engine FORD TAURUS 1996 Owner's Manual

84 %
*
[LG09800(ALL)01/95]
Speedometer
*
[LG09900(ALL)01/95]
The speedometer tells you how many miles
(kilometers) per hour your vehicle is moving.
%*
[LG10000(ALL)01/95]
Odometer
*
[LG10100(ALL)01/95]
The odometer tells you the total number of miles
(kilometers) your vehicle has been driven.
%*
[LG10200(ALL)11/94]
Trip Odometer
*
[LG10300(ALL)11/94]
The trip odometer tells you how many miles
(kilometers) your vehicle has been driven since
the last reset. Press the reset button to return the
trip odometer to zero.
%*
[LG10320(ALL)02/95]
Tachometer
[LG10340(ALL)02/95]
The tachometer tells you the approximate engine
revolutions per minute (how fast the engine is
running). You may damage the engine if you
drive with the indicator in the red zone.
% [LG10350(ALL)12/95]The Optional and SHO Clusters
[LG10360( T)02/95]
The optional cluster and the SHO cluster have
indicator lights that are not on the standard
cluster. For details about these lights, read the
information below. To learn about the standard
warning lights and gauges that come on all
clusters, seeThe Standard Clusterearlier in this
chapter.
[LG10365( T)12/95]
The optional cluster has a 120 mph (200 km/h)
speedometer and a 7,000 rpm tachometer.
[LG10370( T)02/95]
The SHO cluster also has a 150 mph (240 km/h)
speedometer and an 8,000 rpm tachometer.
File:05fclgt.ex
Update:Tue Jan 23 08:14:15 1996
ProCarManuals.com

87 [LG14750(ALL)12/95]
Low Coolant Light and Chime
[LG14850(ALL)04/95]
This light indicates that the level of the engine
coolant is low inside the coolant reservoir.
[LG14950(ALL)04/95]
one inch art:0000114-C
Low coolant light
[LG15000(ALL)12/95]
This light comes on for a few seconds when
your ignition key is turned to the ON position,
but should turn off when the engine starts. If the
coolant is low, the light will come on and a
single chime will sound. If this light stays on,
check the level of coolant inside the coolant
reservoir. For instructions on adding coolant
mixture, seeEngine coolantin the Index.
% [LG15150(ALL)12/95]
Low Washer Fluid Light
*
[LG15250(ALL)02/95]
This light comes on if the reservoir is less than a
quarter full when you turn on the windshield
washers.
[LG15350(ALL)04/95]
one inch art:0000118-B
Low washer fluid light
% [LG16100(ALL)12/95]
Rear Lamp Out Indicator
[LG16200(ALL)12/95]
This light indicates that a rear tail lamp or
brakelamp is not functioning. It comes on
momentarily when the ignition is turned to the
ON position, then goes out.
File:05fclgt.ex
Update:Tue Jan 23 08:14:15 1996
ProCarManuals.com

99 [IP05650(ALL)10/95]
Changing the display from farenheit to
celsius
[IP05675(ALL)10/95]
To change the temperature display from
Farenheit to Celsius, depress the MAX A/C and
VF-DEF at the same time and hold them
down for about a second. To change back to the
original setting, repeat the process. If the battery
is disconnected, the display will revert to
Fahrenheit and must be reset to Celsius.
*
[IP05725(ALL)01/95]
Automatic operation
[IP05825(ALL)03/95]
Press the AUTO button and select the desired
temperature. The selected temperature and
AUTO will be shown in the Display window.
The EATC will automatically heat or cool to
achieve the set temperature. Under normal
conditions, your EATC will need no additional
attention.
[IP05925(ALL)02/95]
one inch art:0001287-B
The AUTO temperature display
[IP06025(ALL)03/95]
When in AUTO and weather conditions require
heat, air will be sent to the floor. But a feature is
included in your EATC to prevent blowing cold
air to the floor if the engine coolant is not warm
enough to allow heating. The EATC will direct
the airflow to the windshield at low fan speed.
In 3-1/2 minutes or less, the fan speed will start
to increase and the airflow will change to the
floor area.
File:06fcipt.ex
Update:Tue Jan 23 08:13:16 1996
ProCarManuals.com

105 [IP22200(ALL)04/95]
one inch art:0000651-E
The button that controls the rear window defroster and
heated side view mirrors
[IP22300(ALL)04/95]
Clear away any snow that is on the rear
window and side view mirrors before using the
defroster. With the engine running, push the
defrost button. After 10 minutes, the defroster
will turn off. If the window and mirrors are still
not clear, push the defroster button again. The
defroster will turn off when the ignition key is
turned to the OFF position.
%*
[IP23000(ALL)09/95]
NOTE: Never use sharp instruments or
window cleaners with abrasives to
clean the inside of your rear window.
If you do, you may damage the heating
elements that are bonded to the inside
of the rear window and cause damage
to the rear window defroster.
% [IP23200(ALL)12/95]
Liftgate Window Wiper and Washer
(If equipped)
[IP23401(ALL)04/95]
quarter page art:0000696-E
The liftgate window wiper and washer switches
[IP23500(ALL)04/95]
To turn on the liftgate window wiper, press the
bswitch. To turn the liftgate window wiper
off, press the switch again.
File:06fcipt.ex
Update:Tue Jan 23 08:13:16 1996
ProCarManuals.com

120 [SC06650(ALL)11/94]
one third page art:0000658-BThe lever to tilt the steering wheel
*
[SC06800(ALL)04/95]
To change the position of the steering
column/wheel, pull the release lever on the
column toward you. Tip the steering wheel to
the desired position. Release the lever to lock the
steering wheel in place.
%
*
[SC07400(ALL)03/91]
Cruise Control (If equipped)
*
[SC07500(ALL)06/95]
If your vehicle has cruise control, you can
automatically maintain a constant speed at or
above 30 mph (50 km/h).
*
[SC07550(ALL)09/95]
NOTE: Do not shift to N (Neutral) when using
the cruise control. This will cause the
engine to overspeed.
*
[SC07600(ALL)06/95]
Use of radio transmitting equipment that is not
Federal Communications Commission (FCC) or
in Canada the Canadian Radio and
Telecommunications Commission (CRTC)
approved may cause the speed control to
malfunction. Therefore, use only properly
installed FCC (CRTC in Canada) approved radio
transmitting equipment in your vehicle.
File:07fcsct.ex
Update:Mon Jan 22 15:52:32 1996
ProCarManuals.com

141
key. Additional spare keys, maximum of 14, can
be purchased either through your dealership or
selected retailers. Be sure to purchase only coded
keys with a Ford or Mercury logo on it to
ensure proper functionality. If both supplied
keys are lost or stolen or only one key has been
lost and you want to ensure that key will not
start the vehicle, the vehicle must be taken to
the dealership for re-initialization. (All keys must
be brought to the dealer, if any.)
[FV10808(ALL)04/95]
THEFT indicator
*
[FV10810(ALL)10/95]
The indicator provides system proveout and
operating status. The system activates the
indicator when the ignition switch is placed in
the ON or START position. This indicator helps
to determine possible fault conditions and/or
normal operating proveout. The system will
illuminate the indicator for two (2) seconds then
go out to acknowledge normal operating
conditions. If the indicator does not illuminate at
key ON or flashes, have the system serviced.
*
[FV10812(ALL)10/95]
Spare Key Programming Procedure
*
[FV10814(ALL)10/95]
Two electronically coded keys were supplied
with your vehicle, use one of these with the
procedure below:
*
[FV10816(ALL)10/95]
q
Using a coded key that you can start your
engine with, turn the ignition from the ON to
the OFF position.
*
[FV10820(ALL)10/95]
q
Within 15 seconds, insert a new key into the
ignition and turn it to ON or START. The
vehicle does not have to be started.
*
[FV10825(ALL)10/95]
If the key has been coded, the theft indicator
will illuminate for two seconds. The key can
then be used to start the vehicle.
*
[FV10826(ALL)10/95]
Repeat until all chosen keys have been coded
(max=16).
File:08fcfvt.ex
Update:Mon Jan 22 15:57:12 1996
ProCarManuals.com

191
Driving Your Taurus
*
[DR00300(ALL)07/95]
Your vehicle will have one of the following
types of transaxles:
*
[DR00500(ALL)11/94]
q
an automatic overdrive transaxle, or
[DR00510(ALL)02/95]
q
an automatic overdrive transaxle with
Overdrive Off (O/D OFF) switch
*
[DR00700(ALL)11/94]
If you are not sure which transaxle your vehicle
has, talk to your dealer.
*
[DR00800(ALL)04/95]
Your vehicle is equipped with an Electronic
Powertrain Control Module that limits engine
and/or vehicle speeds with a cut-out mode to
promote durability.
% [DR03510(ALL)04/95]Driving with an Automatic
Overdrive Transaxle (Column
Gearshift without O/D OFF
Switch)
%*
[DR03600(ALL)04/95]
Your automatic overdrive transaxle provides
fully automatic operation in eitherj
(Overdrive) or D (Drive). Driving with the shift
selector inj(Overdrive) gives the best fuel
economy for normal driving conditions. For
manual control, start in 1 (First) and then shift
manually.
File:10fcdrt.ex
Update:Mon Jan 22 15:59:33 1996
ProCarManuals.com

192 %
*
[DR03800(ALL)01/95]
Putting Your Vehicle in Gear
*
[DR04001(ALL)05/95]
RWARNING
Hold the brake pedal down while you
move the gearshift lever from position to
position. If you do not hold the brake
pedal down, your vehicle may move
unexpectedly and injure someone.
*
[DR04050(ALL)03/95]
To operate:
*
[DR04101(ALL)01/95]
1. Start the engine.
*
[DR04150(ALL)01/95]
2. Depress and hold the brake pedal.
*
[DR04201(ALL)01/95]
3. Move the gearshift lever out of P (Park).
%*
[DR04250(ALL)04/95]
Your vehicle is equipped with a Brake Shift
Interlock safety feature. This feature prevents the
gearshift from being moved from the P (Park)
position until the brake pedal is depressed. This
feature is active when the ignition is in the ON
position. If the gearshift lever CANNOT be
moved from P (Park) with the brake pedal
depressed:
*
[DR04300(ALL)01/95]
1. Turn the engine off and remove the ignition
key.
[DR04350(ALL)11/94]
2. Reinsert the ignition key and turn clockwise
to the first position (OFF).
[DR04400(ALL)11/94]
3. Depress the brake pedal, move the gearshift
lever to N (Neutral) and start the engine.
*
[DR04425(ALL)07/95]
If you need to shift out of P (Park) by using the
alternate procedure described above, it is
possible that a fuse has blown and that your
brakelamps may also not be functional. Please
refer to the chapter titledServicing Your Taurus
in this Owner Guide for instructions on checking
and replacing fuses.
File:10fcdrt.ex
Update:Mon Jan 22 15:59:33 1996
ProCarManuals.com

194 %
*
[DR05300(ALL)01/95]
Driving
%*
[DR05400(ALL)04/95]
When to usej(Overdrive)
*
[DR05500(ALL)04/95]
j(Overdrive) is the usual driving position for
an automatic overdrive transaxle. It works the
same way D (Drive) works, automatically
upshifting or downshifting as the vehicle speeds
or slows.
*
[DR05600(ALL)04/95]
However,j(Overdrive) also shifts into a fourth
gear Ð an overdrive gear Ð when your vehicle
cruises at a consistent speed for any length of
time. This fourth gear will increase your fuel
economy when you travel at cruising speeds.
*
[DR05800(ALL)06/95]
When to use D (Drive)
[DR06000(ALL)12/95]
D (Drive) eliminates the excessive shifting
between third and fourth gears that your vehicle
sometimes does when you are traveling through
hilly terrain inj(Overdrive). It also provides
more engine braking thanj(Overdrive) for
descending hills or city driving.
*
[DR06100(ALL)06/95]
When to use 1 (First)
*
[DR06200(ALL)11/94]
Use 1 (First) when added engine braking is
desired when descending steep hills.
*
[DR06220(ALL)11/94]
The automatic transaxle will shift to the proper
gear to ascend any grade without any need to
shift to 1 (First).
[DR06300(ALL)04/95]
Do not go faster than 38 mph (61 km/h) in this
gear. You can upshift from 1 (First) to D (Drive)
or from 1 (First) toj(Overdrive) at any speed.
*
[DR06400(ALL)01/95]
P (Park)
*
[DR06500(ALL)11/94]
Always come to a complete stop before you shift
into P (Park). Make sure that the gearshift is
securely latched in P (Park). This locks the
transaxle and prevents the front wheels from
rotating.
File:10fcdrt.ex
Update:Mon Jan 22 15:59:33 1996
ProCarManuals.com

196
*
[DR06745(ALL)03/95]
To operate:
*
[DR06750(ALL)01/95]
1. Start the engine.
*
[DR06755(ALL)01/95]
2. Depress and hold the brake pedal.
*
[DR06760(ALL)01/95]
3. Move the gearshift lever out of P (Park).
%*
[DR06765(ALL)04/95]
Your vehicle is equipped with a Brake Shift
Interlock safety feature. This feature prevents the
gearshift from being moved from the P (Park)
position until the brake pedal is depressed. This
feature is active when the ignition is in the ON
position. If the gearshift lever CANNOT be
moved from P (Park) with the brake pedal
depressed:
*
[DR06770(ALL)01/95]
1. Turn the engine off and remove the ignition
key.
[DR06775(ALL)11/94]
2. Reinsert the ignition key and turn clockwise
to the first position (OFF).
[DR06780(ALL)11/94]
3. Depress the brake pedal, move the gearshift
lever to N (Neutral) and start the engine.
*
[DR06781(ALL)07/95]
If you need to shift out of P (Park) by using the
alternate procedure described above, it is
possible that a fuse has blown and that your
brakelamps may also not be functional. Please
refer to the chapter titledServicing Your Taurus
in this Owner Guide for instructions on checking
and replacing fuses.
*
[DR06783(ALL)09/95]
RWARNING
DO NOT DRIVE YOUR VEHICLE UNTIL
YOU VERIFY THAT THE BRAKELAMPS
ARE WORKING.
File:10fcdrt.ex
Update:Mon Jan 22 15:59:33 1996
ProCarManuals.com