clock FORD SUPER DUTY 2008 2.G Quick Reference Guide

Audiophile in-dAsh six Cd/Mp3/sA tellite CoMpAtible sound systeM
Tire PressureYour tire pressure needs to be properly set according to the recommended specifications. These specifications can be found on the Safety Compliance Certification Label or Tire Label which is located on the B-Pillar or the edge of the driver’s door. Please check your tire pressure during routine maintenance and seasonal changes. Tire pressure is specified to provide the appropriate load capacity for your vehicle’s axle load ratings. Keeping the tires at the proper pressure is an important part of maintaining your vehicle. Warning: Improperly inflated tires can affect vehicle handling and can fail suddenly, resulting in a possible loss of vehicle control.
FusesIf your electrical components are not working properly, a fuse may have blown. Please refer to your Owner’s Guide for fuse locations. Fuel PumP shuT
-OFF swiTch
This device stops the electric fuel pump from sending fuel to the engine when your vehicle has had a substantial jolt. After an accident, if the engine cranks but doesn’t start, the switch may have been activated. The fuel pump shut-off switch is located on the passenger side of the instrument panel. You have to open the passenger side door and remove the access panel to reset the switch. For switch reset instructions, please refer to your Owner’s Guide.
lOcaTiOn OF sP are Tire and
T OOls/c hanging The Tires
Your vehicle’s jack, lug wrench and lug wrench extension (if equipped) are installed in your vehicle in different locations based on cab configuration. Please refer to your Owner’s Guide for detailed information on tire changing tools and tire changing instructions. rO
adside emergencies
During your vehicle’s limited warranty period, the assurance and support of a 24-hour emergency roadside assistance program is included. Roadside assistance includes such services as fuel delivery, tire changes, jump starts, winch-outs, towing (limited distance) and lock-out assistance. Complete your roadside assistance identification card and keep it handy (such as in your wallet) for quick reference. This identification card is located in either your Owner Guide portfolio in the glove compartment (U.S.) or the Customer Information Guide in the glove compartment (Canada). memOry sea
Ts/mirr Ors/adjus Table Pedals
(if equipped)
This system allows automatic positioning of the driver seat, power mirrors, and adjustab le pedals in
two programmable positions. The memory seat control is located on the driver’s door trim panel.
To program position 1, move the driver seat, mirrors and pedals (if equipped) to the desired position
using the associated controls. Press the SET control. The SET control indicator light will briefly
illuminate. While the light is illuminated, press control 1. Repeat this procedure to program position 2. The vehicle must
be stationary (in Park or Neutral) to recall a position setting.
TailgaTe sTeP
(if equipped)
Your vehicle may be equipped with a feature that allows easy entry into the truck bed. To use the
tailgate step, open the tailgate. Pull the yellow latch lever to the unlock position to release t he
grab handle from its stowed position and raise the handle upright until you feel it latch and see
the latch lever in the lock position. The yellow lever only needs to be used when releasing the grab
handle. Rotate the center molding to unlatch the tailgate step. Pull the tailgate step out and down.
Flip open the panel to widen the step. Note: Always use the grab handle when
stepping up or down on the tailgate step. Keep the step load (you + load) below
350 lbs. (159 kg).
To close the tailgate step, fold the step panel, then
lift and fully slide the tailgate step into the
tailgate. Pull up on the yellow latch lever at the bottom of the handle, then lower the
handle. Note: Never drive with the step deployed. Fully close and latch the tailgate
step before moving the vehicle.
bed exTender
(if equipped)
Your vehicle may be equipped with a
cargo management feature in the
pick-up box. To open the bed extender
into tailgate mode, pull the locking pin
toward the driver’s side of the vehicle.
Rotate the storage hinge rearward to
unlatch the panels and then rotate
the panels toward the tailgate. Repeat
for the other side of the bed extender.
Finally, connect the two panels, then
rotate both knobs a quarter turn
clockwise to secure them. Ensure the latch rod is inserted into the tailgate
hole and the locking pins on both sides are engaged into their holes in the
pick-up box. Please refer to your Owner’s Guide for complete details on
this feature.
1. seTTing memOry PreseTs
To set a station: Select a frequency
band with the AM / FM button, then
select a station. Press and hold a
numbered preset button until the
sound returns.
2. TexT / scan FuncTiOn
Press and hold for a brief sampling
of radio stations or CD tracks. Press
again to stop. In CD / MP3 mode,
press and release to display track
title, artist name, disc title and file
name (if available).
3. am / Fm and cd selecT
In radio mode, press AM/FM to
select AM,FM1 or FM2 frequency
bands. Press CD to begin CD play.
In CD mode, press AM / FM to stop
play and begin radio play.
4. On / OFF / VOlume cOnTrOl
Press to turn ON or OFF. Turn to increase
or decrease volume.
5. lOading cds
Press the LOAD button and then a
preset number to load a CD. Press
and hold LOAD to autoload up to
6 CDs.
6. ejecTing cds
Press to eject a CD. For the In-dash
Six CD / MP3 system, press and
hold to auto-eject all CDs present in
the system.
7. seeK FuncTiOn
Press to access the next listenable
station or CD track.
8. saTelliTe radiO Fea Tures
and c OnTrOls
(if equipped)
AUX: Press to cycle through
FES/DVD (if equipped), SAT1, SAT2,
SAT3 (satellite mode if equipped) or
LINE IN (auxiliary mode if equipped).
Once Satellite Radio mode is
activated you may use the following
functions: Press MENU until
CATEGORY MODE appears in the
display. Press up/down arrows to
select from various categories of
music (country, rock, etc.) Press
SEEK to select a category. Press
SEEK again to search for channels
playing that specific category of
music. Press SEEK to access the
previous / next channels. Press and
release TEXT/ SCAN to display the
current song title. Press again to
scroll through current song title,
artist, channel category and the
SIRIUS long channel name. Press
and hold for a brief sampling of the
next channels. Press again to stop.
9. Tune / disc selecTOr
Press to go up or down the radio
frequency or to select a desired
disc. Also, use in menu mode to
select various settings.
10. muTe mOde
Pressing the MUTE button will mute
the playing media. Pressing it again
will return to the playing media.
11. sPeed sensiTiVe VOlume
This audio system is equipped with
speed sensitive volume. The volume
automatically changes slightly with
vehicle speed to compensate for
road and wind noise. Press MENU to
access and use SEEK to adjust.
SETTING THE CLOCK: Press MENU
until SELECT HOUR or SELECT MINS
is displayed. Press up/down arrows,
SEEK to adjust the hours / minutes.
12. shuFFle FuncTiOn shuFFle
Plays tracks in random order.
13. FOlders
Press to access previous or next
folder on MP3 discs, if folders
are available.
If your vehicle is equipped with a
different radio refer to your Owner’s
Guide. If your vehicle is equipped
with a navigation system, please
refer the navigation supplement.
duAl AutoMA tiC teMpeRA tuRe ContRol (dA tC) systeM
a. auTO
To engage automatic temperature
control, press AUTO and select
the desired temperature using the
temperature control. The system will
automatically determine fan speed,
airflow location, A/C on or off, and
outside or recirculated air to heat or
cool the vehicle, allowing it to reach
the desired temperature.
b. driVer/Passenger
TemPera Ture cOnTr Ol

Press to Increase or decrease the
temperature in the cabin.
c. exT
Press to display outside
temperature. Press again to
display cabin temperature settings.
d. Fan sPeed cOnTr Ol
Press to Increase or decrease
the fan speed.
e. heaTed sea T cOnTr Ols
Press to turn the heated seats on
and off. The heated seats
automatically turn off after 15
minutes, or when the ignition is
turned off.
F. manual OVerride c OnTr O l
Allows you to manually select where
airflow is directed. To return to full
automatic control, press AUTO.
g. a/c c OnTrOl
Press to activate/deactivate air
conditioning. Use with recirculated
air to improve cooling performance
and efficiency. Engages automatically
in AUTO, (defrost) and
(floor/defrost).
h. recircula TiOn cOnTrOl
Recirculates air in the cabin, thereby
reducing the amount of time needed
to cool down the interior of the
vehicle when used with A/C.
i. dual: (single/dual electric
temperature control)
Allows the driver to have full control
of the cabin temperature settings
(single zone) or allows the
passenger to have control of their
individual temperature settings (dual
zone control). Press to turn on dual
zone mode, press again to return to
single zone.
j. heaTed mirr Ors
Press to defrost the outside rear
view mirrors. The heated mirrors
will turn off after 10 minutes or can
be shut off by pressing the button
again. Please refer to Power Mirrors
in the Driver Controls chapter of your
Owner’s Guide for more information.
K. deFrOsT
Use to clear ice or fog from the
windshield by distributing air through
the windshield defroster and
demister vents.
max a/c OPera TiOn
Automatic Operation: Press AUTO
for full automatic operation. Do not
override A/C or recirculated air.
Set the temperature to 60˚F
(15.5˚C). Override Operation: Select
air distribution. Select A/C and
recirculated air. Use recirculated air
with A/C to provide colder airflow.
Set temperature to 60˚F (15.5˚C).
Set to highest front fan speed
initially, then adjust to
maintain comfort.
raPid heaT
Tm suPPlemenT al
inTeriOr hea Ter
(if equipped)
If your vehicle is equipped with a
diesel engine, it may be equipped
with a supplemental heater to assist
in heating the inside of your vehicle
in cold weather. When you start your
vehicle and turn the climate control
on and the engine coolant
temperature is below a preset level,
the supplemental heater will
automatically activate to aid the
climate control system in heating
your vehicle more quickly.
The supplemental heater is most
effective when using a mid to lower
fan speed setting.
For complete details on these and
other climate control features or
if your vehicle is equipped with a
climate control system other than
the one shown, please refer to your
Owner’s Guide.
4
3
3
2
1
69
13
13
87
12
11
B
A
DEGHEI
C
10
K
B
J
5
F
Ford Motor Company Customer Relationship CenterP.O. Box 6248 | Dearborn, MI 481211-800-392-3673 (FORD)(TDD for the hearing impaired: 1-800-232-5952)
This Quick Reference Guide is not intended to replace your vehicle Owner\
’s Guide which contains more detailed information concerning the features of your vehicle, as well as\
important safety warnings designed to help reduce the risk of injury to you and your occupants. Please read yo\
ur entire Owner’s Guide carefully as you begin learning about your new vehicle and refer to the appropriate c\
hapters when questions arise.
All information contained in this Quick Reference Guide was accurate at \
the time of duplication. We reserve the right to change features, operation and/or functionality of any vehi\
cle specification at any time. Your Ford dealer is the best source for the most current information. For detailed\
operating and safety information, please consult your Owner’s Guide.
October 2006First PrintingQuick Reference GuideSuper DutyLitho in U.S.A.
8 C 3 J - 1 9 G 2 1 7 - A A
*8C3J19G217AA*
Audiophile in-dAsh six Cd/Mp3/sA tellite CoMpAtible sound systeM (if equipped) duAl AutoMAtiC teMpeRA tuRe ContRol (dA tC) systeM WITH HEATED SEATS AND HEATED MIRRORS (if equipped)

ON and START, or by applying the
parking brake when the ignition
is turned to the ON position. If the
brake system warning light does not
illuminate at this time, seek service
immediately from your authorized
dealer. Illumination after releasing the
parking brake indicates low brake fluid
level and the brake system should be
inspected immediately by your
servicing authorized dealer.
5. a uTOlamPs (if equipped)
The autolamp system provides light
sensitive automatic on-off control of
the exterior lights normally controlled
by the headlamp control. The
autolamp system also keeps the lights
on for approximately 20 seconds. On
vehicles equipped with a message
center, you can select a delay from
0–180 seconds, after the ignition
switch is turned to OFF. To turn
autolamps on, rotate the control
counterclockwise. To turn autolamps
off, rotate the control clockwise to OFF.
6. FOglamPs (if equipped)
The headlamp control operates the
foglamps. The foglamps can be turned
on when the headlamp control is in
the , or and position
and the high beams are not turned on.
7. sPeed c OnTrOl
To operate, press the ON button. To
set a speed, press SET +. To set a
higher speed, press SET +. To set a
lower speed, press SET -. To disengage
speed control, press the brake pedal
or press OFF. Pressing RES will return
to a previously set speed as long as
the speed control was not turned off.
serVice inTerV
als
It is important to maintain your vehicle to keep it running in peak condition. Engine oil and filter changes along with fuel filter (two fuel filters on diesel vehicles) and engine coolant inspection/replacement are common maintenance items that can be done to prolong the life of your engine. If you drive your vehicle in severe situations, more frequent service will be required on some items. Please refer to the scheduled maintenance information chapter of your diesel supplement if your vehicle is equipped with a diesel engine or the separate Scheduled Maintenance Guide if your vehicle is equipped with a gasoline engine.
engine Fan OPera TiOn
Your vehicle is equipped with a high performance clutched cooling fan. When the clutch engages, the fan spins faster to provide more air to cool the engine. This typically occurs when carrying heavy loads, towing a trailer or with high outside temperatures. As fan speed increases (and as the clutch engages), you may notice an increase in fan noise which is normal. When extra cooling is no longer
required, the clutch disengages and the noise will go away. In most everyday driving conditions, the fan spins slower and the clutch is not engaged; this improves fuel economy and reduces fan speed/noise.
cOld wea Ther sTar Ting
It is recommended that the engine block heater be used for starting when the temperature is -10°F (-23°C) or colder. Please refer to Using the engine block heater (if equipped) in the Driving chapter of your Owner’s Guide.
diesel engine OPera TiOn
(if equipped)Diesel Engines have different starting and operating procedures than gasoline engines. Please refer to your diesel supplement for detailed information on starting and operating your diesel engine. Key items to remember are:
Starting the Engine With the key in the ON position, the light will illuminate if glow plug heat is necessary as a starting aid. Wait for the light to extinguish before starting the engine.
Turning Off the Engine It is important to remember that if you have been operating your vehicle at a high speed or maximum gross vehicle weight, it is recommended to let the engine idle for 3-5 minutes so the turbocharged engine can properly cool down.
Ultra Low Sulfur Diesel (ULSD) Fuel The diesel engine requires ultra low sulfur diesel fuel to control exhaust emissions, especially when combined with an after treatment device such as a Diesel Particulate Filter (DPF). It is always important to make sure the proper fuel is used because use of improper fuel (i.e. high level of biodiesel fuel or a high sulfur diesel fuel) may cause serious engine damage. Use of biodiesel is acceptable as long as the content is no higher than 5% (B5). If the biodiesel is rated higher than B5 (such as B10 or B20), it may damage fuel system components.
Exhaust System To control exhaust emissions, your diesel Super Duty is equipped with an exhaust system with clean diesel after-treatment technology which includes
a diesel oxidation catalytic converter and a diesel particulate filter (DPF). Warning: Modification(s) to or removal of any exhaust system parts could result in elevated exhaust temperature which may cause vehicle or property damage or personal injury and may void your vehicle’s warranty.
Draining the Water Separator Remember to drain the water separator monthly. Water will gather in the frame-mounted water separator, called the horizontal fuel conditioning module (HFCM). A WATER IN FUEL indicator will illuminate in the message center when the module has reached its capacity.
Checking the Air Filter Your vehicle has an air filtration system with a restriction indicator gauge that will alert you when you need to
change your filter. The gauge has a viewable indicator
located underhood on the air filter assembly which should
be inspected every 10,000 miles (16,000 km) or at every
oil change. A CHECK AIR FILTER message will also appear
in the message center when the system restriction reaches
its upper limit for proper operation. Always use the underhood air filter restriction gauge to determine when the air filter element needs to be changed.
Engine Oil Specifications for Diesel-Engines
youR 2008 FoRd
56
1
2
3
4
781715161812
Use Motorcraft oil or an equivalent oil conforming to Ford specification WSS-M2C171–E or API service categories CJ-4 or CJ-4/SM. It is important to use these oils because they are compatible with the emission control equipment of your vehicle to meet the more stringent emission standards.
Under normal conditions, the engine oil and filter need to be changed at 10,000 miles or 6 month intervals (whichever comes first). Under severe conditions, the intervals are sooner; 5,000 miles or 3 months (whichever comes first). Refer to the scheduled maintenance information chapter of the diesel owner guide supplement for specific information on normal and severe conditions.Use the same engine oil and filter change intervals when using synthetic engine oil.
Heavier 15W-40 and 5W-40 engine oils are recommended for temperatures over 50˚F (10˚C) and must be used for heavy duty driving and trailer towing.
fully-integrated electronic Trailer
Brake Controller (TBC). When used
properly, the TBC helps ensure
smooth and effective trailer braking
by powering the trailer’s electric
brakes with a proportional output
based on the towing vehicle’s brake
pressure. Using a digital display and
a few controls, trailer brake
adjustment can be performed and
monitored from inside the vehicle.
Your vehicle’s message center
interfaces with the TBC to alert you
to any concerns between the trailer
connection and your vehicle or the
TBC itself.
17. uPFiTTer
(auxiliary switched input box)
If your vehicle is equipped with
the Upfitter package, the four
auxiliary switches mounted on the
instrument panel can be
customized to perform additional
functions. The switches deliver 10A
or 30A of battery power to whatever
accessory is chosen. Refer to the
Body Builder’s Book or visit
www.fleet.ford.com/truckbbas/non-
html/Q117.pdf for more detailed
information on the Upfitter package.
18. a uxiliary PO wer POinTs
All vehicles are equipped with a
power point on the instrument panel;
SuperCab and Crew Cab models
have an additional power point on
the rear of the center console (if
equipped). A power point is designed
for accessory plugs only; do not
insert any other object as damage
may occur and blow the fuse.
19. a uxiliary inPuT jac K
(if equipped)
Your vehicle may be equipped with
an Auxiliary Input Jack (AIJ). The
Auxiliary Input Jack provides a way
to connect your portable music
player to the in-vehicle audio system.
This allows the audio from the
portable music player to be played
through the vehicle speakers with
high fidelity.
PO wer FOlding/PO wer

Telesc OPing OuT side mirrOrs

(if equipped)
If your vehicle is equipped with
power folding/power telescoping
mirrors, both
mirrors can
be folded
or unfolded
simultaneously
by using the power mirror switch
located on the driver’s door armrest.
Rotate the switch to the neutral
position and then pull the switch
rearward to pull the mirrors in.
Pull the switch rearward again to
return the mirrors
back to the normal
position. When
power folding the
trailer tow mirrors,
it is normal to
hear the sound
of the high
output motors.
The passenger
mirror will typically
complete folding
before the driver
mirror (this is
normal). If the
mirrors are manually
folded forward (pointing toward
the front of the vehicle), they
must be manually folded back
to the normal position for the
power fold feature to work.
Note: Power fold mirrors cannot
unfold while the vehicle is traveling
at highway speeds due to wind force
on the mirrors.
Both mirrors can be extended
simultaneously by using the
switch on the door trim panel.
To telescope the mirrors outward,
press and hold the left side of the
switch until they reach the desired
position. To retract the mirrors
inward, press and hold the right side
of the switch until the mirrors reach
the desired position. Please refer to
your Owner’s Guide for more details.
8. message cenTer
When the ignition is in the ON
position, the message center on
your vehicle’s instrument cluster will
display information on your vehicle’s
operating functions, as well as
warning messages. Pressing the INFO
button lets you scroll through general
vehicle information such as odometer,
trip odometer, compass, average fuel
economy, distance to empty (fuel) and
engine hours. Engine hours register
how many hours the engine has been
running. This is especially important if
your vehicle is equipped with a diesel
engine as important maintenance
items (engine oil changes and fuel
filter changes) may be based on
engine hours. Please refer to the
scheduled maintenance
information in your diesel
supplement for more information.
9. clima Te cOnTr Ol and audiO
Refer to the Climate Control and
Audio section on the reverse side
of this Quick Reference Guide.
10. PO wer rear sliding wind Ow
Push the switch,
(located behind
the steering wheel)
to open the rear
window. Pull to
close the rear window. Please refer to
your Owner’s Guide for more details.
11. TO w/haul swiT ch
To eliminate excessive transmission
shifting, activate the Tow/Haul
feature. This will reduce frequency
of transmission shifting and assist
in transmission cooling. This feature
also provides engine braking in all
forward gears when the transmission
is in the D (Overdrive) position; the
engine braking will slow the vehicle
and assist the driver in controlling the
vehicle when descending a grade.
12. FOur- wheel driVe
(4wd) s ysTem
(if equipped)
The 4WD system indicator lights
illuminate only under the following
conditions. If these lights illuminate
when driving in 2WD, contact your
authorized dealer as soon as possible.
• 4x4 HIGH – momentarily

illuminates after the engine
is started. Illuminates when
4H (4x4 High) is engaged.
• 4x4 LOW – momentarily

illuminates when the ignition
is turned to the ON position.
Illuminates when 4L (4x4 Low)

is engaged.
2H/2WD – For general on-road
driving. Sends power to the rear
wheels only.
4H/4x4 High – For winter and off-road
conditions. Sends power to front
and rear wheels. This mode is not
intended for use on dry pavement.
N (Neutral) (MSOS only) – Only used
when towing the vehicle. The transfer
case neutral position overrides the
transmission and puts the vehicle in
neutral regardless of the transmission
gearshift lever position. The vehicle
can move forward or backwards.
4L/4x4 Low – For low-speed off-road
applications that require extra power
such as steep grades, deep sand or
pulling a boat out of the water. Sends
power to the front and rear wheels.
This mode is not intended for use on
dry pavement. Ideal Shift Conditions:
Slow to 2-3mph, keep your foot on
the brake and shift transmission to
NEUTRAL. Select 4Low ( Some noise
is normal during shift). Once the 4Low
light is illuminated shift transmission
back into gear.
13. TracTiOn c OnTrOl sys Tem
Helps you maintain the stability and
steerability of your vehicle, especially
on slippery road surfaces such as
snow or ice-covered roads. This
system will allow your vehicle to make
better use of available traction in
these conditions. Push the button to
disable the traction control system
when desired.
14. POwer adjus Table
FOOT Pedals
(if equipped)
The accelerator and brake pedals
can be adjusted toward or away from
you for enhanced driving comfort.
The adjustable pedal position can
also be recalled with the memory
feature (if equipped). Please refer to
your Owner’s Guide for more details.
15. reVerse sensing sys Tem
(if equipped)
Sounds a tone to warn the driver of
obstacles up to 6 feet (2 meters)
from the rear bumper when the
R (Reverse) gear is selected and
the vehicle is moving at speeds
less than 3 mph (5 km/h). Push
the button to disable the reverse
sensing system when desired.
16. Trailer braKe cOnTr Oller
Your vehicle may be equipped with
an instrument panel-mounted
913919
1. serVice engine sOOn l amP
The Service engine soon indicator
light illuminates when the ignition
is first turned to the ON position to
check the bulb. Solid illumination
after the engine is started indicates
the On Board Diagnostics System
(OBD-II) has detected a malfunction.
Please refer to On board diagnostics
(OBD-II) in the Maintenance and
Specifications chapter of the Owner’s
Guide. If the light is blinking, engine
misfire is occurring which could
damage your catalytic converter.
Drive in a moderate fashion (avoid
heavy acceleration and
deceleration) and have your vehicle
serviced immediately.
2. abs w arning l amP
If the ABS light stays illuminated or
continues to flash, a malfunction
has been detected, have the system
serviced immediately. Normal braking
is still functional unless the brake
warning light is also illuminated.
3. airbag readiness l amP
If this light fails to illuminate when
ignition is turned to ON, continues to
flash or remains on, have the system
serviced immediately. A chime will
also sound when a malfunction in the
supplemental restraint system has
been detected.
4. braKe s ysTem w arning l amP
To confirm the brake system warning
light is functional, it will momentarily
illuminate when the ignition is turned
to the ON position, when the engine is
not running or in a position between
111014