reset FORD TAURUS 1996 Owners Manual

63
*
[ST09400(ALL)08/95]
Whenever you start your vehicle, release the key
as soon as the engine starts. Excessive cranking
could damage the starter.
*
[ST09410(ALL)05/95]
After you start the engine, let it idle for a few
seconds. Keep your foot on the brake pedal and
put the gearshift lever in gear. Release the
parking brake. Slowly release the brake pedal
and drive away in the normal manner.
[ST09420(ALL)09/95]
NOTE: Your vehicle is equipped with an
automatic transaxle and has an
interlock that prevents you from
shifting out of P (Park) unless your
foot is on the brake pedal.
%*
[ST09480(ALL)04/95]
If the engine does not start after two attempts:
*
[ST09492(ALL)04/95]
1. Turn the ignition key to the OFF position.
*
[ST09494(ALL)04/95]
2. Press the accelerator all the way to the floor
and hold it.
*
[ST09496(ALL)04/95]
3. Turn the ignition key to the START position.
*
[ST09497(ALL)04/95]
4. Release the ignition key when the engine
starts.
*
[ST09498(ALL)04/95]
5. Release the accelerator gradually as the
engine speeds up. Then drive away in the
normal manner.
*
[ST09500(ALL)04/95]
If the engine still does not start, the fuel pump
shut-off switch may have been triggered. For
directions on how to reset the switch seeFuel
Pump Shut-Off Switchlater in this chapter.
[ST10200(ALL)12/95]
A computer system controls the engine's idle
speed. When you start your vehicle, the engine's
idle speed normally runs high. These faster
engine speeds will make your vehicle coast
slightly faster than its normal idle speed. It
should, however, slow down after a short time.
If it does not, have the idle speed checked by
your dealer or a qualified technician.
File:04fcstt.ex
Update:Mon Jan 22 15:46:50 1996
ProCarManuals.com

65
*
[ST11000(ALL)03/95]
For best results, plug the heater in at least three
hours before you start your vehicle. Using the
heater for longer than three hours will not
damage the engine, so you can plug it in at
night to start your vehicle the following
morning.
*
[ST11100(ALL)05/95]
RWARNING
To prevent electrical shock, do not use
your heater with ungrounded electrical
systems or two-pronged (cheater) adapters.
%
*
[ST11200(ALL)03/95]
If the Engine Cranks but Does
Not Start or Does Not Start After
a Collision
%*
[ST11300(ALL)11/95]
Fuel Pump Shut-off Switch
*
[ST11400(ALL)11/95]
If the engine cranks but does not start or does
not start even after a small collision, the fuel
pump shut-off switch may have been activated.
The shut-off switch is a device intended to stop
the fuel pump when your vehicle has been
involved in a substantial jolt.
[ST11500(ALL)10/95]
Once the shut-off switch is activated, you must
reset the switch by hand before you can start
your vehicle. If you have asedan, the switch is
on the right side of the trunk behind the trunk
liner. If you have awagon, it is behind the
service panel on the right side of the cargo area.
File:04fcstt.ex
Update:Mon Jan 22 15:46:50 1996
ProCarManuals.com

66 [ST11600(ALL)11/94]
half page art:0000399-EThe right side of the trunk in the sedan
[ST11700(ALL)11/94]
one third page art:0000516-E
Inside the right side service panel in the wagon
*
[ST11800(ALL)05/95]
RWARNING
If you see or smell fuel, do not reset the
switch or try to start your vehicle. Have
all the passengers get out of the vehicle
and call the local fire department or a
towing service.
File:04fcstt.ex
Update:Mon Jan 22 15:46:50 1996
ProCarManuals.com

67
*
[ST11900(ALL)03/95]
If your engine cranks but does not start after a
collision or substantial jolt:
*
[ST11950(ALL)04/95]
1. Turn the ignition key to the OFF position.
*
[ST12000(ALL)03/95]
2. Check under the vehicle for leaking fuel.
*
[ST12050(ALL)01/95]
3. If you do not see or smell fuel, push the red
reset button on the fuel pump shut-off
switch down.
*
[ST12100(ALL)03/95]
4. Turn the ignition key to the ON position for
a few seconds, then turn it to the OFF
position.
*
[ST12150(ALL)03/95]
5. Check under the vehicle again for leaking
fuel.If you see or smell fuel, do not start
your vehicle again.If you do not see or
smell fuel, you can try to start your vehicle
again.
*
[ST12200(ALL)03/95]
6. Check all vehicle warning lights before
driving the vehicle.
*
[ST12225(ALL)01/95]
Pushing
*
[ST12250(ALL)09/95]
Vehicles with automatic transaxles cannot be
started by pushing. Follow the directions under
If Your Vehicle Needs a Jump-Startin theRoadside
EmergenciesChapter.
File:04fcstt.ex
Update:Mon Jan 22 15:46:50 1996
ProCarManuals.com

84 %
*
[LG09800(ALL)01/95]
Speedometer
*
[LG09900(ALL)01/95]
The speedometer tells you how many miles
(kilometers) per hour your vehicle is moving.
%*
[LG10000(ALL)01/95]
Odometer
*
[LG10100(ALL)01/95]
The odometer tells you the total number of miles
(kilometers) your vehicle has been driven.
%*
[LG10200(ALL)11/94]
Trip Odometer
*
[LG10300(ALL)11/94]
The trip odometer tells you how many miles
(kilometers) your vehicle has been driven since
the last reset. Press the reset button to return the
trip odometer to zero.
%*
[LG10320(ALL)02/95]
Tachometer
[LG10340(ALL)02/95]
The tachometer tells you the approximate engine
revolutions per minute (how fast the engine is
running). You may damage the engine if you
drive with the indicator in the red zone.
% [LG10350(ALL)12/95]The Optional and SHO Clusters
[LG10360( T)02/95]
The optional cluster and the SHO cluster have
indicator lights that are not on the standard
cluster. For details about these lights, read the
information below. To learn about the standard
warning lights and gauges that come on all
clusters, seeThe Standard Clusterearlier in this
chapter.
[LG10365( T)12/95]
The optional cluster has a 120 mph (200 km/h)
speedometer and a 7,000 rpm tachometer.
[LG10370( T)02/95]
The SHO cluster also has a 150 mph (240 km/h)
speedometer and an 8,000 rpm tachometer.
File:05fclgt.ex
Update:Tue Jan 23 08:14:15 1996
ProCarManuals.com

99 [IP05650(ALL)10/95]
Changing the display from farenheit to
celsius
[IP05675(ALL)10/95]
To change the temperature display from
Farenheit to Celsius, depress the MAX A/C and
VF-DEF at the same time and hold them
down for about a second. To change back to the
original setting, repeat the process. If the battery
is disconnected, the display will revert to
Fahrenheit and must be reset to Celsius.
*
[IP05725(ALL)01/95]
Automatic operation
[IP05825(ALL)03/95]
Press the AUTO button and select the desired
temperature. The selected temperature and
AUTO will be shown in the Display window.
The EATC will automatically heat or cool to
achieve the set temperature. Under normal
conditions, your EATC will need no additional
attention.
[IP05925(ALL)02/95]
one inch art:0001287-B
The AUTO temperature display
[IP06025(ALL)03/95]
When in AUTO and weather conditions require
heat, air will be sent to the floor. But a feature is
included in your EATC to prevent blowing cold
air to the floor if the engine coolant is not warm
enough to allow heating. The EATC will direct
the airflow to the windshield at low fan speed.
In 3-1/2 minutes or less, the fan speed will start
to increase and the airflow will change to the
floor area.
File:06fcipt.ex
Update:Tue Jan 23 08:13:16 1996
ProCarManuals.com

123 [SC09350(ALL)03/95]
NOTE: When driving uphill, especially with a
heavy load, you may notice your speed
decreasing even if you have the cruise
control set. If the speed drops more
than 8 to 14 mph (13-23 km/h) it is
normal for the automatic cruise control
feature to be cancelled. You may need
to use the accelerator pedal to help
your vehicle maintain the selected
speed when driving up steep grades.
%*
[SC09400(ALL)08/95]
Resetting the Cruise Control
*
[SC09410(ALL)08/95]
To reset the cruise control to alower speed, use
one of the following procedures:
*
[SC09415(ALL)08/95]
q
COASTÐ Press and hold the COAST switch.
Release the switch when the vehicle slows
down to the desired speed.
*
[SC09420(ALL)08/95]
q
Lightly tap the brake pedal. When the vehicle
attains the desired speed, press the SET
ACCEL switch and release it immediately.
% [SC09425(ALL)11/94]
q
TAP-DOWNÐ Press and then quickly
release the COAST switch. Each time you
ªtapº the switch, the set speed will decrease
by 1 mph (1.6 km/h). Multiple taps will
cause the set speed to decrease in increments
of 1 mph (1.6 km/h). For example, if the
current set speed is 60 mph (96 km/h) 5 taps
of the COAST switch will decrease the
vehicle speed and SET it at 55 mph
(88 km/h).
*
[SC09430(ALL)08/95]
If vehicle speed is reduced below 30 mph
(50 km/h) by any of the above methods, then
you must manually accelerate to a speed over
30 mph (50 km/h) and reset the system.
File:07fcsct.ex
Update:Mon Jan 22 15:52:32 1996
ProCarManuals.com

124 [SC09435(ALL)02/95]To reset the cruise control to ahigher speed,
use one of the following procedures:
*
[SC09440(ALL)08/95]
q
ACCELÐ Press and hold the SET ACCEL
switch. Release the switch when the vehicle
has accelerated to the desired speed.
*
[SC09445(ALL)08/95]
q
Depress the accelerator pedal. When the
vehicle attains the desired speed, press the
SET ACCEL switch and release it
immediately.
% [SC09450(ALL)11/94]
q
TAP-UPÐ Press and then quickly release the
SET ACCEL switch. Each time you ªtapº the
switch, the set speed will increase by 1 mph
(1.6 km/h). Multiple taps will cause the set
speed to increase in increments of 1 mph
(1.6 km/h). For example, if the current set
speed is 55 mph (88 km/h) 5 taps of the SET
ACCEL switch will increase the vehicle speed
and SET it at 60 mph (96 km/h).
*
[SC10900(ALL)11/95]
Cancelling and Resuming a Set Speed
[SC11000(ALL)04/95]
If you press the brake pedal, cruise control is
cancelled. You can return to the set speed by
pressing the RESUME switch, as long as you did
not press the OFF switch. You must be driving
at least 30 mph (50 km/h).
*
[SC11300(ALL)05/95]
Your vehicle will gradually return to the
previously set speed and then maintain it.
%*
[SC11315(ALL)08/95]
To Turn Off the Cruise Control System
*
[SC11325(ALL)08/95]
Press the OFF switch.
*
[SC11400(ALL)10/95]
In addition, the cruise control is turned off each
time you turn the vehicle ignition off.
File:07fcsct.ex
Update:Mon Jan 22 15:52:32 1996
ProCarManuals.com

131
*
[FV05550(ALL)09/95]
Locking the doors with the keyless entry
system
*
[FV05601(ALL)09/95]
Along with unlocking your doors, you can use
the keyless entry system to lock the doors. You
can also use the Autolock feature to
automatically lock the doors after you get in the
vehicle.
*
[FV05650(ALL)02/95]
To lock all of the doors, press 7/8 and 9/0 at
the same time. It is not necessary to first enter
the keypad code. This will arm your factory
installed anti-theft system, if so equipped.
[FV05701(ALL)03/95]
Arming, disarming and resetting your
perimeter anti-theft system (If equipped)
from the keyless entry pad
*
[FV05750(ALL)05/95]
If your vehicle is equipped with the optional
factory installed anti-theft system, the keyless
entry system will arm it when you use the 7/8
and 9/0 keys to lock the doors, and will disarm
or reset a triggered anti-theft alarm when you
enter in the five digit code to unlock the driver's
door.
*
[FV05800(ALL)09/95]
NOTE: Doors and the liftgate must be fully
closed for the anti-theft system to arm.
Refer to theAnti-Theft Systemsection
in this chapter for more details.
File:08fcfvt.ex
Update:Mon Jan 22 15:57:12 1996
ProCarManuals.com

136 [FV08251(ALL)04/95]THIS DEVICE COMPLIES WITH PART 15 OF
THE FCC RULES. OPERATION IS SUBJECT
TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND (2) THIS
DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
%*
[FV08300(ALL)04/95]
Arming and Disarming the Alarm System
with Remote Entry
*
[FV08351(ALL)04/95]
Your Remote Entry System will automatically
arm the factory installed Anti-Theft System when
the doors are locked, and automatically disarm it
when the doors are unlocked. The remote will
also reset the anti-theft alarm (when the driver's
door is unlocked or the PANIC button is pressed
on a programmed remote entry transmitter) if it
was triggered.
*
[FV08400(ALL)04/95]
The remote entry system may not arm and
disarm non-factory installed anti-theft systems.
%*
[FV08451(ALL)02/95]
Replacing the batteries
*
[FV08500(ALL)02/95]
The remote entry transmitter is powered by two
coin type three-volt lithium 2016
batteries (included) that should last for several
years of normal use. If you notice a significant
decrease in operating range, the batteries should
be replaced. Replacement batteries can be
purchased at most pharmacies, watch stores or
at your Ford or Lincoln-Mercury dealer.
File:08fcfvt.ex
Update:Mon Jan 22 15:57:12 1996
ProCarManuals.com