air conditioning FORD SIERRA 1991 2.G XR4 Workshop Manual

Bodywork
pL
pM
pNpE
pA pL
pC pD
pF
pBpG
pH
pI
pJ
pK
pA Front Fenders European Sierra fenders are a direct replacement for the
XR4Ti and are an attractive alternative considering the high price of the American
version. These fenders also include the holes required for side blinker mounting
(see below).
Note: specify left or right when ordering M806 L/R
pB
Inner Wheel Well Splash/Liners Replacements for the commonly
cracked, broken or missing inner fender splash on the XR4. Covers full inner
wheel house area as origional USA versions.
specify left or right M808L/R
pC
Door Skin - (specify left or right)M807 L/R
pD
Door Handle XR4 & Scorpio - (specify left or right)M362 L/R
pE
Door Sill (Rocker Panel) - (specify left or right)M803 L/R
pF
Rear Wheel Arch - (specify left or right)M804 L/R
pG
Battery TrayM817
pH
Rear PanelM815
pI
Cosworth Front Grille Nothing transforms the look of the XR4Ti quite like
adding a Cosworth grille. Designed with a center opening, the Cosworth grille
adds additional air flow to the radiator and A/C condenser for a cooler running
engine and better air conditioning performance. An intercooler could also be fitted
behind the grille opening as is done on the original Cosworth Sierra and R/S 500
models.
Note: Grilles are O.E. quality (injection moulded plastic) not shoddy fiberglass
replicas. Suppled (primed) un-painted- includes "Ford" emblem
M320
pJ
Grille Surround Gasket This gasket will almost always need to be
replaced when fitting a new grille.M320S
pK
European Side Blinker Lamp Kit Add an extra degree of safety when
signaling to turn. Side blinkers fit above European fenders without modification
and can also be fitted to standard Merkur XR4Ti fenders by drilling a mounting
hole. Kit includes (2) lamps, wiring and templates.M317
pL
Cosworth Hood Original equipment Ford Sierra Cosworth hoods are
designed to receive hood vents/louvers for additional under hood cooling. These
hoods look quite distinctive as the raised center section is lower and wider than
on the standard XR4 hood giving the car a more aggressive appearance.M813
pM
Cosworth Hood Vents Hood louvers/vents are both visually striking and
functional as they help to ventilate the engine compartment. These O.E. Ford vents
(pair) bolt into the Cosworth hood (above) or can be fitted to standard hoods by cutting
a hole and bonding them in place.
(see pg 11 for fiberglass versions)M814
pN
Cosworth Front Spoiler/Bumper We supply everything required to
install the stunningly attractive Cosworth Sierra front spoiler/bumper to your
XR4Ti. All components are original Ford including; bumper, bumper bar
brackets, lower side fender mounting panels, fog lamps, turn signal lamps, and
assorted hardware (clips & fasteners).
Note: bumpers are supplied in white-
can be painted to match other colors.
M353
(R/S 500 Version) M353RS
1 2

pFpG
Automotive air conditioning components seem to be difficult to source and expensive to boot. The XR4 and Scorpio are no
exception to the rule. Reason being, a functioning A/C system is considered a "must have" and some will pay almost any price
for cold air on a hot day. BAT understands that comfort is paramount, but on the other hand it should not require a second
mortgage to repair your A/C system. You will find we have a selection of high quality, economically priced A/C parts too help
keep you cool without breaking the bank.
Most A/C Components for XR4 & Scorpio are interchangeable except where noted.
pA
pI
pJ
pB
pEpD
pH
pA
Evaporator- The evaporator (alloy fin/tube design) works
as a heat exchanger. Air flowing through the core is cooled,
cleaned, and dried. It is also one of the major cost portions
of the A/C system, with the Ford original costing around
$550.00. Check out our aftermarket alternative for less than
half the cost !
M470E
pB
Expansion Valve- Meters the volume of refrigerant to the
evaporator. Expansion valve assembly should be replaced with
evaporator or if found faulty. M470EV
pC
Blower Motor- HVAC system blower motor includes motor
and fan wheel. (Scorpio) G470A (XR4) M470A
pD
Refrigerant Hoses*- The complete refrigerant hose manifold
assembly. These are specially re-manufactured units that have
the hose running to the fire wall extended so it can be routed
further away from the turbo's excessive heat. This is a very
common failure item. (XR4ti)
extended hose M470H
(Scorpio)
standard length hose G470H
*additional $100.00 core charge on this item- refundable on return
pE A/C Compressor- The compressor is one of the major cost
portions of the A/C system, with the Ford original costing upwards
of $850.00. Check out our
brand new Nippondenso A/C compressor
units that are complete including the clutch assembly.
M470C pC
pF
Clutch Assembly*- Replacement magnetic clutch
assembly. Available separately from compressor . If a clutch is all
you need we have it. M470CL
*additional $25.00 core charge on this item- refundable on return
pG Condenser- The A/C condenser (alloy tube/fin core)
is located ahead of the water radiator. Designed to cool
the compressed refrigerants air passes over the cooling
fins extracting heat to change hot gasses back to liquid
refrigerant as it cools. Again, one of the major cost
portions of the A/C system, with the Ford original costing
upwards of $600.00. Check out our aftermarket alternative
for considerable cost savings! for XR4 M470D
for Scorpio G470D
pH
Electric Fan- An alternative to the expensive original
condenser fan ($450.00). This highly efficient (1200 cfm) 16"
electric "pusher" fan moves more air
for le$$. A16F-PU
pI
Pressure Switch- The triple pressure switch assembly
engages the condenser fan and switches off the compressor clutch
with high/low pressure. Also a common failure item.
M470S
pJ Receiver/Dryer- Works as a storage/expansion tank for
refrigerant as well as a system dehumidifier. It is common to
replace the dryer when changing over to newer types refrigerants
or whenever the A/C system has been open to atmosphere as the
dryer is easily contaminated. M470R
Air Conditioning System2 4