lock FORD WINDSTAR 1996 1.G Workshop Manual

Electronic Sound Systems
227
*
[AS23160(ALL)02/95]
n
Using the ªSCANº function (Stereo Cassette Radio)
*
[AS23170(ALL)07/94]
Press the ªSCANº button to enter the scan mode. The radio
will begin scanning up the frequency band, stopping on each
listenable station for approximately a five-second sampling.
This continues until you press the ªSCANº button a second
time. The display flashes ªAMº or ªFM.º
*
[AS23200(ALL)01/95]
n
Setting the station MEMORY PRESET buttons
*
[AS23325(ALL)05/95]
Your radio is equipped with 5 station memory buttons.
These buttons can be used to select up to 5 preset AM
stations and 10 preset FM stations (5 in FM1 and 5 in FM2).
*
[AS23400(ALL)02/95]
Follow the easy steps below to set these buttons to the desired
frequencies:
*
[AS23500(ALL)04/95]1.
Select a band, then select a frequency.
*
[AS23700(ALL)04/95]2.
Press one of the memory buttons and hold the button until
the sound returns. That station is now held in memory on
that button.
*
[AS23800(ALL)04/95]3.
Follow the two steps above for each station memory preset
button you want to set.
*
[AS23900(ALL)04/95]
NOTE: If the vehicle's battery is disconnected, the clock and
station memory preset buttons (if programmed in auto
mode) will need to be reset.
*
[AS24000(ALL)02/95]
Adjusting the tone balance and speaker output of your
radio
*
[AS24100(ALL)04/95]
n
Increasing or decreasing bass response
*
[AS24225(ALL)05/95]
Push the ªAUDIOº button repeatedly until the display reads
ªBASS.º Push the right (+) side of the ªVOLUMEº button to
increase bass (more ªlowsº), and push the left (-) side to
decrease bass (less ªlowsº).
File:wnass.ex
Update:Tue Mar 19 08:19:39 1996

Electronic Sound Systems
231
*
[AS27600(ALL)02/95]
Tips on Caring for the Cassette Player and Tapes
*
[AS27700(ALL)02/95]
In order to keep your cassette tape player performing the way it
was meant to, read and follow these simple precautions:
*
[AS27750(ALL)02/95]
n
Using a Ford Cassette Cleaning Cartridge to clean the tape
player head after 10-12 hours of play will help maintain the
best playback sound and proper tape operation.
*
[AS27800(ALL)02/95]
n
Only cassettes that are 90 minutes long or less should be
used. Tapes longer than 90 minutes are thinner and subject
to breakage or may jam the tape player mechanism.
*
[AS27900(ALL)02/95]
n
Protect cassettes from exposure to direct sunlight, high
humidity and extreme heat or cold. If they are exposed to
extreme conditions, allow them to reach a moderate
temperature before playing.
*
[AS28001(ALL)02/95]
n
If a tape is loose inside the cassette, tighten it before playing
by putting your finger or a pencil into one of the holes and
turning the hub until the tape is tight.
*
[AS28101(ALL)02/95]
n
Loose labels on cassette tapes can become lodged in the
mechanism. Remove any loose label material before inserting
a cassette.
*
[AS28200(ALL)03/95]
n
Do not leave a tape in the cassette tape player when not in
use. High heat in the vehicle can cause the cassette to warp.
%*
[AS28400(ALL)03/95]
Clock Operation
*
[AS28500(ALL)07/90]
How to view the clock mode
*
[AS28650(ALL)07/93]
Press the ªCLOCKº button to alternate the frequency and time
in the display. In the clock mode, pressing any radio function
will automatically display the radio frequency for
approximatedly ten seconds before changing back to the clock
mode.
File:wnass.ex
Update:Tue Mar 19 08:19:39 1996

232
*
[AS28800(ALL)07/90]
How to set the clock
*
[AS28900(ALL)04/92]1.
Turn the radio on.
*
[AS29025(ALL)03/95]2.
Press and hold in the ªCLOCKº button, press the ªSEEKº
button left (
b) to advance the hours and right (
a)to
advance the minutes.
*
[AS29200(ALL)11/93]
NOTE: The clock displays 12-hour time with no AM/PM
indications.
%*
[AS35200(ALL)02/95]
Common Radio Reception Conditions
*
[AS35300(ALL)02/95]
Several conditions prevent FM reception from being completely
clear and noise-free, such as the following:
*
[AS35400(ALL)04/95]1.
Distance/Strength
*
[AS35500(ALL)02/95]
The strength of the FM signal is directly related to the distance
the signal must travel. The listenable range of an average FM
signal is approximately 25 miles (40 kilometers). Beyond this
distance, the radio is operating in a fringe area and the signal
becomes weaker.
*
[AS35600(ALL)04/95]2.
Terrain
*
[AS35700(ALL)02/95]
The terrain (hilly, mountainous, tall buildings) of the area over
which the signal travels may prevent the FM signal from being
noise-free.
*
[AS35900(ALL)01/95]
If there is a building or large structure between the antenna and
station, some of the signal ªbendsº around the building, but
certain spots receive almost no signal. Moving out of the
ªshadowº of the structure will allow the station to return to
normal.
*
[AS36000(ALL)01/95]
When the radio waves are reflected off objects or structures, the
reflected signal cancels the normal signal, causing the antenna to
pick up noise and distortion. Cancellation effects are most
prominent in metropolitan areas, but also can become quite
severe in hilly terrain and depressed roadways.
File:wnass.ex
Update:Tue Mar 19 08:19:39 1996

236
% [DR01600(ALL)09/93]
Brake-Shift Interlock Safety Feature
[DR01700(ALL)05/95]
Your vehicle has a special brake-shift interlock safety feature
which prevents you from shifting out of P (Park) without the
brake pedal depressed. To shift the transaxle out of the P (Park)
position, the ignition must be in the ON position and your foot
must be pressing on the brake pedal.
[DR01750(ALL)02/96]
When parking on a hill, set the parking brake before shifting
into and out of P (Park). If the parking brake is not set, a clunk
or bang may be heard when shifting out of P (Park). This noise
can be considered a normal characteristic.
*
[DR01800(ALL)04/95]
If the shift lever cannot be moved from the P (Park) position
with the brake pedal depressed:
*
[DR01900(ALL)01/93]1.
Shut the engine off and remove the ignition key.
*
[DR02000(ALL)01/93]2.
Apply the parking brake.
*
[DR02100(ALL)01/93]3.
Reinsert the ignition key and turn it clockwise to the first
position (OFF).
*
[DR02200(ALL)04/95]4.
Depress the brake pedal, move the gearshift lever to N
(Neutral) and start the engine.
*
[DR02280(ALL)05/95]
If you need to shift out of P (Park) by using the alternate
procedure described above, it is possible that a fuse has blown
and that your brakelamps may also not be functional. Please
refer to the chapter titledServicing Your Windstarin this Owner
Guide for instructions on checking and replacing fuses.
*
[DR02300(ALL)05/95]
RWARNING
DO NOT DRIVE YOUR VEHICLE UNTIL YOU VERIFY
THAT THE BRAKELAMPS ARE WORKING.
%*
[DR02500(ALL)06/92]
Backing Up
*
[DR02600(ALL)01/93]
Before shifting into or out of R (Reverse), you should always
come to a complete stop.
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

Driving Your Windstar
237
%*
[DR02700(ALL)01/95]
Driving
*
[DR02800(ALL)01/93]
When to use N (Neutral)
*
[DR02900(ALL)01/93]
In N (Neutral), the wheels of the transaxle are not locked. Your
vehicle will roll freely, even on the slightest incline, unless the
parking brake or brakes are on.
[DR03000(ALL)05/95]
When to usejOverdrive
[DR03100(ALL)06/95]
Overdrive is the normal driving position. When the gearshift
lever is placed injOverdrive , and the Overdrive Off button
has not been pressed, the vehicle will automatically upshift to
second, third and fourth gears. The transaxle will shift into the
correct gear when the right speed is reached.
%*
[DR03200(ALL)02/94]
When to use D (Drive) - with the Overdrive Off button
activated
[DR03300(ALL)06/94]
You will notice that there is only one drive position on your
gearshift indicator (instead of Drive and Overdrive). However,
you will find a button and an indicator light located on the
gearshift lever. Push in the button on the end of the lever and
the OVERDRIVE OFF light on the end of the gearshift lever will
illuminate. With the OVERDRIVE OFF light illuminated, the
transaxle will operate in first, second and third gears and will
not shift into fourth gear. Operating in Drive (OVERDRIVE OFF
light illuminated) provides more engine braking than Overdrive
for descending hills or city driving.
[DR03400(ALL)09/93]
6 pica art:0050058-A
Overdrive button location
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

238
*
[DR03500(ALL)09/93]
To return the transaxle to the normal Overdrive operation, press
the OVERDRIVE ON/OFF button again. Use this button to
select Overdrive or Overdrive Off whenever you drive your
vehicle.
*
[DR03700(ALL)02/95]
The transaxle will be in the ªoverdrive onº mode when the
vehicle is started even if the O/D OFF mode was selected when
the vehicle was last shut off.
*
[DR03900(ALL)04/95]
NOTE: If the O/D OFF indicator light is flashing on and off
repeatedly when the vehicle is started, there is a
transaxle electronic system malfunction. Contact your
dealer as soon as possible.
*
[DR04000(ALL)01/93]
When to use 2 (Second)
[DR04100(ALL)03/94]
Use 2 (Second) when driving on slippery roads or to provide
additional engine braking on downgrades. This position
provides Second and First gear operation only.
*
[DR04200(ALL)12/93]
When to use 1 (First)
[DR04300(ALL)05/95]
Use 1 (First) to provide maximum engine braking on steep
downgrades. Upshifts from First can be made by manually
shifting to 2 (Second) orj(Overdrive). 1 (First) gear provides
only first gear operation. If you select First while driving at
higher speeds, the transaxle will shift to 2 (Second), and then
downshift to 1 (First) after the vehicle decelerates to the proper
speed.
*
[DR04400(ALL)06/92]
Parking
*
[DR04500(ALL)01/93]
Always come to a complete stop before you shift into P (Park).
This position locks the transaxle and prevents the front wheels
from turning. To securely latch the gearshift in the P (Park)
position, pull it toward you, push it completely
counterclockwise against the stop, and then push it toward the
instrument panel.
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

Driving Your Windstar
239
[DR04600(ALL)05/95]
The gearshift is securely latched in P (Park) if you can not
rotate it in a clockwise direction without pulling it toward you.
*
[DR04700(ALL)05/95]
RWARNING
Always set the parking brake fully and make sure that
the gearshift is securely latched in P (Park).
*
[DR04800(ALL)05/95]
RWARNING
Never leave your vehicle unattended while it is running.
*
[DR04900(ALL)05/95]
RWARNING
Never leave your vehicle unattended while it is running.
*
[DR05000(ALL)06/94]
Forced Downshifts
[DR05100(ALL)05/95]
To gain extra acceleration in
j(Overdrive) (when passing
another vehicle) push the accelerator to the floor. The transaxle
will automatically downshift to the appropriate gear (third,
second or first).
% [DR05200(ALL)04/95]
Traction Control (If equipped)
[DR05300(ALL)04/95]
Traction Control can help improve your traction on slippery
surfaces, but always operate your vehicle within reasonable
limits. Abrupt changes in acceleration, deceleration, turning, or
combinations of these maneuvers can cause your vehicle to
behave differently than anticipated, especially when road
conditions vary.
[DR05400(ALL)04/95]
To turn Traction Control off, press the button located in the
glove compartment while the vehicle is stopped.
[DR05500(ALL)05/95]
Traction Control can be turned back on by pressing the button
again while the vehicle is stopped or by restarting the engine.
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

Driving Your Windstar
241
*
[DR06800(ALL)01/93]
Four-Wheel Anti-lock Brakes
*
[DR06900(ALL)01/94]
The Anti-lock Brake System (ABS) prevents wheels from
completely locking up by automatically releasing and
re-applying the brakes. During ABS braking, slight brake pedal
pulsations may be felt on the driver's foot. These pulsations
represent the rapid cycling of the ABS valves. The pedal
pulsations are considered normal ABS operation, and will stop
when normal braking is resumed or when the vehicle comes to
a stop.
%*
[DR07000(ALL)12/93]
During ABS activation, a mechanical noise may be heard as the
ABS system cycles. This is normal ABS operation.
*
[DR07100(ALL)12/93]
The ABS system has self-check capabilities. The system turns on
the ABS warning light each time you start the engine. After the
engine is started and the ABS warning light turns off, the
system performs another test the first time the vehicle reaches
4 mph (6 km/h). A mechanical noise may be heard as the ABS
system performs a self test. This is a normal part of the self test
feature. If a malfunction is found during this check, the ABS
warning light will come on.
[DR07150(ALL)12/93]
6 pica art:0050147-B
The anti-lock brake system light
*
[DR07200(ALL)12/93]
You should always be careful when braking, even if your
vehicle has the ABS system. Heavy braking on roads with loose
surfaces such as snow or gravel, or roads with severe pavement
irregularities could also cause you to lose control of your
vehicle.
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

242
*
[DR07300(ALL)05/95]
RWARNING
If the anti-lock brake system warning light remains on or
comes on while driving, have the braking system checked
by a qualified service technician as soon as possible.
*
[DR07320(ALL)05/95]
NOTE: If a fault occurs in the anti-lock system, and the brake
warning light is not lit, the anti-lock system is
disabled but normal brake function remains
operational.
*
[DR07350(ALL)12/93]
Ford Motor Company has not found any negative effects of
mobile radio transmitting equipment installed on vehicles with
the ABS system providing that the radio is installed according
to the radio manufacturer's instructions. However, if you have
had a mobile radio transmitter installed and the check ABS light
comes on (at any time other than immediately after turning the
key to the ON position) have your mobile radio dealer inspect
the radio installation. Also, if the ABS system is activated other
than during maximum braking, have your mobile radio
installation checked.
%*
[DR07400(ALL)12/89]
If Brakes Do Not Grip Well or Pedal is ªLowº
*
[DR07500(ALL)01/93]
If the brake pedal seems ªlowº it may indicate the need for a
brake system inspection and/or service. Apply your parking
brake several times. If the condition has not improved, you
should have your brakes checked as soon as possible.
%*
[DR07600(ALL)01/93]
Occasional brake squeal during light to moderate stops does not
affect the function of the brake system and is normal. However,
if the squeal becomes very loud or if it becomes more frequent,
return the vehicle to your dealer for inspection.
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

246
*
[DR09500(ALL)07/93]
For example, even with anti-lock brakes, extreme braking can
make it difficult to control the direction of the vehicle. Use a
ªsqueezeº technique. Push on the brake pedal with steadily
increasing force. This allows the wheels to brake, yet continue to
roll so that you may steer in the direction you want to travel.
*
[DR09600(ALL)01/93]
If you release the accelerator abruptly or brake hard while
going too fast around a severe curve, your vehicle may change
its direction of travel. Avoid applying the brakes, if possible. If
you must apply the brakes, use the ªsqueezeº technique
described earlier.
*
[DR09700(ALL)02/95]
Wheel Spin
[DR09800(ALL)05/95]
Extreme acceleration can cause the front wheels to spin,
resulting in reduced steering control. If the wheels spin during
vehicle start-up, shift to 2 (Second) gear. Move forward slowly
and evenly. If this does not work, try rocking the vehicle.
%*
[DR09900(ALL)01/93]
Driving at High Speeds
*
[DR10000(ALL)05/95]
RWARNING
Driving too fast for conditions creates the possibility of
loss of vehicle control. Driving at very high speeds for
extended periods of time may result in damage to vehicle
components.
*
[DR10020(ALL)05/95]
Ford Motor Company recommends obeying posted speed limits.
*
[DR10100(ALL)06/95]
RWARNING
Do not spin the wheels at over 35 mph (55 km/h). The
tires may fail and injure a passenger or bystander.
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996