clock FORD TAURUS 1996 User Guide

278 [SV18300(ALL)11/94]
RWARNING
Never remove the pressure cap while the
engine is running or hot to avoid personal
injury that can be caused by escaping
steam or engine coolant.
[SV18500(ALL)04/95]
1. Before you remove the cap, turn the engine
off and let it cool. Even when the engine is
cool, be careful when you remove the cap.
[SV18600(ALL)02/95]
2. When the engine is cold, wrap a thick cloth
around the cap and turn it slowly
counterclockwise to relieve pressure.
*
[SV18700(ALL)09/95]
3. Step back while the pressure releases.
*
[SV18800(ALL)09/95]
4. When you are sure that all the pressure has
been released, use the cloth to turn and
remove cap.
*
[SV18900(ALL)02/95]
5. Stand away from the reservoir opening. Hot
steam may blow out or hot engine coolant
may even splash out.
*
[SV19000(ALL)09/95]
RWARNING
Failure to follow these instructions could
result in serious personal injury from hot
engine coolant or steam blowout and/or
damage to the engine cooling system or
engine.
*
[SV19050(ALL)09/95]
To find out how much engine coolant mixture
your vehicle's coolant system can hold, seeRefill
capacities for fluidsin the Index.
[SV19100(ALL)04/95]
Add engine coolant only to the coolant
reservoir.If the coolant level is low, add to the
reservoir a 50/50 mixture of water and the type
of engine coolant that Ford specifies. You may
add water by itself only in an emergency, but
you should replace it with a 50/50 mixture as
soon as possible.
File:15fcsvt.ex
Update:Tue Jan 23 13:58:51 1996
ProCarManuals.com

315
*
[SV39501(ALL)02/95]
4. Remove the bulb retaining ring by rotating it
counterclockwise (when viewed from the
rear) about an eighth of a turn to free it
from the bulb socket, and by sliding the ring
off the plastic base. Keep the ring. It is to be
used again to retain the new bulb.
[SV39550(ALL)02/95]
5. Carefully remove the bulb from its socket by
gently pulling it straight back out of the
socket. Do not turn the bulb while you
remove it.
*
[SV39601(ALL)03/95]
To install a bulb:
*
[SV39650(ALL)02/95]
1. With the flat side of the bulb's plastic base
facing upward, insert the glass end of the
bulb into the socket. You may need to turn
the bulb left or right to line up the grooves
in the plastic base with the tabs in the
socket. When the grooves are aligned, push
the bulb into the socket until the plastic base
contacts the rear of the socket.
*
[SV39701(ALL)08/95]
2. Slip the bulb retaining ring over the plastic
base until it contacts the rear of the socket.
Lock the ring into the socket by rotating it
clockwise until you feel a ªstop.º
*
[SV39750(ALL)02/95]
3. Push the electrical connector into the rear of
the plastic base until it snaps, locking it into
position.
*
[SV39800(ALL)02/95]
4. Turn the headlamps on and make sure that
they work properly. If the headlamp was
correctly aligned before you changed the
bulb, you should not need to align it again.
File:15fcsvt.ex
Update:Tue Jan 23 13:58:51 1996
ProCarManuals.com

318
*
[SV40501(ALL)06/95]
Vertical aim adjustment
[SV40601(ALL)04/95]
1. With the hood open, locate the bubble level
vertical aim indicator. It is visible when
viewed from above and to the rear of the
headlamp.
[SV40650(ALL)04/95]
2. With the vehicle on a level surface, use a
4mm wrench to turn the vertical aim
adjustment screw (outboard screw) located
on the back of the lamp assembly clockwise
or counterclockwise until the bubble in the
spirit level is centered when viewed from
directly above the bubble.
[SV40725(ALL)04/95]
3. Close the hood.
[SV40750(ALL)06/95]
If the vehicle is on a downward or upward
slope of not more than1.2Ê, theVHAD's bubble
level can be used to correct for the effects of the
surface slope, provided that the slope is
accurately known.
[SV40775(ALL)06/95]
Each graduation of the bubble level represents
0.19Ê ofdownward or upward slope. To correct
for the effects of a surface slope, turn the
vertical aim adjustment screw until the bubble is
centered at a position corresponding to the slope
of the surface.
[SV40800(ALL)02/95]
Each 0.1 inch difference in surface height
between the front and the rear wheels
corresponds to0.053Ê ofsurface slope; each0.19Ê
of surface slope corresponds to 0.36 inches
difference in surface height between the front
and rear wheels.
File:15fcsvt.ex
Update:Tue Jan 23 13:58:51 1996
ProCarManuals.com

Index 361
Cleaning your vehicle (continued)
exterior lamps............ 108
fabric................ 151
headlamps.............. 108
instrument panel............ 91
interior............... 151
interior lamps............ 113
mirrors............... 154
plastic parts.............. 7
polishing................ 6
rear windows............ 105
rustproofing.............. 7
safety belts............... 23
tail lamps.............. 108
upholstery and interior trim...... 151
washing................ 6
waxing................ 6
wheels................ 295
windows............... 105
Climate control system
electronic automatic
temperature control.......... 95
manual heating and air conditioning . . . 93
Clock................. 113
Cold engine starting............ 62
Combination lap and shoulder belts.... 12
Compact disc player (see Electronic
sound system)............ 182
Console, description........... 156
Controls
instrument panel............ 91
mirrors............... 153
steering column........... 115
File:fcixt.ex
Update:Tue Jan 23 08:18:16 1996
ProCarManuals.com