pC
pB pA
Bodywork
(See Price List) (See Price List)
1 3
Page 18 of 45
Accessories
pA Scorpio R/S Rear Wing This hot looking rear wing goes a long way
in transforming Scorpio's look. For installation R/S wings will require
painting to match your cars color, and some mounting holes from the
standard spoiler will need to be filled and spot painted. Also note that a rear
brake light will need to be located elsewhere in the rear window.G306
Scorpio R/S Side Skirts Matching Rally Sport rocker panel side skirt
set looks great with above rear wing or without. Other than just good
looks, side skirts help to keep the door sides and rockers cleaner and with
less stone chips. Easy to fit, paint and install.G302S
pB Scorpio Cowl Cover What is it, and why doesn't my car have one?
This is a commonly asked question regarding this item. Ford equipped
very few Scorpios bound for the US market with these European cowl
covers. This moulded plastic cover keeps dirt, debris and small animals
from winding up in the ventilation fan and associated duct work. Clean
out this area once and for all, then install a new cowl cover- your Scorpio
will thank you.G369C
pC Mini-Lite Wheels (15" x 7") for XR4 Cars of English heritage,
XR4's included, look great on classic Mini-Lite type wheels. These
wheels are both lightweight and attractive with a bright silver clear coat
finish. Specifications: 4 x 108mm pattern, 15" x 7" size, 38mm offset,
18lbs each, center caps included.M411M
pD Thrust Wheels (15" x 7") for XR4 We are often asked to supply
inexpensive road wheels, and here they are. The Thrust is a 10 spoke
light alloy wheel with locking center cover, available in either silver, or
charcoal w/silver lip. You will not find a better quality, proper wheel
fitment for the price. Specifications: 4 x 108mm pattern, 15" x 7" size,
35mm offset, 18lbs each, locking center covers included.M411T
pE Floor Mats Foul weather mats, commonly referred to as "ice cube
trays" or "waffle mats", are made of heavy duty rubber with small
compartments to catch melting ice, water, mud etc. from your shoes or
boots. These Euro. Ford mats are the best protection for your interior for the
winter months or when going afield. Can be placed over standard plush
mats or directly on carpeting. When dirty or filled with water- remove, drain,
hose off, and reinstall. Front mats will fit both XR4 and Scorpio, rear mats
are for XR4 only.
Front Mat set M1010 Rear Mat SetM1011
First Aid Kits We are often asked to supply the First Aid kits that Ford
equips new cars with in Europe. Includes more than just a selection of
"Band-Aids". Think of it as good insurance.M102
Fuse Box Covers A common breakage item on XR4's. We have new
European Ford replacements.M474
pF Sunroof Wind Deflector The buffeting effect, and wind noise, that
takes place with the sunroof open at speed can be eliminated with a
Sunroof Wind Deflector. Tinted smoke (grey) acrylic, fits both XR4 and
Scorpio- hardware included.M307
pG Side Window Wind Deflector for XR4 A similar product to the
Sunroof Deflector the Side Window Deflector keeps the wind noise levels
to a minimum while allowing maximum ventilation. Effective even in light
rain! Tinted smoke (grey) acrylic, easy installation- no holes to drill. For
XR4 only- sold in pairs.M340WD
pB
pD
pC
pA
pE
pG pF
1 7
Page 22 of 45
pJ
pI
pM
pK
pV
pU
continuation
pV
pG
pH
pE
pC pB
pA
pL
pP
pF
pN
pQ
pD
pO
The cooling system on the XR4Ti is fairly unique. If there is
another car with more individual hoses in the cooling system,
we have yet to see it. Compound this with the changes
throughout the model run and it gets even more complex. We
have a good inventory of the hoses and other cooling related
components that fit 1985-87 XR4Ti and some (where similar
or noted) for 88-1989 cars.
pA
Hose- heater valve to pipe (leads to oil cooler) M421HC
pB
Hose- heater valve to heater coreM421H
(note: pB interchanges with pJ)
pC Hose- heater valve to pipe along valve cover (upper)
at rear
(note: pC interchanges with pF )M421HB
pD
Heater Valve- heater control valve XR & Scorpio M421V
pE
Hose- water pipe (lower) to oil coolerM421HE
pF
Hose- oil cooler to water pipe (from heat valve)M421HB
(note: pF interchanges with pC )
pG Hose- oil cooler to intake manifoldM421HD
pH
Oil Cooler- replacement water to oil heat exchangerAWC1
pI Hose- pipe along valve cover (lower) @ front to water
pump. This one is a common problem.M421HA
pJ
Hose- pipe along valve cover (upper) @ front to thermostat
housing (heater supply). Don't hit the road without an extra one
of these!
(note: pJ interchanges with pB )M421H
pK
Water Pump- quality replacement pump L6A
pK1
Thermostat Housing- H.D. cast Iron version L2F
pL
Hose- radiator (lower) 1985-88 (MT & AT)M421BH
pL
Hose- radiator (lower) 1989 (auto & manual)M421BH9
pM
Hose- radiator (upper) 1985-88 (MT & AT)M421TH
pM
Hose- radiator (upper) 1989 (MT & AT) M421TH9
pS
pK1
Cooling System (XR)
pW
Plumbing Schematic
1985-88 XR4Ti w/5 speed
pTpR
pN Hose- expansion tank (top fitting) to valve cover pipe
(note: shape of hose not accurate in drawing)M421TT
pO
Expansion Tank- Thread-on cap (similar to Scorpio) Ford
tanks, some with, or without, the fluid level sensor port. Tank
caps, fluid level sensors, and sensor mounting parts are also
available. (see price list for complete listing)
Tank 1985-88 M421E Tank 1989 w/o sensor M421E9
pP
Hose- expansion tank (lower fitting) to radiator drain line
M421TL
pQ
Hose- expansion tank (middle fitting) to radiator (upper)
M421TM
pR
Radiator- O.E. type replacement radiators for 1985-89 manual
or 1985-88 auto transmission XR4Ti's.
(1985-88 manual) M421R (1985-88 auto) M421RA
(1989 manual) M421R9 (1989 auto) M421R9A
Mount/Bushing- @ radiator top mounting locationM421RM
pS
Electric Fan- An altermative to the sometimes troublesome
dual cooling fans on the XR4Ti, this highly efficent (1100 cfm) 16"
electric "puller" fan does the work of both. Wire directly or use our
(optional) adjustable 165-215 degree thermostat/relay pack.
(16" puller fan) A16F-PL (thermo/relay) AFTR1
pT
Blower Motor & Fan A/C & Heater -for heater and A/C,
check fuse & relay first before ordering. M470A
pU
Heater Core- New O.E. Ford heater cores. M471
pV
Turbo Water Hose -high temperature CPE silicone hose for
turbo (water) inlet/outlet pipes. (1 foot makes 3 hoses)
M421WT
pW
Hose- Lower drain pipe @ radiator lower M421HF
2 1
Page 23 of 45
pA
pB
pC
pD
pE
pF
pG
pH pJ
pK
pL
pP
pIpN
pOpM
pS
pR pQ
Cooling System (Scorpio)
In addition to our stock of cooling system components for the XR4Ti
we have added the various Scorpio related items to our inventory.
The Scorpio's cooling system is only slightly less complicated than
the XR4Ti's, it's only saving grace is the parts do not vary all that
much from year to year. Again, as with the XR4, components that
we offer are from the O.E. supplier or Ford originals.
pA Hose*- heater valve (outlet) to heater core G421HA
pB
Hose*- heater valve to engine/inlet mfld.G421HB
pC
Hose*- heater valve (inlet) to heater coreG421HC
pD
Hose*- heater valve to pipeG421HD
*for additional info see (diagram A) on page 20
pE Radiator- new original equipment Ford radiators at a very
attractive prices. Don't be mislead into buying substandard
fabricated or fits-all radiators when we can supply new Ford ones
for less.
(for automatic trans)G421RA
(for manual trans.)G421R
pF
Hose- coolant tank to thermostat housingG421HF
pG
Hose- top radiator hose (88-89)G421TH
pG
Hose*- top radiator hose (89 late) has vent air bleed in line
(includes bleed screw).G421TH-9
*for additional info see (diagram B) on page 20
pH Hose- tank (lower) to water pumpG421HH
pI
Water Pump- new Ford water pumpG421
pI
Water Pump- high quality reconditioned water pump on
Ford core.G421A
Hose*- bypass from water pump to inlet mfld.G421HP
*for additional info see (diagram A) on page 20
pJ Hose- lower radiator hose 88-89G421BH
pJ
Hose*- lower radiator hose (89 late) has additional tee off
hose running to overflow tank @ lower bungG421BH-9
*for additional info see (diagram B) on page 20
pK Hose*- to oil cooler pipeG421HK
pL
Hose*- oil cooler pipe to oil coolerG421HL
*for additional info see (diagram A) on page 20
pM Coolant Tank- Cracked and leaking overflow tanks are a
common problem on the Scorpio. Tank pictured above is for early
(1988) type cars.
See page 20 for late style tanks.G421TE
pN
Radiator Cap- cap for Scorpio and XR4's with thread-on
coolant tankG421C
pO
Oil Cooler- replacement water to oil heat exchanger.
If water is showing up in your oil it would most likely be either a head
gasket or one of these.AD1000
pP Heater Control Valve- heater control valve, same on
XR4 & ScorpioM421V
pQ
Heater Core- Quality Ford O.E. heater cores.G471
pR
Mechanical Fan Clutch- Quality Ford O.E.G422
pR
Electric Fan- An altermative to the Scorpio mechanical
clutch fan. This highly efficent (1150 cfm) 16" electric "puller" fan
moves more air and frees up a few HP to boot. Wire directly or use
our (optional) adjustable 165-215 degree thermostat/relay wiring kit.
(16" electric fan) A16F-PL
(thermo/relay wiring kit) AFTR1
pS
Heater A/C Blower Motor- New Ford heater blower motor
for Scorpio with 8 wire harness/plug.
G470H
see (diagram A) on page 20
2 2
Page 24 of 45
Cooling System (Scorpio) supplement
pA
pF
pHpJ
Diagram A - heater and oil cooling water system
Scorpio 1988-89 (all)
pA
Hose*- heater valve (outlet) to heater coreG421HA
pB
Hose- heater valve to engine/inlet mfld.G421HB
pC
Hose*- heater valve (inlet) to heater coreG421HC
pD
Hose*- heater valve to oil cooler pipeG421HD
pE
Heater Control Valve*- heater control valve, same on
XR4 & ScorpioM421V
pF
Hose- connects coolant pipe from heater control valve
to oil cooler.G421HL
pG
Oil Cooler*- replacement water to oil heat exchanger.
If water is showing up in your oil it would most likely be either a
head gasket or one of these.AWC1
pH Hose*- oil cooler to coolant pipe.G421HM
pI
Hose*- connects coolant pipe from oil cooler to water
pump.G421HK
pJ
Hose- bypass from water pump to inlet mfld.G421HP
*these items are also shown on page 19 diagram
Diagram B- Components unique to late 89 Scorpio
Scorpio 89 (late)
pK
Hose*- top radiator hoseG421TH
*hose with vent is no longer avalable
pL Hose- coolant tank to thermostat housingG421HF-9
pM
Tank Level Sender- sender/float assembly. Fits all
Scorpio & XR4 over flow tanks.M421LS
pN
Sender Install Kit- the 3 components (threaded collar,
spacer ring, rubber gromett) required to stop a leaking
sensor bung. Also a good idea when servicing the tank level
sensor (see above part).M421SK
pO
Cap/Plug- small rubber cap for plugging off the unused
waterpump port .G421P
pP
Hose- lower radiator hose (89 late) has additional tee off
hose running to overflow tank @ lower bungG421BH-9
pQ
Coolant Tank- oval type tank (use G421TL below)
pR Coolant Tank- late style (1990-92) coolant tank.
Rectangular (larger volume) tank is a direct fit upgrade to the
oval version listed above.G421TL
pS
Radiator Cap- cap for Scorpio and XR4's with thread-
on coolant tankG421C
pK
pM
pN
pO
pPpQpR
see page 19
for radiators
see page 19
for water pump
Diagram B
pC
pDpB pE
pG
pS pLpS
Diagram A
pI
2 3
Page 28 of 45
Engine & Related Items
2.5mm metallic inductance EMI
suppressed conductor: with
stainless steel windings spaced
over ferrimagnetic core
substrate
serves as
strength
member for
cable assembly
ignition cables have a non-layered high strenght insulating
jacket made entirely of aerospace grade silicone rubber to
prevent swelling and splitting at extreme trmperatures
KV85 & R-100
metallic inductance EMI
suppressed conductor
pA Performance Air Filters A quick and easy performance modification
is to replace the standard air filter with a direct fit KN high performance air filter.
Merkur XR4Ti (2.3L Turbo)M22P
Merkur Scorpio (2.9L V-6)G22P
pB
High Temp Fyre Sleeve The under hood temperatures on the XR4Ti can
be quite severe. Slipping a length of fyre sleeve over critical wiring or rubber water
& A/C hoses will add an extra degree of protection. Fyre Sleeve provides radiant heat
protection up to 800 degrees. Sleeve is sold per foot and is sized by internal diameter.
Hoses or wiring can be disconnected at one or both ends then slipped through fyre
sleeve or sleeve can be un-stitched at the seam and wire tied in place.
Mylar Fyre Foil Sleeve -10 (7/8" I.D.) per foot320510
Mylar Fyre Foil Sleeve -12 (1" I.D.) per foot320512
Mylar Fyre Foil Sleeve -16 (1 1/4" I.D.) per foot320516
Mylar Fyre Foil Sleeve -20 (1 1/2" I.D.) per foot320520
pC
Engine Mount Insulators BAT has an alternative to the recently
discontinued original equipment Ford motor mounts on the XR4Ti. Simply
remove the old motor mount assemblies, discard the worn-out rubber
portion, and reuse the top and bottom metal plates with our replacement
insulators.
Note: slight modification requires 10mm holes in plates to be
increased to 12mm. Scorpio mounts are Ford mfg. direct replacements.
Engine Mount Insulator (left & right same) XR4TiM433
Engine Mount Insulator (left & right same) Scorpio-
new FordG433
pD
Transmission Mount /Insulator Rear transmission mount/insulator-
direct fit for automatic & manual Scorpio. A heavy duty version also available.
Note:
this "square" type mount can be fitted to the XR4 with special crossmember, (see
below) as the standard "round" trans. mount used on our XR4Ti's is no longer available.
Transmission Mount Insulator*- (automatic & manual) G433T
Transmission Mount Insulator H.D*.- (automatic & manual) M433TA
*can be fitted to XR4 with additional x-member (see below)
pE Transmission Crossmember Wide and narrow type transmission
tunnel crossmenbers allow the above "square" mount/insulators to be installed in
the XR4Ti. Fitting the XR with this crossmember/mount combination is a consider-
able upgrade (strength, noise, vibration) over the USA supplied "round" mount.
Crossmember* XR4 (wide) 1987-89- manual & auto M433XL
Crossmember* XR4 (narrow) 1985-86- manual & autoM433X
*for use in combination with above G433, M433 "square" type mount
pF Engine Belts H.D. Our search for the ultimate heavy duty engine
accessory v-belts lead us to the top cog "Gold Series" by Dayco. Top cog v-
belts are built to last up to 20% longer than conventional belts. A unique cogged
design increases flexibility and airflow around the belt for reduced friction and
heat. Laminated design with high temperature rated polyester cords provide
maximum tension holding (reduced slip) over the life of the belt.
Belt- XR4Ti (1985-89) W. Pump, Alt, P. Steering (2 required)M6G
Belt- XR4Ti (1986-89) A/C CompressorM6H
Belt- XR4Ti (1985) A/C CompressorM6HA
Belt- Scorpio (1988-89) Fan & Power Steering (2 required)G6G
Belt- Scorpio (1988-89) AlternatorG6GA
Belt- Scorpio (1988-89) A/C CompressorG6H
pG
Performance Ignition Wire Sets We have tried a number of
different ignition wire options on the 2.3 Turbo and 2.9L V6 engines and have
found the Magnecor brand to offer superior quality, performance, and durability.
Cables are red in color with 8mm, 8.5mm and 10mm cable diameters.
Merkur XR4Ti (2.3L Turbo)
Ignition Wire Set- (8mm w/silicone jacket and boots)L9HT
Ignition Wire Set- (8.5mm KV85 wire w/silicone jacket and boots)M9HT
Ignition Wire Set- (10mm R-100 wire w/silicone jacket and boots)M9HTR
Merkur Scorpio (2.9L V6)
Ignition Wire Set- (8mm w/silicone jacket and boots)G9HT
Ignition Wire Set- (8.5mm KV85 wire w/silicone jacket and boots)G9HT9 pG
pF
pA
Aluminized Mylar Fyre Sleeve
pB
pC pD
pE
2 7
Page 29 of 45
L4-218
L2G L4ES
L15D
L15DS
L604A
L15E
L2KS L4FS
2300 Turbo Engine Components
Cylinder Block Bare (H.D. "Turbo" Block) L2G 475.00
Main Cap Stud Set (H.D. ARP) L2KS 94.55
Full Gasket Set (Felpro)
1985 engineL15AA 95.00
Full Gasket Set (Felpro)
1986-89 engineL15AB 124.50
Top End Gasket Set (Felpro)
specify year when orderingL15BA 55.00
Top End Gasket Set (Felpro)
with hi-temp valve cover setL15BB 79.50
Bottom End Gasket Set (Felpro)
1985 engine (cork pan)L15CA 40.10
Bottom End Gasket Set (Felpro)
1986-89 engine (rubber pan)L15CB 73.85
Oil Pan Gasket (1 piece rubber) 1986-89 L15CP 34.25
Head Gasket (Felpro) L15DA 19.50
Competition Head Gasket (Felpro #1035)
steel wire ring typeL15DF 59.50
Competition Head Gasket (extreme duty racing gasket) L15DR 29.50
Valve Cover Gasket- Cork L15E 6.79
Valve Cover Gasket H.D. (1 piece rubber) includes upper manifoldL15EA 24.00
Intake Manifold Gasket Set L15FA 11.40
Exhaust Manifold to Cylinder Head L15GA 7.50
Turbo Charger to Exhaust Manifold (stainless) L521GT 8.75
Water Outlet Gasket L15N CALL
Water Pump GasketL15P CALL
Camshaft Seal L15R 8.25
Auxiliary Shaft Seal L15S 9.25
Crankshaft Front Seal L15T 16.08
Oil Pump (standard)
MellingL2P 42.90
Oil Pump- (high pressure/ high volume) L2HP 73.20
Water Pump (new) L6A 73.10
Water Pump (recon) L6AA 39.00
Fuel Pump- Electric XR4Ti (in line) M10A 165.00
Fuel Pump- Electric XR4Ti (in tank) M10AT 125.00
Engine Components
Utilizing a design similar to the earlier German
2000 OHC "Pinto" engine the 2300 "Lima" en-
gine eventually replaced the 2000 OHC in most
North American Ford 4 cylinder vehicles from
1974 on. Built for lower maintenance with the
addition of hydraulic lash
adjusters the 2300
was designed to
operate in a lower
RPM range using
its larger displace-
ment and in-
creased torque to
its best advan-
tage. Perfor-
mance turbo-
charged versions
of the 2300 began
to appear in 1979 in
the Mustang/Capri and continued through the
80's in a more refined and powerfull EFI turbo
version. A reduced bore 2000 displacement
"Ranger" truck engine (from 1983-87) was also
produced. Some late production "Lima" engines
are equipped with hydraulic roller cam and valve
train, and other versions use dual spark plug
cylinder heads. The 2300 is a fairly rugged
engine in its stock form, however some compo-
nents will require up-rating with performance
components if high RPM duty is required. The
"Lima" series turbo and normally aspirated en-
gines respond quite well with a bit of perfor-
mance tuning and though lacking in refinement
do give quite a bit of bang for the buck.
Main Bearing Set- ACL/Vandervell (std, .010", .020", .030") L16A 32.65
Connecting Rod Set- (4) Forged H-beam 5.20" length L4ES 549.00
Connecting Rod Set- (4) Forged
I-beam 5.20" length L4ESB 398.00
Connecting Rod Set- (4) Forged H-beam 5.70" length L4ESA 549.00
Rod Bearing Set- ACL/Vandervell (std, .010", .020", .030") L16H 16.35
Con Rod Bolt Set- ARP H.D. (for standard 2.3L rod) L4FS 47.70
Head Stud Set- ARP H.D. L2DS 105.00
Cam Bearing Set- ACL/Vandervell L16M 18.50
Cam Bearing Set- ACL/Vandervell (360 degree O.D. groove) L16MA 18.50
Aux. Shaft Bearing L5DC 20.25
Cam Follower- (standard O.E. type)
eachL5B 7.50
Cam Follower- (roller type)
eachL5BR 16.00
Ring Set- Moly type 1/16", 1/16", 3/16" (std, .020", .030", .040", .060")
*for above "performance pistons" - specify sizeL4R 85.90
Ring Set*- Gapless Moly type 1/16", 1/16", 3/16" (std, .020", .030", .040", .060")
*for above "performance pistons" - specify sizeL4TF 98.00
Ring Set*- Gapless Moly type 1/16", 1/16", 3/16" (std, .025", .035", .045", .065")
*for above "performance pistons" - file fit top ringL4T1 127.50
Ring Set*- Gapless Moly type 2mm, 2mm, 4.75mm (std, .020", .030", .040", .060")
*for standard OE type pistons - specify sizeL4TFA 98.00
Performance Piston- Power Forged #250F (std, +.020", +.030", +.040", +.060 sizes)
exact replacement for standard 2.3 turbo piston, light weight "power forged"
design, 1.589" comperssion height for 8.0:1 compression, 2mm 2mm 4.75mm
ring land, supplied with wrist pins and locks.
L4-250F 62.20
Performance Piston- Forged (custom)
BAT can supply custom forged pistons to your specifications. Information regarding
bore size, ring land sizes & locations, compression height, and wrist pin bore size
is required for ordering. Pricing is on request
2 8
Page 30 of 45
Engine Components
Camshafts- see chart below
Hydraulic Lash Adjuster Set- (standard O.E. type) L5BA 43.00
Hydraulic Lash Adjuster Set- (high rev. anti pump-up) L5BH 49.95
Intake Valve- (standard O.E. type) L3H 8.25
Intake Valve- 1.740" (oversized stainless steel hi-flow)
eachL3HA 13.25
Intake Valve- 1.890" (oversized stainless steel hi-flow)
eachL3HB 15.00
Exhaust Valve- (standard O.E. type)
eachL31 25.75
Exhaust Valve- 1.510" (oversized stainless steel hi-flow)
eachL31A 13.25
Exhaust Valve- 1.590" (oversized stainless steel hi-flow)
eachL31B 15.00
Valve Spring Retainers (various)-
call with specific application------CALL
Valve Spring Set- (sport spring set for hydro cams to .480" lift) L3F 73.75
Valve Springs Racing-
call with specific application------CALL
Electric Fan Switch -XRM450FS 24.50
Knock Sensor-XRM450KS 52.70
Engine Coolant Temp Sensor (ECT)-XR M450EC 28.45
Idle Speed (Air Bypass Valve) XR/Scorpio
M450IS 79.90
Throttle Position Sensor (TPS)-XR M450TP 47.60
Oxygen Sensor (OS)-XRM450OS 60.50
Oil Pressure Switch-XRM450P 6.40
Water Temp Gauge Sender- XR (purple band)M450F 39.75
Adjustable Cam Sprocket (key way type) L5F 34.95
Adjustable Cam Sprocket (vernier type) L5FA 95.75
Cam Belt- (H.D. Ford Motorsport) L5G 29.95
Cam Belt- (H.D. Pirelli type)L5GA 15.00
Fuel Injector 2.3L Turbo (35pph -disk type) each L7G 68.50
Fuel Injector 2.3L Turbo- Remanufactured (35pph -brown top) each M7G 49.50
Intake Hose- Turbo Outlet to Throttle Body (Hi-Temp 4-Ply Silicone "Blue") XR4Ti, T-Bird & SVO M22H 47.00
Air Vane Meter* 50mm (T-Bird)
reconditionedL7V 164.50
Air Vane Meter* 65mm (SVO)
reconditionedL7VA 175.00
*can also be used for performance upgrade on XR4Ti with "PE" programed chip (call for information)
Distributor- 2.3L Turbo (reman) w/o cap, rotor, module (35.00 core) L9AB 119.00
Distributor Cap H.D. (hi-temp epoxy w/brass terminals) L9B 16.98
Distributor Rotor H.D. (hi-temp epoxy)
85-86 screw down typeL9F 7.50
Distributor Rotor H.D. (hi-temp epoxy)
87-89 push-on typeL9FA 8.90
Ignition Module TFI (on distributor) L9M 80.75
Ignition Wire Set- (8mm custom length w/silicone jacket and boots)L9HT 39.00
Ignition Wire Set- (8.5mm custom length w/silicone jacket and boots) M9HT69.50
Ignition Wire Set- (10mm custom length w/silicone jacket and boots)M9HTR 79.50
Performance Air Filter KN (2.3L Turbo) XR4Ti M22P 32.50
*durations quoted gross & .050" - timing events are @.050"
Grind#
Pricing $DescriptionPower
BandCam Lift
inlet/exhst.Valve Lift
inlet/exhst.Duration
inlet/exhTim ing
FiguresTiming
Inlet @
Full LiftValve
Clearance
inlet/exhst.Com m ents
2300 Turbo Camshafts (Hydraulic)
H260
$169.00Hydraulic2500-6000.252"/.252".416"/.416"272/272
220/2200/40 40/01100 / 0smooth idle, strong low and mid performance,
turbo suitable, auto & manual trans.
H283
$169.00Hydraulic3500-6500.274"/.274".453"/.453"276/276
224/2242/42 42/21100 / 0good idle, strong low and mid performance,
turbo suitable, manual transmission only
2300 Turbo Camshafts (Hydraulic Roller*) *for cars origionally equipped or kit available below
HR220
$385.00Hydro-roller2700-6500.305"/.305".505"/.505"272/222
221/231------1110 / 0H.P. roller cam for cars origionally roller cam equipped,
or see kit below- manual transmission only
HR225
$399.00Hydro-roller3000-6800.314"/.314".520"/.520"280/280
226/226------1110 / 0H.P. roller cam for cars origionally roller cam equipped,
or see kit below- manual transmission only
HR310
$375.00Hydro-roller3000-7000.317"/.317".535"/.535"284/284
224/2240/44 44/01120 / 0H.P. roller cam for cars origionally equipped.
turbos use 112 centerline, manual transmission only
2300 Turbo Camshaft Kits (Hydraulic Roller)
HR220K
$680.00Hydro-roller
cam kit2700-6500.305"/.305".505"/.505"272/222
221/231------1110 / 0Kit Includes: camshaft, roller followers, valve springs,
valve keepers & retainers, lash caps & cam oil seal
HR225K
$715.00Hydro-roller
cam kit3000-6800.314"/.314".520"/.520"280/280
226/226------1110 / 0Kit Includes: camshaft, roller followers, valve springs,
valve keepers & retainers, lash caps & cam oil seal
2 9