turn signal GEELY CK 2008 Workshop Manual

1772. SPEEDOMETER MALFUNCTION
CIRCUIT DIAGRAM
INSPECTION
(a) Inspect the combination meter assembly
1Remove the combination meter assembly and retain the connection of connectors.
2Inspect continuity
yInspect continuity between terminals
Standard:
3Inspect voltage between terminals
Standard:
Result and solution:
If it is abnormal, go to (b) Inspect the combination meter assembly speed input signal
If normal, go to (c) Inspect the combination meter assemblyTe ste r c onne c tion Condition Sta ndard c ondition
A9 - ground Norma l c ondition ContinuitySpeedometer SensorCombined Meter AssemblyGround the
Speedometer Sensor
Speedometer Sensor+8V
Power Source
Speed SignalTe ste r c onne c tion Condition Sta nda rd c ondition
A10 - ground Turn the ignition switch to ON 7.5 – 9V

178(b) Inspect the combination meter assembly speed input signal
1Inspect voltage
yHold the front wheels up
yPush the shift lever to NEUTRAL
yTurn the ignition switch to ON
ySlowly turn the front wheel, measure the voltage between terminal A9 and A11
Standard voltage is as follows:
Voltage changes alternately
Result and solution:
Normal Replace the combination meter assembly
If abnormal, inspect the speed sensor
2Inspect the speed sensor
y Inspect continuity
Inspect continuity between terminals
Standard:Tester connection Condition Standard condition
2 - ground Normal c ondition ContinuityTurning WheelsBelow 0.5V

179yInspect voltage between terminals
Standard:
Result and solution:
AbnormalRepair or replace the harness or connector
NormalInspect the speed sensor output signal
3Inspect the speed sensor output signal
Inspect voltage
yHold the front wheels up
yPush the shift lever to NEUTRAL
yTurn the ignition switch to ON
ySlowly turn the front wheel, measure the voltage between terminal 1 and 2
Standard voltage is as follows:
Voltage changes alternately
Result and solution:
NormalRepair or replace the harness or connector
Abnormalreplace the speed sensorTurning WheelsBelow 0.5VTe ste r c onne c tion Condition Sta nda rd c ondition
3 - ground Turn the ignition switch to ON 7.5 – 9V

1834. WATER TEMPERATURE GAUGE MALFUNCTION
CIRCUIT DIAGRAM
(a) Get the value of water temperature with the diagnosis tester
1Connect the diagnosis tester to the diagnosis interface
2Turn the ignition switch to ON
3Read the value of engine water temperature displayed on the diagnosis tester
Standard: The same with the actual engine coolant temperature.
Result and solution:
If it is normal, the water temperature gauge has no malfunction
If abnormal, Inspect the combination meter assembly
(b) Inspect the combination meter assembly
1Inspect resistance
yRemove the combination meter assembly and disconnect connectors
yInspect continuity between terminalsWater Temperature SensorCombined Meter Assembly
Water
Temperature
Signal

198Chapter 5 Light SystemSection 1 Survey of Light SystemI. COMPOSITION1. Front combination lamp assembly: turn signal lamp, high beam, low beam, head lamp, front position lamp.
2. Rear combination lamp: turn signal lamp, back-up lamp, rear fog lamp, tail lamp, brake lamp, retro reflector.
3. Front fog lamp
4. Side turn signal lamp
5. High mounted stop lamp
6. Rear trunk lamp
7. License plate lamp
8. Interior dome lamp
9. Rear row reading lamp
10. Door lampshield and bulb assemblyII. NOTES FOR REPAIR1. NOTES WHEN REPAIRING ELECTRICAL EQUIPMENTS
(a) Disconnect the battery ground cable.
2. Notes when replacing a headlamp bulb
(a) Before replacing a halogen bulb, turn the headlamp OFF to make it cool.
(b) When installing a new halogen bulb, do not touch the glass part of the bulb with bare hands.
(c) If there is oil stain on the surface of halogen bulb (headlamp and front fog lamp) when the lamps are
turned ON, its service life will be shortened.
(d) Halogen bulbs (headlamp and front fog lamp) have pressurized gas inside and require special handling.
They can explode if dropped to ground.The glass fragments will splash up.
(e) When replacing, make sure to use the bulbs with the same power, same model.
(f) After the bulb is installed, make the lamp holder tight.

200IV. LOCATION OF LIGHT SYSTEMFuse BoxInterior LampRear Row
Reading LampLH Turn Lamp Assembly
Lamp Assembly LH Front Fog Assembly
Front Headlamp Height
Adjusting SwitchHeadlamp Switch Lamp
Control Switch, Haedlamp
DIM Switch Turn Signal
Lamp SwitchHazard Warning
SwitchParking Brake SwitchBackup Lamp Switch
Brake SwitchDoor Courtesy Lamp Switch
LH/Front, Rear Door
Courtesy Lamp Assembly
LH Front Combined

2044. TURN SIGNAL AND HAZARD WARNING SYSTEM
5. BRAKE LAMP SYSTEMSymptom Suspec te d Area
1. HAZARD Fuse
2. Ce ntra l c ontrolle r
3. H a rne ss
1. Hazard warning switch
2. H a rne ss
1. Turn s igna l sw itc h
2. H a rne ss
1. Turn s igna l sw itc h
2. H a rne ss
1. Bulb
2. H a rne ss Only one bulb dose not light up “Haza rd" a nd “Turn” doe s not ope ra te
Ha za rd wa rning la mp doe s not ope ra te (Turn is
norma l)
Ha za rd wa rning la mp is abnormal (Ha za rd is
a bnorma l)
Turn signa l dose not light up in one direc tionSymptom Suspec te d Area
1. Bra ke la mp fus e
2. Brake lamp switch
3. H a rne ss
1. Brake lamp switch
2. H a rne ss
1. Bulb
2. H a rne ss
1. Bulb
2. H a rne ss Brake la mps on both side s do not light up
Br a ke la mp re ma ins a lw a ys O N
Bra ke la mp dose not light (One side )
High mounte d Bra ke la mp dose not light up
(Stop la mp is norma l)

207(a) Inspect light control switch continuity
Inspect each terminal for continuity when the switch is on every position according to the table.
If it is not as specified, replace the switch.
(b) Inspect headlamp dimmer switch continuity
Inspect each terminal for continuity when the switch is on every position according to the table.
If it is not as specified, replace the switch.
(c) Inspect turn signal switch continuity
Inspect each terminal for continuity when the switch is on every position according to the table.
If it is not as specified, replace the switch.S w it c h pos it ion T e s t e d t e r mina l C ondit ion
O FF 5BB2-5BB3 No c ontinuity
TAIL 5BB2-5BB3 ContinuitySwitch position Tested terminal Condition
LO 5BB1-9NB5 Continuity
HI 9NB2-9NB3 Continuity
PASSING 9NA1-9NB3 Continuity5B
5BB1
5BB2
5BB35BA1
5BA39N
9NB1
9NB2
9NB3
9NB4
9NB59NA1
9NA2
9NA3
9NA4Headlamp combinated terminal position diagramSwitch position Tested terminal Condition
Left turn 9NA4-9NA5 Continuity
Straight run 9NA4-9NA5-9NA2 No c ontinuity
Right turn 9NA5-9NA2 Continuity

212II.INSTALLATION1. Install the electrical connector of the headlamp assembly.
2. Install the headlamp assembly and the 3 mounting bolts.
3. Install the front bumper.
4. Adjust the condition of the vehicle.
5. Adjust the headlamp beam.III.HEADLAMP BULB REPLACEMENT1 - LOW BEAM DUST COVER 2 - HIGH BEAM DUST COVER 3 - TURN SIGNAL LAMP DUST
COVER 4 - HEADLAMP HOLDER
1. Replace the high and low beam bulbs
y Turn and remove the dust cover counter-clockwise
y Pull out the bulb plug
y Press and release the wire clip
y Pull out the lamp-holder, and remove the bulb
y Replace the bulb
2. Replace the turn signal lamp bulbs
y Remove the 3 screws on the dust cover with screwdriver
yTurn the lamp-holder counter-clockwise. Pull out the lamp-holder, and remove the bulb
yReplace the bulb
3. Replace the headlamp bulbs
yTurn the lamp-holder counter-clockwise. Pull out the lamp-holder, remove the bulb, and replace the
bulb.1 2 3 4

224Section 2 Audio System Connector Terminal Layout1. Connector terminal layout on wire harness
2. Connect terminal definitionTerminal
No.Func tion Wire color Condition Standard Voltage
A1 FR+ Lg The audio system is onWave form is synchronized w ith
the output sound
A2 FL+ YB The audio system is onWave form is synchronized w ith
the output sound
A3 ACC RW Ignition sw itc h turned to ACC 10
～14V
A4 B+ R Constant Status 10
～14V
A5 FR- LgR The audio system is onWave form is synchronized w ith
the output sound
A6 FL- Y The audio system is onWave form is synchronized w ith
the output sound
A7 GND B Constant Status Continuity
A8 N u ll
A9 N u ll
A1 0 T AI L G WPosition lamp switc h turned to
ON10
～14V
B1 RR+ PB The audio system is onWave form is synchronized w ith
the output sound
B2 RL+ YR The audio system is onWave form is synchronized w ith
the output sound
B3 RR- P The audio system is onWave form is synchronized w ith
the output sound
B4 N u ll
B5 N u ll
B6 RL- YW The audio system is onWave form is synchronized w ith
the output sound
C1 B+ Constant Status 10
～14V
C2 BUS Audio s ystem is On Pulse Signal
C3 GND Constant Status Continuity
C4 ACC Ignition sw itc h ACC 10
～14V
C5 Null
C6 R-OUT The audio system is onWave form is synchronized w ith
the output sound
C7 L-OUT The audio system is onWave form is synchronized w ith
the output sound
C8GND(Audio
Frequenc y)Constant Status Continuity