ignition FORD SIERRA 1992 2.G Braking System Workshop Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1992, Model line: SIERRA, Model: FORD SIERRA 1992 2.GPages: 22, PDF Size: 1.11 MB
Page 3 of 22

8Open the bleed screw half a turn and have
your assistant depress the brake pedal slowly
to the floor and then, after the bleed screw is
retightened, quickly remove his foot to allow
the pedal to return unimpeded. Repeat the
procedure.
9Observe the submerged end of the tube in
the jar. When air bubbles cease to appear,
tighten the bleed screw when the pedal is
being held fully down by your assistant.
10Top-up the fluid reservoir. It must be kept
topped up throughout the bleeding
operations. If the connecting holes to the
master cylinder are exposed at any time due
to low fluid level, then air will be drawn into
the system and work will have to start all over
again.
11Assuming that the complete system is
being bled, the procedure described in the
preceding paragraphs should be repeated on
the front right-hand caliper followed by the
rear right-hand and left-hand wheel cylinders.
12On completion, remove the bleed tube,
and discard the fluid which has been bled
from the system unless it is required for bleed
jar purposes. Never re-use old fluid.
13On completion of bleeding, top-up the
fluid level in the reservoir. Check the action of
the brake pedal, which should be firm and free
from any “sponginess” which would indicate
that air is still present in the system.
With one-way valve
14There are a number of one-man brake
bleeding kits currently available from motor
accessory shops. It is recommended that one
of these kits should be used whenever
possible, as they greatly simplify the bleeding
operation and also reduce the risk of expelled
air or fluid being drawn back into the system.
15Proceed as described in paragraphs 5
and 6.
16Open the bleed screw half a turn then
depress the brake pedal to the floor and
slowly release it. The one-way valve in the
bleeder device will prevent expelled air from
returning to the system at the completion of
each stroke. Repeat this operation until clear
hydraulic fluid, free from air bubbles, can be
seen coming through the tube. Tighten the
bleed screw.
17Proceed as shown in paragraphs 11 to 13.
With pressure bleeding kit
18These too are available from motor
accessory shops and are usually operated by
air pressure from the spare tyre.
19By connecting a pressurised container to
the master cylinder fluid reservoir, bleeding is
then carried out by simply opening each bleed
screw in turn and allowing the fluid to run out,
rather like turning on a tap, until no air bubbles
are visible in the fluid being expelled.
20Using this system, the large reserve of
fluid provides a safeguard against air being
drawn into the master cylinder during the
bleeding operations.21This method is particularly effective when
bleeding “difficult” systems or when bleeding
the entire system at time of routine fluid
renewal.
22Begin bleeding with reference to
paragraphs 5 and 6 and proceed as described
in paragraphs 11 to 13.
1Keep the fluid reservoir replenished
throughout the bleeding operations.
2Remove the dust cap where fitted, and
clean around the bleed screw on the left-hand
front caliper. Fit a bleed tube to the screw and
immerse the open end in a jar containing
clean hydraulic fluid.
3Open the bleed valve one full turn and have
an assistant depress the brake pedal fully and
hold it down.
4Close the bleed valve and release the brake
pedal. Repeat the procedure until fluid ejected
from the end of the tube is free from air
bubbles.
5Repeat the operations on the right-hand
front caliper.
6Fit the bleed tube to the left-hand rear
caliper and open the bleed valve one full turn.
7Have an assistant depress the brake pedal
fully and hold it down.
8Switch on the ignition to position ll.
9Allow the fluid to bleed from the tube for at
least 15 seconds, when the fluid should be
free from air bubbles.
10Close the bleed valve.
11Release the brake pedal and wait for the
hydraulic pump to stop.
12Fit the bleed tube to the right-hand rear
caliper and open the bleed valve one full turn.
13Have your assistant depress the brake
pedal through half its travel and hold it there.
Allow the fluid to bleed from the tube for at
least 15 seconds, when the fluid should be
free from air bubbles.
14Close the bleed valve.
15Release the brake pedal and wait for the
hydraulic pump to stop then switch off the
ignition.
16Top-up the reservoir with clean fluid.
17When the hydraulic system is being bled
for the purpose of renewing the fluid at the
specified interval, as each caliper is bled,
operate the brake pedal continuously until
clean fluid is seen to enter the jar.
18When the hydraulic pump is running its
note will be heard to change once fluid has
purged through it. Do not allow the pump torun continuously for more than two minutes. If
it does run for a longer period, switch off the
ignition and allow the motor to cool for ten
minutes.
19On completion, discard the fluid which
has been bled from the system unless it is
required for bleed jar purposes. Never re-use
old fluid.
20Check the action of the brake pedal,
which should be firm and free from any
“sponginess”, which would indicate that air is
still present in the system.
Front disc pads
1The disc pad friction material can be
inspected for wear without removing the
roadwheels. Working beneath the vehicle,
insert a mirror between the caliper and the
roadwheel and check that the friction material
thickness is not less than the minimum given
in the Specifications.
2If any one of the pads has worn below the
specified limit, the front pads must be
renewed as an axle set (4 pads).
3To renew the pads, slacken the front
roadwheel nuts, apply the handbrake, then
jack up the front of the vehicle and support on
axle stands (see “Jacking and Vehicle
Support”). Remove the roadwheels. On P100
models, mark the position of the roadwheels
in relation to the wheel studs before removal.
4Proceed as follows according to model:
Girling caliper (1.3 and early 1.6 litre
models)
5Where applicable, disconnect the wiring to
the disc pad wear sensor.
6Unscrew and remove the bolt from the
upper caliper guide pin while holding the pin
stationary with a spanner (see illustration).
7Swing the caliper downwards and lift out
the disc pads. If the outboard pad is stuck to
4Disc pads -inspectionand
renewal
3Brake hydraulic system (ABS)
- bleeding
Braking system 10•3
10
4.6 Unscrewing the bolt from the upper
caliper guide pin - Girling caliper
Caution: Refer to the
precautions in Section 1.
Caution: The rear brake
hydraulic circuit may be under
considerable pressure, take
care not to allow hydraulic fluid
to spray into the face or eyes. Refer to the
precautions in Section 1.
Page 5 of 22

the caliper, and the caliper body is modified
accordingly. Also, plastic covers are fitted to
the caliper guide bolts (see illustrations).
22Procedures are unchanged from those
given above.
Rear disc pads
23Slacken the rear roadwheel nuts, chock
the front wheels, then jack up the rear of the
vehicle and support on axle stands. (see
“Jacking and Vehicle Support”). Remove the
roadwheel.
24The disc pads can be inspected through
the top of the caliper after removal of the
blanking spring clip. Check that the friction
material thickness is not less than the
minimum given in the Specifications.
25If any one of the pads has worn below the
specified limit, the rear pads must be renewedas an axle set (4 pads).
26To renew the pads, proceed as follows.
27Release the handbrake, and free the
handbrake cable from the suspension lower
arm by bending back the tangs.
28Where applicable, disconnect the wiring
to the disc pad wear sensor (see illustration).
29Unscrew and remove the bolt from the
forward caliper guide pin, while holding the
pin stationary with a spanner (see
illustration).
30Swing the caliper rearwards and lift out
the disc pads (see illustration). Do not
depress the brake pedal with the caliper
removed.
31Brush all dirt and dust from the caliper,
pads and disc, but do not inhale it as it may
be injurious to health. Scrape any corrosion
from the disc.32As the new pads will be thicker than the
old ones, the piston must be retracted into its
bore to accommodate the new thicker pads.
Retracting the piston will cause the fluid level
in the reservoir to rise, so to avoid spillage,
syphon out some fluid using an old
hydrometer or a teat pipette. Retract the
caliper piston by turning it clockwise. Ford
tool No 12-006 is designed for this purpose,
but a pair of circlip pliers or any similar tool
can be used instead (see illustration).
33Remove the backing paper from the new
pads, and fit them to the caliper.
34Further refitting is a reversal of removal,
bearing in mind the following points.
35If disc pads with wear sensors are fitted,
the pad with the sensor wire should be fitted
inboard.
36Repeat the procedure on the opposite
rear brake.
37On completion, switch on the ignition and
apply the footbrake hard several times to
settle the pads. Switch off the ignition, then
check and if necessary top-up the fluid level in
the reservoir. Check the operation of the
handbrake.
38Avoid heavy braking, if possible, for the
first hundred miles or so after fitting new
pads. This will allow the pads to bed in and
reach full efficiency.
Braking system 10•5
10
4.21a Later type front disc pad retaining
clip
4.32 Retracting the piston using circlip
pliers4.30 Lift out the disc pads
4.28 Rear disc pad wear sensor wiring clip
(arrowed)
4.29 Unscrewing the forward caliper guide
pin bolt
4.21b Removing a caliper guide bolt cover
- later type
4.20b Refitting the caliper retaining clip -
Teves caliper4.20a The clip on the back of the inboard
disc pad fits into the piston recess - Teves
caliper
Page 10 of 22

Note: Complete dismantling of the rear caliper
should not be attempted unless Ford spring
compressor (tool No 12-007) is available, or
unless the problems likely to arise in the
absence of the tool are understood. Renewal
of the piston seal dust-excluding seal and
piston adjuster nut seal requires no special
tools.
Removal
1With the ignition switched off, pump the
brake pedal at least 20 times, or until it
becomes hard, to depressurise the system.
2Chock the front wheels, slacken the
relevant roadwheel nuts, then jack up the rear
of the vehicle and support on axle stands (see
“Jacking and Vehicle Support”). Remove the
roadwheel and release the handbrake.
3Where applicable, disconnect the wiring to
the disc pad wear sensor.
4Proceed as described in Section 6,
paragraphs 2 and 3, but note that the rigid
brake pipe is clipped to the suspension lower
arm.
5Unscrew and remove the two guide bolts
securing the caliper to the carrier bracket,
while holding the pins with a spanner. Unhookthe handbrake cable from the lever, and
withdraw the caliper. Alternatively, the two
carrier bracket-to-hub carrier bolts can be
unscrewed, and the caliper and carrier can be
separated on the bench, but in this case the
handbrake cable must be disconnected from
the carrier bracket by removing the retaining
circlip.
Overhaul
6Clean the caliper, taking care not to inhale
any dust which may be injurious to health, and
mount it in a soft-jawed vice.
7Rotate the piston anti-clockwise, using
Ford tool No 12-006, or a pair of circlip pliers
or similar tool, until it protrudes from the
caliper bore by approximately 20.0 mm (0.8
in). Free the dust-excluding seal from the
groove in the piston, then continue
unscrewing the piston and remove it. Remove
and discard the dust-excluding seal.
8The piston and bore may now be cleaned
and examined as described in Section 6,
paragraph 12.
9The piston adjuster nut seal should be
renewed as follows.
10Remove the circlip from the piston, then
extract the thrustwashers, wave washer and
thrust bearing. Note the fitted sequence of
these components. Finally remove the nut
(see illustrations).
11Remove the seal from the nut, noting
which way round it is fitted. Clean the nut with
methylated spirit. Lubricate the new seal with
clean hydraulic fluid and fit it to the nut.12If no further dismantling is required,
proceed to paragraph 20.
13For further dismantling it is virtually
essential to have Ford tool 12-007 in order to
compress the adjuster spring. This tool
appears to be a cut-down adjuster nut with a
handle for turning it. In the workshop it was
found that the actual piston adjuster nut could
be used to compress the spring if it were
turned with circlip pliers (see illustration).
This works well enough for dismantling, but
reassembly proved extremely difficult
because of the limited clearance between the
skirt of the nut and the caliper bore.
14Having compressed the adjuster spring
just enough to take the load off the circlip,
release the circlip inside the caliper bore.
Remove the spring compressor, then extract
the circlip, spring cover, spring and washer
(see illustrations).
7Rear disc caliper - removal,
overhaul and refitting
10•10Braking system
7.10a Remove the circlip from the rear
caliper piston . . .7.10c . . . a wave washer and (not shown)
another thrustwasher . . .
7.14a Extract the circlip from the caliper
bore . . .
7.13 Using the piston adjuster nut to
compress the adjuster spring7.10e . . . and finally the adjuster nut itself.
Note the seal (arrowed) on the nut7.10d . . . then the thrust bearing . . .
7.10b . . . followed by the thrustwasher . . .
Caution: Refer to the
precautions in Section 1.
Page 16 of 22

7Remove the clip from the hydraulic unit
pushrod on the brake pedal.
8With an assistant supporting the hydraulic
unit, unscrew the four nuts which secure the
unit to the bulkhead (see illustration).
Withdraw the unit from under the bonnet.
9Recover the gasket fitted between the unit
and the bulkhead.
10Drain the fluid from the reservoir. Do not
actuate the pushrod with the unit removed.
11Dismantling of the hydraulic unit should
be limited to the operations described in the
following Sections (see illustration).
Refitting
12Refitting is a reversal of removal, bearing
in mind the following points.13Do not refill the fluid reservoir until
reassembly and refitting is complete.
14Use a new gasket between the hydraulic
unit and the bulkhead.
15Ensure that the hydraulic pipes are
reconnected to the correct unions.
16On completion, bleed the complete
hydraulic system and check for leaks around
all disturbed components.
Note: A new O-ring must be used between
the accumulator and the hydraulic unit on
refitting.
Removal
1Disconnect the battery negative lead.
2Depressurise the hydraulic system by
pumping the brake pedal at least 20 times, or
until it becomes hard.
3Wrap a clean rag round the base of the
accumulator to catch any spilt fluid.
4Unscrew the accumulator using a hexagon
key. Remove the accumulator, noting the
sealing ring and being prepared for fluid
spillage (see illustration). If fluid isaccidentally spilt on the paintwork, wash off
immediately with cold water.
Refitting
5Fit a new O-ring to the base of the
accumulator, fit the accumulator and tighten
it.
6Reconnect the battery. Switch on the
ignition and check that the hydraulic unit
pump stops within 60 seconds; if not, the
accumulator is likely to be faulty.
7On completion, bleed the complete
hydraulic system and check for leaks around
all disturbed components.
Note: New sealing washers must be used on
the high pressure fluid hose banjo union, and
a new O-ring must be used between the
accumulator and the hydraulic unit on refitting.
Removal
1Remove the accumulator.
2Prepare a suitable container to catch spilt
fluid, and disconnect the high pressure fluid
hose from the pump.
3Remove the securing spring clip and
disconnect the low pressure fluid hose from
the pump. Allow the fluid to drain out of the
hose into the container. If fluid is accidentally
spilt on the paintwork, wash off immediately
with cold water.
4Disconnect the multi-plugs from the
pressure switch and the pump motor.
5Remove the pump mounting bolt (see
illustration).
6Pull the pump and motor assembly off the
mounting spigot and remove it.
7Recover the mounting bushes and renew
them if necessary.
8If a new pump is to be fitted, transfer the
pressure switch to it, using a new O-ring.
18Hydraulic unit pump and motor
(ABS) - removal and refitting
17Hydraulic unit accumulator
(ABS) - removal and refitting
10•16Braking system
16.8 Hydraulic unit-to-bulkhead securing
nuts (arrowed) - ABS
17.4 Unscrew the accumulator and remove
it, noting the O-ring (arrowed)
16.11 Hydraulic unit components - ABS
A Fluid reservoir
B Accumulator
C Main valveD Master cylinder
E Pushrod
F Pump and motorG Booster
H Pressure switch
J Valve block
Caution: Refer to the
precautions in Section 1.
Caution: Refer to the
precautions in Section 1.
Page 17 of 22

Refitting
9Commence refitting by offering the pump to
the mounting spigot, then reconnecting the
low pressure fluid hose.
10Refit and tighten the pump mounting bolt.
11Reconnect the high pressure fluid hose,
using new sealing washers on the banjo
union.
12Refit the accumulator, using a new O-ring.
13Reconnect the multi-plugs and the
battery.
14Refill the fluid reservoir, then switch on the
ignition and allow the pump to prime itself.
Allow the pump to run for a maximum of two
minutes at a time then leave it for ten minutes
to cool down.
15On completion, bleed the complete
hydraulic system and check for leaks around
all disturbed components.
Note: To remove the pressure switch from the
hydraulic unit in situ, Ford tool No 12-008 or a
locally made equivalent will be required. The
switch may be removed without special tools
after removing the hydraulic unit complete or
the pump above. A new O-ring must be used
when refitting the switch.
Removal
1Disconnect the battery negative lead.
2Depressurise the hydraulic system by
pumping the brake pedal at least 20 times, or
until it becomes hard.
3Disconnect the multi-plug from the switch,
then unscrew and remove the switch.
Refitting
4Refit the switch using a new O-ring.
Position the plastic sleeve so that the drain
hole faces the pump motor, then tighten the
switch (see illustration).
5Reconnect the multi-plug and the battery.
6On completion, bleed the complete
hydraulic system and check for leaks around
all disturbed components.
Removal
1Disconnect the battery negative lead.
2Depressurise the hydraulic system by
pumping the brake pedal at least 20 times, or
until it becomes hard.
3Apply the handbrake, and slacken the
left-hand front wheel nuts. Jack up the front of
the vehicle and support on axle stands (see
“Jacking and Vehicle Support”).Remove the
left-hand front wheel.
4Remove the plastic liner from under the
wheel arch.
5Prepare a suitable container to catch spilt
fluid, clean around the unions on the valve
block, then unscrew and disconnect the fluid
pipes (see illustration). Plug the open ends of
the pipes and valve block to prevent fluid
leakage and dirt ingress. If fluid is accidentally
spilt on the paintwork, wash off immediately
with cold water.
6Disconnect the multi-plug and the earth
strap from the valve block.
7Working through the wheel arch, unscrew
the three nuts which secure the valve block
mounting bracket (see illustration).8Remove the valve block and mounting
bracket, taking care not to spill brake fluid on
the paintwork.
9No further dismantling of the valve block is
possible, but the pressure regulating valve in
the rear brake pipe union can be renewed if
desired.
Refitting
10Refitting is a reversal of removal.
11On completion, bleed the complete
hydraulic system and check for leaks around
all disturbed components.
Removal
1Disconnect the battery.
2Working inside the vehicle, prise out the
facia trim panel from the passenger’s side.
Remove the insulation.
3To remove the now exposed module, push
it as necessary to release the retaining catch.
21Computer module (ABS)
- removal and refitting
20Valve block (ABS) -removal
andrefitting
19Hydraulic unit pressure switch
(ABS) - removal and refitting
Braking system 10•17
10
20.5 Valve block and associated
components - ABS
A Bracket screws
B Adapter plate
C valve blockD Multi-plug
E Earth strap
anchor point
19.4 Refit the pressure switch with the
drain hole (arrowed) in the plastic sleeve
facing the pump motor - ABS18.5 Hydraulic unit pump mounting bolt -
ABS
20.7 Unscrewing the valve block mounting
bracket nuts (arrowed) - ABS
Caution: Refer to the
precautions in Section 1.
Caution: Refer to the
precautions in Section 1.