clock FORD TAURUS 1996 Owners Manual

91
Instrument Panel Controls
[IP00400(ALL)05/95]
The main controls for the climate control system,
clock, and radio are in the oval Integrated
Control Panel on the instrument panel.
[IP00410(ALL)04/95]
The controls for the lights and climate control air
registers are also on the instrument panel.
*
[IP00420(ALL)03/95]
Clean the instrument panel lens and woodtone
trim with a soft cloth and a glass cleaner. Do
not use paper towel or any abrasive cleaner to
clean either the lens or the woodtone trim as
these may cause scratches.
%*
[IP00430(ALL)09/95]
NOTE: Any cleaner or polish that increases the
gloss (shine) of the upper part of the
instrument panel should be avoided.
The dull finish in this area is to help
protect the driver from undesirable
windshield reflection.
File:06fcipt.ex
Update:Tue Jan 23 08:13:16 1996
ProCarManuals.com

113 %
*
[IP31200(ALL)04/95]
Cleaning the Interior Lamps
*
[IP31300(ALL)04/95]
Your interior dome lamps and map lamps are
plastic and should be cleaned with a mild
detergent diluted in water. Rinse them with clear
water.
%*
[IP31400(ALL)01/95]
Battery Saver
[IP31500(ALL)11/94]
When the ignition is turned off, the vehicle will
turn off battery voltage to the interior lights
after 40 minutes.
*
[IP31600(ALL)09/95]
This will prevent draining of the battery if those
lights have been left on inadvertently or if a
door is not completely closed. Battery voltage to
these lamps will be restored when the outside
front door handles are lifted, the keyless entry
keypad is used, the remote entry transmitter is
used, any door is opened, the trunk is opened,
or the ignition key is turned to the ON position.
%
*
[IP32600(ALL)03/95]
Clock
[IP33200(ALL)03/95]
quarter page art:0000247-G
The digital clock
*
[IP33750(ALL)05/95]
1. To set the hour, press and hold the hour
button. When the desired hour appears,
release the button.
*
[IP33850(ALL)05/95]
2. To set the minutes, press and hold the
minute button. When the desired minute
appears, release the button.
File:06fcipt.ex
Update:Tue Jan 23 08:13:16 1996
ProCarManuals.com

192 %
*
[DR03800(ALL)01/95]
Putting Your Vehicle in Gear
*
[DR04001(ALL)05/95]
RWARNING
Hold the brake pedal down while you
move the gearshift lever from position to
position. If you do not hold the brake
pedal down, your vehicle may move
unexpectedly and injure someone.
*
[DR04050(ALL)03/95]
To operate:
*
[DR04101(ALL)01/95]
1. Start the engine.
*
[DR04150(ALL)01/95]
2. Depress and hold the brake pedal.
*
[DR04201(ALL)01/95]
3. Move the gearshift lever out of P (Park).
%*
[DR04250(ALL)04/95]
Your vehicle is equipped with a Brake Shift
Interlock safety feature. This feature prevents the
gearshift from being moved from the P (Park)
position until the brake pedal is depressed. This
feature is active when the ignition is in the ON
position. If the gearshift lever CANNOT be
moved from P (Park) with the brake pedal
depressed:
*
[DR04300(ALL)01/95]
1. Turn the engine off and remove the ignition
key.
[DR04350(ALL)11/94]
2. Reinsert the ignition key and turn clockwise
to the first position (OFF).
[DR04400(ALL)11/94]
3. Depress the brake pedal, move the gearshift
lever to N (Neutral) and start the engine.
*
[DR04425(ALL)07/95]
If you need to shift out of P (Park) by using the
alternate procedure described above, it is
possible that a fuse has blown and that your
brakelamps may also not be functional. Please
refer to the chapter titledServicing Your Taurus
in this Owner Guide for instructions on checking
and replacing fuses.
File:10fcdrt.ex
Update:Mon Jan 22 15:59:33 1996
ProCarManuals.com

196
*
[DR06745(ALL)03/95]
To operate:
*
[DR06750(ALL)01/95]
1. Start the engine.
*
[DR06755(ALL)01/95]
2. Depress and hold the brake pedal.
*
[DR06760(ALL)01/95]
3. Move the gearshift lever out of P (Park).
%*
[DR06765(ALL)04/95]
Your vehicle is equipped with a Brake Shift
Interlock safety feature. This feature prevents the
gearshift from being moved from the P (Park)
position until the brake pedal is depressed. This
feature is active when the ignition is in the ON
position. If the gearshift lever CANNOT be
moved from P (Park) with the brake pedal
depressed:
*
[DR06770(ALL)01/95]
1. Turn the engine off and remove the ignition
key.
[DR06775(ALL)11/94]
2. Reinsert the ignition key and turn clockwise
to the first position (OFF).
[DR06780(ALL)11/94]
3. Depress the brake pedal, move the gearshift
lever to N (Neutral) and start the engine.
*
[DR06781(ALL)07/95]
If you need to shift out of P (Park) by using the
alternate procedure described above, it is
possible that a fuse has blown and that your
brakelamps may also not be functional. Please
refer to the chapter titledServicing Your Taurus
in this Owner Guide for instructions on checking
and replacing fuses.
*
[DR06783(ALL)09/95]
RWARNING
DO NOT DRIVE YOUR VEHICLE UNTIL
YOU VERIFY THAT THE BRAKELAMPS
ARE WORKING.
File:10fcdrt.ex
Update:Mon Jan 22 15:59:33 1996
ProCarManuals.com

226 [RE07700(ALL)07/95]When one of the front wheels is off the ground,
the transaxle alone will not prevent the vehicle
from moving or slipping off the jack, even if the
vehicle is in P (Park). To prevent the vehicle
from moving when you change a tire, block (in
both directions) the wheel that is diagonally
opposite to the tire being changed.
*
[RE08400(ALL)09/95]
RWARNING
If the vehicle slips off the jack, you or
someone else could be seriously injured.
*
[RE08800(ALL)03/95]
2. Get out the spare tire and jack.
*
[RE08850(ALL)05/95]
RWARNING
To avoid injury, never run the engine
with one wheel off the ground, such as
when changing a tire.
% [RE08900(ALL)02/93]
3. Remove wheel covers or aluminum wheel
ornaments with the tapered end of a wheel
nut wrench. Insert the handle of the wrench
between the wheel and ornament and twist
it against the inner wheel cover flange.
*
[RE09200(ALL)09/95]
4. Loosen each wheel lug nut one-half turn
counterclockwise, but do not remove them
until the tire is raised off the ground. You
should pull up on the handle rather than
push to develop maximum force to loosen
wheel lug nuts. SeeAnti-Theft Wheel Lug
Nutslater in this chapter for information on
removing anti-theft lug nuts.
File:12fcret.ex
Update:Mon Jan 22 16:01:15 1996
ProCarManuals.com

227 %
*
[RE09250(ALL)05/95]
Removing and Replacing the Tire
%*
[RE09300(ALL)11/94]
1. Find the jack notch next to the door of the
tire that you are changing. Put the jack in
the jack notch and turn the handle of the
jack clockwise until the wheel is completely
off the ground.
*
[RE09500(ALL)05/95]
RWARNING
To lessen the risk of personal injury, do
not put any part of your body under the
vehicle while changing a tire. Do not start
the engine when your vehicle is on the
jack. The jack is only meant for changing
the tire.
[RE10000(ALL)02/95]
half page art:0000394-C
The notches for the jack
% [RE12000(ALL)11/94]
2. Remove the lug nuts by using a lug wrench.
Never loosen the hub nuts. See the picture
later in this section if you are not sure where
to find the lug nuts.
File:12fcret.ex
Update:Mon Jan 22 16:01:15 1996
ProCarManuals.com

228
*
[RE12002(ALL)08/95]
Your vehicle has metric (12 mm) wheel studs
and lug nuts. During wheel removal and
replacement, make certain that you use the same
lug nuts to reinstall the wheel or replace them
with nuts of the same metric size and threading.
*
[RE12005(ALL)08/95]
RWARNING
Installation of an English thread nut on a
metric stud (or vice-versa) will not
properly secure the wheel to the hub.
Damaged studs may result in wheel
separation and possible injury.
*
[RE12100(ALL)01/95]
3. Replace the flat tire with the spare tire,
making sure that the air valve stem is facing
outward.
*
[RE12200(ALL)03/95]
4. Reinstall the lug nuts, tightening until the
wheel is snug against the hub. The beveled
edges on the lug nuts face inward. Do not
fully tighten the lug nuts until you lower the
vehicle. If you do, you could force the
vehicle off the jack.
*
[RE12300(ALL)01/95]
5. Lower the vehicle by turning the jack handle
counterclockwise.
*
[RE12400(ALL)01/95]
6. Remove the jack and fully tighten the lug
nuts in the order shown in the following
illustration. As soon as possible, have your
dealer or a qualified service technician check
the lug nuts for proper torque specifications.
File:12fcret.ex
Update:Mon Jan 22 16:01:15 1996
ProCarManuals.com

233
*
[RE14400(ALL)03/95]
Removing the anti-theft lug nut
*
[RE14600(ALL)03/95]
Insert the key over the locking lug nut. Make
sure that you hold the key square to the lug nut.
If you hold the key on an angle, you may
damage the key and the lug nut.
*
[RE14700(ALL)03/95]
Place the lug nut wrench over the lug nut key
and apply pressure on the key with the wrench.
Turn the wrench in a counterclockwise direction
to remove the lug nut.
*
[RE14800(ALL)09/95]
Reinstalling the anti-theft lug nut
*
[RE14900(ALL)03/95]
Insert the key over the locking lug nut. Place the
lug nut wrench over the lug nut key and, while
applying pressure on the key, install the lug nut.
*
[RE15050(ALL)03/95]
If the Engine Cranks But Does
Not Start or Does Not Start After
a Collision
*
[RE15100(ALL)07/95]
The Fuel Pump Shut-off Switch
*
[RE15200(ALL)07/95]
If the engine cranks but does not start or if you
have had a collision, the fuel pump shut-off
switch may have been triggered. The shut-off
switch is a device that stops the fuel pump
when your vehicle has been involved in a
substantial jolt.
*
[RE15250(ALL)07/95]
For information on how to check and reset the
fuel pump shut-off switch, seeFuel pump shut-off
switchin the Index.
%
*
[RE16400(ALL)05/95]
Towing Your Vehicle
[RE16500(ALL)10/95]
If you need to have your vehicle towed, contact
a professional towing service or, if you are a
member, your roadside assistance center. Your
Taurus should be towed from the front unless
conditions do not allow it. It is recommended
that your vehicle be towed with wheel lift or
flatbed equipment.
File:12fcret.ex
Update:Mon Jan 22 16:01:15 1996
ProCarManuals.com

264 %
*
[SV05075(ALL)04/95]
Cleaning the Engine
*
[SV06000(ALL)07/95]
A clean engine is more efficient because the
engine is able to cool properly. A build up of
grease and dirt acts as an insulator, keeping the
engine warmer than normal.
*
[SV06020(ALL)07/95]
q
Extreme care must be used if a power washer
is used to clean the engine. The high pressure
fluid could penetrate sealed parts and
assemblies causing damage or malfunctions.
*
[SV06040(ALL)08/95]
q
In order to avoid possible cracking of the
engine block or fuel injection pump, do not
spray a hot engine or injection pump with
cold water.
*
[SV06060(ALL)07/95]
q
The alternator, distributor and air intake must
be covered. Covering these components will
help prevent water damage.
*
[SV06080(ALL)04/95]
q
Never wash or rinse the engine while it is
running. Water getting into the engine may
cause internal damage.
%
*
[SV06100(ALL)03/95]
Filling the Fuel Tank
[SV06800(ALL)04/95]
1. Turn the engine off. After opening the fuel
door, remove the cap carefully and slowly
by turning it counterclockwise 1/4 turn until
it stops. Pull to remove the cap. A tether
attaches the cap to the fuel filler pipe.
[SV06825(ALL)04/95]
one inch art:0001470-AFile:15fcsvt.ex
Update:Tue Jan 23 13:58:51 1996
ProCarManuals.com

265 [SV06850(ALL)04/95]
RWARNING
The fuel system may be under pressure. If
the fuel cap is venting vapor or if you
hear a hissing sound, wait until it stops
before completely removing the cap.
Otherwise, fuel may spray out and injure
you or others.
*
[SV06900(ALL)05/95]
2. Make sure that you pump unleaded fuel and
put the nozzle all the way inside the fuel
filler pipe.
[SV06950(ALL)09/95]
NOTE: To help reduce early nozzle shutoffs
and fuel spillage, park your vehicle so
that the fuel filler door is not
downhill. Do not tilt or turn the nozzle
upside down when filling. Avoid
excessively fast fuel dispensing rates
(over 10 gallons [38 liters] per minute).
*
[SV07150(ALL)08/95]
NOTE: If you spill any fuel on the body of
your vehicle, clean it off immediately.
The fuel may dull or soften the paint
if you do not wash it off.
[SV07200(ALL)10/95]
3. To replace the fuel cap, align the tabs on the
cap with the notches on the filler pipe. Turn
it clockwise until it stops.
*
[SV07250(ALL)10/95]
4. Push the fuel door closed.
[SV07275(ALL)04/95]
If the Service Engine Soon warning light comes
on and stays on when you start the engine, the
fuel cap may not be properly seated. Turn off
the engine, remove the fuel cap and replace it,
being careful to align the cap properly. For more
information, seeWarning lightsin the Index.
*
[SV07290(ALL)07/95]
If you lose the fuel cap, replace it with an
authorized Motorcraft or equivalent part.
File:15fcsvt.ex
Update:Tue Jan 23 13:58:51 1996
ProCarManuals.com