height adjustment FORD SIERRA 1993 2.G Bodywork And Fittings Workshop Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1993, Model line: SIERRA, Model: FORD SIERRA 1993 2.GPages: 22, PDF Size: 1.2 MB
Page 15 of 22
4Immerse the housing assembly in a
container of hot water for approximately ten
minutes, then prise the hinge cover from the
housing, and using a screwdriver, prise the
filler flap hinge legs out of the sockets in the
housing.
Refitting
5Commence refitting by warming the filler
flap and housing, as during removal, then
push the flap hinge legs into the housing.
6Further refitting is a reversal of removal,
ensuring that the housing gasket and retaining
tangs are correctly located.
Removal
1Open both the front and rear doors to
expose the relevant weatherstrip.
2Carefully pull the weatherstrip from the
base of the front pillar, taking care to release
the flap which is stuck to the pillar with
adhesive.
3Pull the remainder of the weatherstrip from
its flange.
4Carefully clean the old adhesive from the
base of the front pillar using methylated
spirits.
Refitting
5Commence refitting by pushing the
weatherstrip onto its flange at the top corner
of the rear pillar, running it for approximately
200 mm (8.0 in) along the horizontal flange.
6Align the flap on the front pillar, and apply a
thin bead of rubber-based adhesive to the
flap. Refit the flap to the front pillar, ensuring
that it lies naturally. Should the flap not lie
naturally, or start to lift, temporarily secure it in
position with adhesive tape.
7Refit the remainder of the weatherstrip,
starting at the front pillar and working
rearwards, then close the doors and allow the
adhesive to dry for at least an hour.
Glass panel - removal and
refitting
1Open the sunblind and remove the three
screws and clips shown (see illustration)
then slide the lower frame rearwards into the
roof.
2Remove the six screws securing the glass
panel to the sliding gear (see illustration)
then push the glass panel upwards and
remove it from outside of the vehicle, taking
care not to damage the paintwork.
3Commence refitting by securing the glass
panel to the sliding gear with the six screws.
4Adjust the sunroof as described in
paragraphs 10 and 12 to 14 inclusive, but
note that there is no need to open and close
the roof before checking adjustment.
5Refit the three clips to the glass panel, then
pull the lower frame forwards and secure it to
the glass panel with the three screws. Tighten
the screws in the order shown.
Complete assembly - removal and
refitting
6Fully open the sliding roof panel, then
remove the screw securing the roof operating
handle and detach the handle.
7Remove the four screws on each side and
the two screws at the front securing the
sliding roof assembly to the roof tray.
8Lift the front rail and carefully withdraw the
assembly forwards from the roof tray, taking
care not to damage the paintwork.
9Refitting is a reversal of removal, but on
completion, adjust the sunroof as described in
paragraph 10 onwards, and if necessary
adjust the position of the roof operating
handle so that with the roof in its closed
position, the handle can fold into its recess.
Adjustment
10Fully open and close the sliding roof, then
check that the front edge of the glass panel is
flush with, or a maximum of 2.0 mm (0.08 in)
below the adjacent roof panel. The rear edge
of the glass panel should be flush with, or amaximum of 2.0 mm (0.08 in) above the
adjacent roof panel.
11If adjustment is necessary, remove the
three screws securing the glass panel to the
lower frame, then slide the lower frame
rearwards into the roof.
12To adjust the front edge of the glass
panel, loosen the front and centre screws
securing the glass panel to the sliding gear.
13To adjust the rear edge of the glass panel,
loosen the rear and centre screws securing
the glass panel to the sliding gear (see
illustration 39.1).
14On completion of adjustment, tighten the
glass panel-to-sliding gear securing screws.
15Pull the lower frame forwards and secure
it to the glass panel with the three screws.
Tighten the screws in the order shown.
1The method of removal and refitting for
most interior trim panels is self-explanatory.
The panels are fixed in place either by screws,
which may be concealed by plastic blanking
plugs in some cases, or by clips on the rear of
the panel.
2When removing a panel secured by clips,
prise the panel as close as possible to each
clip, using a forked tool similar to that shown
(see illustration, 17.6b) or a wide-bladed
screwdriver to prevent damage to the panel.
3Refer to the relevant Sections of this
Chapter for removal and refitting details of the
major trim panels.
Front pillar
1Remove the two trim panel securing screws
and withdraw the panel(see illustration)..
2Refitting is a reversal of removal.
Centre pillar
3Where applicable, lever the seat belt height
adjuster button downwards and detach the
button by removing the two securing screws.
41Interior pillar trim panels -
removal and refitting
40Interior trim panels - general
information
39Sunroof - removal, refitting
and adjustment
38Inner gutter weatherstrip
(Saloon, Hatchback and
Estate models) - removal and
refitting
Bodywork and fittings 12•15
12
39.2 Sunroof glass panel-to-sliding gear
securing screws (one side shown for
clarity)39.1 Sunroof lower frame-to-glass panel
securing screws and clips (arrowed)
Tighten screws in the order shown when
refitting37.2 Fuel filler housing securing screw
(arrowed)
Page 19 of 22
Removal
1Disconnect the battery negative lead.
2Open the sunroof.
3On models with a manually-operated
sunroof, remove the sunroof handle securing
screw, then withdraw the handle and trim plate.
4On models with an electric sunroof, remove
the operating switch.
5Remove the courtesy lamp, if necessary,
then remove the two screws from the front of
the console (see illustration).
6Remove the two screws securing the rear of
the console to the sunroof flange, and
withdraw the console.
Refitting
7Refitting is a reversal of removal.
Saloon, Hatchback and Estate
models
1On Saloons, remove the rear seat back.
2Loosen the upper screws of all the pillar
trim panels touching the headlining.
3Prise off the covers and remove the screws
from the passenger grab handles. Withdraw
the grab handles. Similarly, prise off the
blanking covers and remove the headlining
securing screws from the driver’s position.
4Disconnect the battery negative lead, then
prise the courtesy light(s) from the headlining
or overhead console. Disconnect the wiring
and remove the courtesy light(s).
5Where applicable, remove the two securing
screws and withdraw the overhead console.
6Remove the sunroof (where fitted). The
headlining is folded around the sunroof
aperture flange and is held in place with
adhesive tape and a moulding which must be
removed.
7Support the headlining, then remove the
screws and withdraw the sun visors and clips.
Where applicable, disconnect the wiring from
the vanity mirror lamp.
8On Estate models, remove the two plastic
fasteners from the headlining between the
rear door and tailgate pillars.
9Remove the two plastic fasteners from the
rear of the headlining, and withdraw the
headlining through the luggage compartment.
10Refitting is a reversal of removal.
P100 models
11Loosen the front pillar trim panel upper
securing screws.
12Prise off the covers and remove the
screws from the passenger grab handle.
Withdraw the grab handle.13Prise off the blanking cover and remove
the headlining securing screw from the
driver’s side.
14Disconnect the battery negative lead, then
prise the courtesy light from the headlining.
Disconnect the wiring and remove the
courtesy light.
15Support the headlining, then remove the
screws and withdraw the sun visors and clips.
16Remove the blanking covers, and the
three securing screws from the rear of the
headlining, then withdraw the headlining
through one of the door apertures.
17Refitting is a reversal of removal.
Front seat
1Slide the seat fully forwards, and on seats
with height adjustment unhook the tension
spring from the rear crosstube. Where
applicable, disconnect the wiring from the
seat heating pad(s).
2Unscrew and remove the two bolts from the
inner rear seat mounting bracket and the
single bolt from the outer rear seat mounting
bracket (see illustration).
3Slide the seat fully rearwards, then unscrew
and remove the single bolt from each front
seat mounting bracket. Withdraw the seat
from the vehicle.
4Refitting is a reversal of removal, but when
fitting the front and rear mounting bolts,tighten the inner bolts first in each case.
Where applicable locate the height
adjustment tension spring between the weld
pips on the crosstube.
Rear seat cushion
5Remove the single screw from each side,
securing the cushion to the heel kick panel.
6Pull the cushion forwards and remove it
from the vehicle.
7Refitting is a reversal of removal.
Rear seat backrest
Fixed rear seats
8Remove the seat cushion as described in
paragraphs 5 to 7.
9Remove the three now exposed Torx
screws from the base of the backrest.
10Working inside the luggage compartment,
remove the three nuts securing the backrest
to the body.
11Pull the backrest forwards into the
passenger compartment and remove it from
the vehicle. Where applicable, feed the rear
seat belt straps and buckles around the edges
of the backrest.
12Refitting is a reversal of removal.
Folding rear seats
13Release the catch and fold the seat
backrest forwards.
14Remove the two Torx screws from each
backrest hinge.
15Pull the backrest forwards into the
passenger compartment and remove it from
the vehicle. Where applicable, feed the rear
seat belt straps and buckles around the edges
of the backrest.
16Refitting is a reversal of removal, but
where necessary adjust the position of the
seat catch striker to achieve correct operation
of the catch.
Rear seat side cushion
Saloon models
17Working in the luggage compartment,
remove the nut from the side cushion stud.
18Working in the passenger compartment,
remove the rear seat cushion as described in
paragraphs 5 and 6.
19Expose the seat backrest hinge bolt by
removing the cover, then remove the bolt.
20Pull the top of the side cushion forwards
to disengage the stud from the body.
21Straighten the metal retaining tangs at the
base of the side cushion, then withdraw the
cushion.
22Refitting is a reversal of removal.
Hatchback and Estate models
23Fold down the rear seat backrest.
24Carefully bend back the side cushion
lower retaining tangs, then unhook the
cushion from the upper fixing on the rear
parcel shelf support (see illustration).
25Refitting is a reversal of removal.
47Seats - removal and refitting
46Headlining - removal and
refitting
45Overhead console - removal
and refitting
Bodywork and fittings 12•19
12
47.2 Front seat inner rear mounting
45.5 Overhead console securing screws (A)