jacking FORD WINDSTAR 1998 1.G Owners Manual

Roadside Emergencies
251
% [ER07700(ALL)04/96]
Changing the Tire
*
[ER07800(ALL)01/96]
You should only raise your vehicle with a jack properly placed
at the front or rear jacking points.
*
[ER07900(ALL)05/96]1.
Make sure that your vehicle will not move or roll and that
the tires and jack are on a level, solid surface. Put the
gearshift lever in P (Park). Set the parking brake and block
the wheel Ð in both directions Ð that is diagonally opposite
the tire that you are changing.
*
[ER08000(ALL)01/96]
RWARNING
When one of the front wheels is off the ground, the
transaxle alone will not prevent the vehicle from moving
or slipping off the jack, even if the vehicle is in P (Park).
*
[ER08100(ALL)01/96]
RWARNING
To prevent the vehicle from moving when you change a
tire, be sure the parking brake is set, then block (in both
directions) the wheel that is diagonally opposite (other
side and end of the vehicle) to the tire being changed.
*
[ER08200(ALL)03/96]
RWARNING
If the vehicle slips off the jack, you or someone else
could be seriously injured.
*
[ER08300(ALL)01/96]
RWARNING
On vehicles equipped with Air Suspension, turn OFF the
Air Suspension switch prior to jacking, hoisting or
towing your vehicle.
File:10wners.ex
Update:Mon Oct 7 11:47:52 1996

Roadside Emergencies
255
*
[ER09200(ALL)01/96]
7-1/2 pica art:0040182-A
Anti-theft lug nut
*
[ER09300(ALL)01/96]5.
Fit the jack under the proper jacking point indicated by the
notch in the bottom of the door frame panel.
[ER09400(ALL)01/96]
10-1/2 pica
art:0050210-B
The notches for the jack
File:10wners.ex
Update:Mon Oct 7 11:47:52 1996

256
[ER09500(ALL)01/96]
13-1/2 pica
art:0050047-B
Jack placement
[ER09600(ALL)01/96]
NOTE: If your vehicle is equipped with running boards, refer
to the following illustration before jacking.
File:10wners.ex
Update:Mon Oct 7 11:47:52 1996

Roadside Emergencies
257
[ER09700(ALL)01/96]
33-1/2 pica
art:0050211-A
Jacking information for running boards
File:10wners.ex
Update:Mon Oct 7 11:47:52 1996

Roadside Emergencies
261
*
[ER11700(ALL)01/96]
Stowing the spare tire
[ER11800(ALL)01/96]1.
To raise the tire to the stowed position, lay the tire on the
ground with the interior side facing up. Install the retainer
through the wheel center and slide the tire under the vehicle.
Fit the hex-shaped end of the wheel lug wrench over the hex
nut in the floor of the cargo area. Turn the wheel lug
wrench clockwise until the tire is raised to its original
position underneath the vehicle.
[ER11850(ALL)08/96]
If your vehicle has 16" wheels, lift one end of the tire, route the
cable end through the center of the wheel and install the 16"
wheel retainer.
[ER11900(ALL)01/96]
NOTE: The hex nut ratchets when the tire is raised to the
stowed position. It will not allow you to over-tighten.
*
[ER12000(ALL)01/96]2.
Check for proper seating against the underbody supports
and retighten if necessary.
[ER12100(ALL)01/96]
RWARNING
Check the tire seating position for looseness and make
sure the tire is not too far forward to avoid axle contact.
*
[ER12200(ALL)01/96]
RWARNING
Make sure the spare tire and jacking equipment are
stowed and secured in the proper storage location.
File:10wners.ex
Update:Mon Oct 7 11:47:52 1996