headlamp FORD TAURUS 1996 User Guide

116
*
[SC03200(ALL)05/95]
To turn off the high beams, pull the lever
toward you until it latches. The high beam
indicator light turns off.
%*
[SC03300(ALL)08/95]
Flashing the Lights
*
[SC03400(ALL)06/95]
To flash the headlamps, pull the lever toward
you for a moment and then release it. The
headlamps will flash whether the headlamp
knob is in the on or off position.
[SC03450(ALL)04/95]
one third page art:0001411-B
The turn signal lever
%*
[SC03500(ALL)08/95]
Windshield Wipers and Washer
*
[SC03600(ALL)03/95]
To turn on the windshield wipers, the ignition
key must be turned to the ON or ACC position.
[SC03900(ALL)05/94]
Turn the knob on the end of the turn signal
lever away from you to activate the wipers. The
first seven detents are interval wipe positions,
the eighth detent is the LO position, and the
ninth detent is the HI position.
*
[SC04000(ALL)01/95]
To turn the wipers off, turn the knob toward
you to the OFF position.
File:07fcsct.ex
Update:Mon Jan 22 15:52:32 1996
ProCarManuals.com

138 [FV08851(ALL)04/95]Illuminated Entry System
[FV08900(ALL)10/95]
This system will provide illumination of the
vehicle's interior courtesy lamps when either
outside driver's door keypad is pressed or when
the remote entry system is used to unlock the
door or sound the personal alarm. The system
will automatically turn off after approximately
25 seconds or when the ignition is turned to the
RUN or ACC position.
*
[FV08951(ALL)09/95]
NOTE: The inside lights will not turn off if
you have turned them on with the
dimmer thumbwheel or if any door is
open.
[FV09551(ALL)04/95]
Perimeter Anti-Theft System (If equipped)
*
[FV09600(ALL)05/95]
When armed, this system helps protect your
vehicle against break-ins or theft.
%*
[FV09651(ALL)05/95]
When an unauthorized entry occurs, the system
triggers and will:
*
[FV09700(ALL)02/95]
q
flash the headlamps, parking lamps, and theft
indicator lamp
*
[FV09751(ALL)06/95]
q
honk the horn
%*
[FV09801(ALL)05/95]
Arming the system
*
[FV09851(ALL)04/95]
The system is ready to arm any time the ignition
switch is turned OFF and the alarm is not
triggered or sounding. Any of the following
events will prearm the anti-theft system:
[FV09900(ALL)04/95]
q
Pressing the remote entry transmitter LOCK
button to lock the doors (with the doors open
or closed).
[FV09951(ALL)10/95]
q
Pressing the 7/8 and 9/0 buttons on the
Keyless Entry Keypad at the same time to
lock the doors (with the doors open or
closed).
File:08fcfvt.ex
Update:Mon Jan 22 15:57:12 1996
ProCarManuals.com

255
Servicing Your Taurus
%*
[SV00300(ALL)03/95]
Service Made Easy
*
[SV00400(ALL)01/95]
Ford has two goals for servicing your vehicle.
*
[SV00500(ALL)01/95]
1. When we can, we design parts that do not
need to be serviced.
*
[SV00600(ALL)01/95]
2. We want to make servicing your vehicle as
easy as possible. To help you:
*
[SV00700(ALL)01/95]
q
We highlight do-it-yourself items in yellow in
the engine compartment so that you can find
them easily.
*
[SV00800(ALL)01/95]
q
When possible, we design parts Ð such as
the headlamp bulbs Ð that can be replaced
without tools.
*
[SV00900(ALL)05/94]
q
We give you a Maintenance Schedule that
makes tracking routine service for your
vehicle easy. The maintenance schedule is
located in theMaintenance Schedule and Record
booklet.
*
[SV01000(ALL)01/95]
This chapter tells you about the basic parts that
you need to check and service regularly.
*
[SV01100(ALL)03/95]
If your vehicle needs professional servicing, see
theCustomer Assistancechapter.
*
[SV01200(ALL)03/95]
Check yourWarranty Information Bookletto find
out which parts are covered.
File:15fcsvt.ex
Update:Tue Jan 23 13:58:51 1996
ProCarManuals.com

312 [SV36250(ALL)04/95]
fourteen pica chart:0001468-A
*
[SV36300(ALL)08/95]
RWARNING
Always replace a fuse with one that has
the specified amperage rating. Using a
fuse with a higher amperage rating can
cause severe wire damage and could start
a fire.
[SV36400(ALL)11/94]
5. Put the cover back on.
*
[SV36600(ALL)01/95]
Even after you replace a fuse, it will continue to
blow if you do not find what caused the
overload. If the fuse continues to blow, have
your electrical system checked.
*
[SV37500(ALL)03/95]
The Lights
*
[SV37600(ALL)01/95]
It is a good idea to check the operation of the
following lights frequently:
*
[SV37700(ALL)01/95]
q
headlamps
*
[SV37800(ALL)01/95]
q
tail lamps
*
[SV37900(ALL)01/95]
q
brakelamps
*
[SV37950(ALL)02/95]
q
high-mount brakelamp
File:15fcsvt.ex
Update:Tue Jan 23 13:58:51 1996
ProCarManuals.com

313
*
[SV38000(ALL)01/95]
q
hazard flasher
*
[SV38100(ALL)01/95]
q
turn signals
*
[SV38200(ALL)01/95]
q
side markers
*
[SV38300(ALL)01/95]
q
license plate lamp
%*
[SV38400(ALL)01/95]
The alignment of your headlamps should be
checked if:
*
[SV38500(ALL)01/95]
q
oncoming motorists frequently signal you to
turn off your vehicle's high beams when you
do not have the high beams on
*
[SV38600(ALL)01/95]
q
the headlamps do not seem to give you
enough light to see clearly at night
*
[SV38700(ALL)11/92]
q
the headlamps are not aligned so that they
point slightly down and to the right.
%*
[SV38800(ALL)03/95]
Replacing the Headlamp Bulb
*
[SV38900(ALL)01/95]
The headlamps on your vehicle use replaceable
bulbs. When the lamp burns out, simply replace
the bulb, rather than the whole lamp.
*
[SV39000(ALL)05/95]
RWARNING
Handle a halogen headlamp bulb carefully
and keep out of children's reach. Grasp
the bulb only by its plastic base and do
not touch the glass. The oil from your
hand could cause the bulb to break the
next time the headlamps are operated.
*
[SV39100(ALL)01/95]
Do not remove the burned-out bulb unless you
can immediately replace it with a new one. If a
bulb is removed for an extended period of time,
contaminants may enter the headlamp housing
and affect its performance.
File:15fcsvt.ex
Update:Tue Jan 23 13:58:51 1996
ProCarManuals.com

314 [SV39250(ALL)11/92]
one third page art:0000345-AParts of a headlamp
*
[SV39300(ALL)03/95]
To remove the headlamp bulb:
*
[SV39350(ALL)05/95]
1. Make sure that the headlamp knob is in the
OFF position.
[SV39401(ALL)04/95]
2. Lift the hood. If you are replacing the
driver's side headlamp, unclip the electronic
module on the right side of the battery and
move it out of the way. Find the bulb in the
headlamp socket.
[SV39425(ALL)04/95]
one third page art:0001437-A
The module behind the driver's side headlamp
*
[SV39450(ALL)02/95]
3. Remove the electrical connector from the
bulb by pulling the connector.
File:15fcsvt.ex
Update:Tue Jan 23 13:58:51 1996
ProCarManuals.com

315
*
[SV39501(ALL)02/95]
4. Remove the bulb retaining ring by rotating it
counterclockwise (when viewed from the
rear) about an eighth of a turn to free it
from the bulb socket, and by sliding the ring
off the plastic base. Keep the ring. It is to be
used again to retain the new bulb.
[SV39550(ALL)02/95]
5. Carefully remove the bulb from its socket by
gently pulling it straight back out of the
socket. Do not turn the bulb while you
remove it.
*
[SV39601(ALL)03/95]
To install a bulb:
*
[SV39650(ALL)02/95]
1. With the flat side of the bulb's plastic base
facing upward, insert the glass end of the
bulb into the socket. You may need to turn
the bulb left or right to line up the grooves
in the plastic base with the tabs in the
socket. When the grooves are aligned, push
the bulb into the socket until the plastic base
contacts the rear of the socket.
*
[SV39701(ALL)08/95]
2. Slip the bulb retaining ring over the plastic
base until it contacts the rear of the socket.
Lock the ring into the socket by rotating it
clockwise until you feel a ªstop.º
*
[SV39750(ALL)02/95]
3. Push the electrical connector into the rear of
the plastic base until it snaps, locking it into
position.
*
[SV39800(ALL)02/95]
4. Turn the headlamps on and make sure that
they work properly. If the headlamp was
correctly aligned before you changed the
bulb, you should not need to align it again.
File:15fcsvt.ex
Update:Tue Jan 23 13:58:51 1996
ProCarManuals.com

316 %
*
[SV39850(ALL)02/95]
Aiming Headlamps
[SV39901(ALL)02/95]
Your vehicle is equipped with a Vehicle
Headlamp Aim Device (VHAD) on the
headlamp reflector extension and headlamp
housing. Each headlamp may be properly aimed
in the horizontal direction (left/right) and the
vertical direction (up/down) by performing the
steps outlined in the following paragraphs. The
horizontal aim must be adjusted first.
[SV39950(ALL)06/95]
Tools required: One 4mm box wrench or open
end wrench.
[SV40050(ALL)04/95]
Position the vehicle on a surface that is level on
the front-to-rear direction.
[SV40075(ALL)04/95]
If the vehicle cannot be placed on a true level
surface, the headlamps still can be adjusted
using the VHAD if the slope of the surface is
accurately known and does not differ by more
than1.2Êfrom true level. A difference of 2.27
inches in height of the surface between the front
and rear wheels corresponds to1.2Êslope.
[SV40100(ALL)04/95]
If the vertical adjuster is within +/s4
graduations about zero, the vertical headlamp
aim is within specification; and if the horizontal
adjuster is within +/s2 graduations about zero,
the horizontal headlamp aim is within
specification.
File:15fcsvt.ex
Update:Tue Jan 23 13:58:51 1996
ProCarManuals.com

318
*
[SV40501(ALL)06/95]
Vertical aim adjustment
[SV40601(ALL)04/95]
1. With the hood open, locate the bubble level
vertical aim indicator. It is visible when
viewed from above and to the rear of the
headlamp.
[SV40650(ALL)04/95]
2. With the vehicle on a level surface, use a
4mm wrench to turn the vertical aim
adjustment screw (outboard screw) located
on the back of the lamp assembly clockwise
or counterclockwise until the bubble in the
spirit level is centered when viewed from
directly above the bubble.
[SV40725(ALL)04/95]
3. Close the hood.
[SV40750(ALL)06/95]
If the vehicle is on a downward or upward
slope of not more than1.2Ê, theVHAD's bubble
level can be used to correct for the effects of the
surface slope, provided that the slope is
accurately known.
[SV40775(ALL)06/95]
Each graduation of the bubble level represents
0.19Ê ofdownward or upward slope. To correct
for the effects of a surface slope, turn the
vertical aim adjustment screw until the bubble is
centered at a position corresponding to the slope
of the surface.
[SV40800(ALL)02/95]
Each 0.1 inch difference in surface height
between the front and the rear wheels
corresponds to0.053Ê ofsurface slope; each0.19Ê
of surface slope corresponds to 0.36 inches
difference in surface height between the front
and rear wheels.
File:15fcsvt.ex
Update:Tue Jan 23 13:58:51 1996
ProCarManuals.com

358 Index
Anti-theft lug nuts and key........ 232
Anti-theft system
arming the system.......... 138
triggering.............. 138
Appeals (see Dispute settlement board) . . 240
Assistance (see Customer assistance).... 237
Audio system
(see Electronic sound system)..... 169
Autolamp system (see Headlamps).... 108
Automatic transaxle
driving with...........191, 195
fluid, adding............. 298
fluid, checking............ 296
fluid, refill capacities......... 328
fluid, specification........... 330
Axle
lubricant specifications......... 330
refill capacities............ 328
B
Backing up.............193, 198
Basic vehicle warranty........... 4
Battery
acid, treating emergencies....... 217
battery saver............. 113
charging system warning light...... 74
disconnecting............. 282
jumping a disabled battery....... 217
proper disposal, recycling....... 283
replacement, specifications....... 329
servicing............... 282
when storing your vehicle....... 333
Brake fluid
brake warning light........... 73
checking and adding......... 298
description.............. 298
specifications............. 330
File:fcixt.ex
Update:Tue Jan 23 08:18:16 1996
ProCarManuals.com